期刊文献+

燃气流量对超音速火焰喷涂Cr_3C_2-NiCr涂层组织与冲蚀性能的影响 被引量:7

Effect of Fuel Flow on Microstructure and Erosion Performance of HVOF Sprayed Cr_3C_2-NiCr Coating
在线阅读 下载PDF
导出
摘要 在氧气流量和喷涂距离一定的条件下,揭示了燃气流量对超音速火焰喷涂Cr3C2-NiCr涂层显微结构及冲蚀性能的影响,并探讨了冲蚀角度对Cr3C2-NiCr涂层冲蚀性能的影响。结果表明:在相同冲蚀角度下,高燃气流量制备的涂层损耗率小;随着冲蚀角度的增加,涂层的损耗率逐渐增加;在90°时,损耗率达到最大。 This paper investigated the effect of fuel flow on microstructure and erosion performance with the flow rate of O2 and spraying distance maintained constant, and discussed erosion angle affect on the erosion wear performance of Cr3C2-NiCr coatings, the results indicate when the erosion angle is kept same, the erosion wastage ratio of the coatings prepared with high flows is low; the erosion wastage ratio of the coatings increase along with the erosion angle increasing; when the erosion angle is 90, the erosion wastage ratio reaches at the maximum.
出处 《中国表面工程》 EI CAS CSCD 2008年第1期41-44,共4页 China Surface Engineering
关键词 超音速火焰喷涂 CR3C2-NICR涂层 冲蚀磨损 high velocity Oxy-Fuel Cr3C2-NiCr coating erosion wear
  • 相关文献

参考文献7

  • 1Picas J A,Forna A,Matth haus G.HVOF coatings as an alternative to hard chrome for pistons and valves[J].Wear,2006,216(5-6):477-484.
  • 2纪岗昌,李长久,王豫跃,圆田启嗣.喷涂工艺条件对超音速火焰喷涂Cr_3C_2-NiCr涂层冲蚀磨损性能的影响[J].摩擦学学报,2002,22(6):424-429. 被引量:35
  • 3纪岗昌.超音速火焰喷涂Cr3C2-NiCr涂层组织结构与性能的研究[D].西安:西安交通大学,2003.
  • 4蔡江,魏伟,王海军.超音速等离子喷涂WC-Co涂层的冲蚀磨损机理研究[J].有色金属(冶炼部分),2006(z1):57-61. 被引量:6
  • 5Aoh Jon-ning,Jeng Yau-ren,Chu En-lo,et al.On the wear behavior of surface clad layers under high temperature[J].Wear,1999:1114-11221.
  • 6Aoh Jon-ning,Chen Jian-cheng.On the wear characteristics of cobalt base hard facing layer after thermal fatigue and Oxidation[J].Wear,2001:61-6201.
  • 7Laugscheider E,Fischer A,Parco M,et al.High energy ball prepared Al2O3-NiCr dispersion powders for thermal spray coating[C].The 5th International Thermal Spraying Seminar ITSS' 2002:126-130.

二级参考文献18

  • 1[3]LIU Yourong,Traugott E,Fischer,et al.Comparison of HVOF and plasma-sprayed alumina/titania coatings microstructure,mechanical properties and abrasion behavior[J].Surface and Coatings Technology,2003,167(7):68-76.
  • 2Xu Binshi (徐滨士),Li Changjiu (李长久). Application and evolution of thermal spray technology(热喷涂技术的应用与发展)[C]. Beijing(北京): 8th National Welding Congress(第八届全国焊接会议论文集),1997. 149-155.
  • 3Beczkowiak J,Fischer J, Kellerer H, et al. Advanced carbides and borides for wear resistant coatings properties[C]. In: Proc of ITSC'95, Ohmori A eds. Kobe, Japan, 1995.1 033-1 057.
  • 4Lugscheider E, Remer P, Herbst C,et al. NiCr-Cr3C2 and NiCr-TiC high wear resistant coatings for protective applications in steam turbines[C]. In: Proc of the 14th ITSC, Ohmori A eds. Kobe, Japan, 1995. 235-240.
  • 5Fukuda Y, Kumon M. Application of high velocity flame spraying for the heat exchanger tubes in coal fired boilers[C].In: Proc of the 14th ITSC, Kobe, Japan, 1995. 107-110.
  • 6Wang Buqian. The erosion-corrosion behaviors of thermal sprayed coatings in fluidized bed combustor systems, Surface Modification Technologies[M]. Sudarsham T S, Khor K K, Jeandin M eds. Institute of Materials, London, 1997. 265-279.
  • 7Srinibasa Rao D, Sen D, Somaraju K R C, et al. Influence of powder particle velocity and temperature on the properties of Cr3C2-NiCr coating obtained by detonation-gun[C]. In: Proc of ITSC'98, Berndt C C eds. Nice, France, 1998. 385-393.
  • 8Crawmer D C, Krebsbach J D, Riggs W L. Coating development for HVOF process using design of experiment[C]. In: Proc of 13th ITSC, Berndt C C eds. Orlando, Florida, USA, 1992. 127-135.
  • 9Vuoristo P, Niemi K, Makela A, et al. Abrasion and erosion wear resistance of Cr3C2-NiCr coatings prepared by detonation and high velocity oxy-fuel spraying[C]. In: Proc of the 7th National Thermal Spray Conference. Berndt C C, Sampath S eds. Boston, Massachusetts, 1994. 124-126.
  • 10Wang B Q. The Dependence of erosion-corrosion wastage on carbide/metal binder proportion for HVOF carbide-metal cermet coatings[J]. Wear, 1996, 196: 141-146,

共引文献39

同被引文献38

  • 1高原,徐晋勇,刘燕萍,王建忠,隗晓云,徐重.不锈钢表面等离子复合处理提高耐磨性的研究[J].金属热处理,2005,30(7):50-53. 被引量:7
  • 2高荣发.热喷涂[M].北京:化学工业出版社,1992.93-95.
  • 3陈启文.煤化工工艺[M].化学工业出版社,2009.
  • 4Jiang X. L. Plasrna Spray Forming or Nanostructured Composed Coatings[ J]. Journal of Materials Scient e Technology; 2002. 18 (3) : 287-288.
  • 5Zeng Y. Lee S W. Ding C X. Plasma spray coatings ill different Nanosize alumina [J]. Matrials l eners , 2002, 57 (2) : 495-501.
  • 6栗桔,杨耀华.等离子喷涂和燃烧火焰喷涂技术[M].北京:国防工业出版社,1984.
  • 7Anh J. Jcng Y. Chu 1':, el al. On the wear behav ior or surface dad layers under high lellll'eralure [J]. Wear, 1999,225(2):1114-1121.
  • 8Aoh J, Chen J. On the wear characteristics or cobalt hasp hard lacing layer afterthennal fatigue and Oxidation [J]. Wear, 200 I ? 250:6 11-620.
  • 9陆培文.实用阀门没计手册[M].机械工业出版社,2002.
  • 10陶翀,王志勤,李云刚.冷轧辊超音速喷涂WC-12Co涂层的组织与性能研究[J].热加工工艺,2010,39(16):117-119. 被引量:7

引证文献7

二级引证文献28

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部