期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
Laboratory Research on Tahe AR Fluid Coking on Weak Acid Catalysts 被引量:1
1
作者 Wu Zhiguo Li Yanjun shen haiping(sinopec research institute of petroleum processing,beijing 100083) 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2011年第2期9-13,共5页
Fluid coking on micro-spherical particles with acid sites on them could produce more light oils from Tahe AR.The conversion rate could increase by about 20% on the catalyst B compared to that obtained on the catalyst ... Fluid coking on micro-spherical particles with acid sites on them could produce more light oils from Tahe AR.The conversion rate could increase by about 20% on the catalyst B compared to that obtained on the catalyst A and the light oil yield could increase by about 12%.The yield of gasoline and diesel was more than 50% from Tahe AR over the catalyst B.Tests on acidity of the catalyst B by pyridine FT-IR spectrometry showed that the total acid content and the ratio of weak acid number to total acid number were higher than other catalysts. 展开更多
关键词 fluid coking weak acid catalyst fixed fluidized bed Tahe AR
在线阅读 下载PDF
煅后石油焦石墨化度计算的修正方法研究 被引量:1
2
作者 施洋 范启明 +2 位作者 刘自宾 阎龙 申海平 《石油炼制与化工》 CAS CSCD 北大核心 2022年第4期89-94,共6页
石油焦石墨化度的计算最常用的是Mering-Maire方法,其使用前提是炭素材料的(002)晶面间距d_(002)≤0.3440 nm。煅后石油焦尚未石墨化,因而d_(002)较大。若d_(002)>0.3440 nm,将无法采用该方法对煅后石油焦的石墨化度进行估算。针对... 石油焦石墨化度的计算最常用的是Mering-Maire方法,其使用前提是炭素材料的(002)晶面间距d_(002)≤0.3440 nm。煅后石油焦尚未石墨化,因而d_(002)较大。若d_(002)>0.3440 nm,将无法采用该方法对煅后石油焦的石墨化度进行估算。针对该问题,提出由B值代替Mering-Maire式中d_(max)=0.3440 nm的思路,并以该方法计算得到3种d_(002)>0.3440 nm的煅后焦A,B,C的石墨化度分别为25.29%,24.58%,22.29%。该石油焦石墨化度计算修正方法与Mering-Maire方法能够较好地吻合。 展开更多
关键词 晶面间距 石墨化度 Mering-Maire公式 B值法
在线阅读 下载PDF
氢气预处理降低钒对渣油接触裂化反应影响的初步研究
3
作者 任磊 李延军 +2 位作者 李子锋 王勇 申海平 《炼油技术与工程》 CAS 2021年第4期1-5,共5页
在固定流化床试验装置上开展了氢气预处理钒含量不同的接触剂对渣油接触裂化反应性能的影响研究。研究结果表明,污染接触剂上钒含量的增加促进了新晶相的生成,导致接触剂的结构发生变化,当钒质量分数达4.59%时,接触剂孔结构变化明显而... 在固定流化床试验装置上开展了氢气预处理钒含量不同的接触剂对渣油接触裂化反应性能的影响研究。研究结果表明,污染接触剂上钒含量的增加促进了新晶相的生成,导致接触剂的结构发生变化,当钒质量分数达4.59%时,接触剂孔结构变化明显而且有明显莫来石相生成。与空白剂相比,钒污染促进渣油接触裂化反应过程中干气和焦炭的生成,导致生氢因子的增加。氢气预处理可以降低渣油接触裂化反应干气和焦炭的产率,提高液体收率,降低钒污染接触剂的脱氢活性和热裂化指数,当钒质量分数为3.54%时,较氢气预处理前,液体收率增加13百分点,生氢因子从5.48降到3.69,热裂化指数从39.73降到32.19。 展开更多
关键词 渣油 接触裂化 钒污染剂 氢气预处理
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部