期刊文献+

气浮十字梁系统的气动-质量矩复合控制研究 被引量:1

Research on the Composite Control of Aerodynamics-Mass Moment Control over Gas-Floating Crossbeam Experiment System
在线阅读 下载PDF
导出
摘要 推导了基于气动-质量矩复合控制的气浮十字梁三自由度运动动力学方程,对纵向运动模型进行了数学仿真和实物实验。通过数学仿真和实物实验的比较,验证了建立模型的准确性,并对共栖效应现象进行了研究,为深入探讨气动-质量矩复合控制奠定了基础。 In this paper, the three degrees of freedom dynamic equations of gas-floating crossbeam based on composite control of aerodynamics-mass moment are derived for the first time. And a kind of simulation and practicality experiment about the crossbeam attitude confined to vertical plane is performed, the precision of this model is validated and the commensalism phenomenon is studied, which lays a foundation for developing the composite control of aerodynamics-mass moment.
出处 《飞行力学》 CSCD 北大核心 2008年第4期35-38,共4页 Flight Dynamics
基金 总装备部预研重点基金资助项目(6140511)
关键词 气动-质量矩复合控制 模型 共栖 十字梁 composite control of aerodynamics-mass moment control model commensalism phenomenon crossbeam
  • 相关文献

参考文献5

二级参考文献23

  • 1顾文锦,张汝川,于进勇.基于NBF网络的导弹航向平面滑模控制导引一体化[J].海军航空工程学院学报,2006,21(5):510-512. 被引量:4
  • 2施建洪,徐胜红,禹继顺.基于模糊理论的碟形飞行器复合控制分配策略[J].海军航空工程学院学报,2005,20(5):513-516. 被引量:7
  • 3钱杏芳 张鸿端 等.导弹飞行力学[M].北京:北京工业学院出版社,1987..
  • 4[1]Byrne R H, Robinett R D, et al. Moving Mass Trim Control Design. AIAA-96-3826
  • 5[2]Regan F J, Kavetsky R A. Add-On Controller for Ballistic Reentry Vehicles. U.S. Patent: Serial No.752.766, 1984
  • 6[3]Thomas Petsopoulos, Regan F J. Moving-Mass Roll Control System for Fixed-Trim Re-Entry Vehicle. Journal of Spacecraft and Rocket, 1996, 33 (1) : 54~60
  • 7[4]Kontis K, Qin N, Stollery J L. Hypersonic Performance of a Lifting Elliptic Cone with and without Strakes. Journal of Spacecraft and Rocket, 2000, 37 (1) : 21~27
  • 8[1]Bronstein J L.Our understanding of mutualism[J].The Quarterly of Biology,1994,69:31-51.
  • 9[2]Stiling.Introductory Ecology[D].New York:Prentice Hall,1992.
  • 10[3]Molles.Ecology[M].Beijing:Education Press,2002:23-34.

共引文献35

同被引文献11

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部