(Mg,Fe)SiO_(3) is primarily located in the mantle and has a substantial impact on geophysical and geochemical processes.Here,we employ molecular dynamics simulations to investigate the structural and transport propert...(Mg,Fe)SiO_(3) is primarily located in the mantle and has a substantial impact on geophysical and geochemical processes.Here,we employ molecular dynamics simulations to investigate the structural and transport properties of(Mg,Fe)SiO_(3) with varying iron contents at temperatures up to 5000 K and pressures up to 135 GPa.We thoroughly examine the effects of pressure,temperature,and iron content on the bond lengths,coordination numbers,viscosities,and electrical conductivities of(Mg,Fe)SiO_(3).Our calculations indicate that the increase of pressure leads to the shortening of the O-O and Mg-O bond lengths,while the Si-O bond lengths exhibit the initial increase with pressure up to 40 GPa,after which they are almost unchanged.The coordination numbers of Si transition from four-fold to six-fold and eventually reach eight-fold coordination at 135 GPa.The enhanced pressure causes the decrease of the diffusion coefficients and the increase of the viscosities of(Mg,Fe)SiO_(3).The increased temperatures slightly decrease the coordination numbers and viscosities,as well as obviously increase the diffusion coefficients and electrical conductivities of(Mg,Fe)SiO_(3).Additionally,iron doping facilitates the diffusion of Si and O,reduces the viscosities,and enhances the electrical conductivities of(Mg,Fe)SiO_(3).These findings advance fundamental understanding of the structural and transport properties of(Mg,Fe)SiO_(3) under high temperature and high pressure,which provide novel insights for unraveling the complexities of geological processes within the Earth's mantle.展开更多
Oil and gas exploration studies have been increasingly moving deeper into the earth.The rocks in deep and ultra-deep reservoirs are exposed to a complex environment of high temperatures and large geo-stresses.The Tari...Oil and gas exploration studies have been increasingly moving deeper into the earth.The rocks in deep and ultra-deep reservoirs are exposed to a complex environment of high temperatures and large geo-stresses.The Tarim oilfield in the Xinjiang Uygur Autonomous Region(Xinjiang for short),China,has achieved a breakthrough in the exploration of deep hydrocarbon reservoirs at a depth of over 9000 m.The mechanical properties of deep rocks are significantly different from those of shallow rocks.In this study,triaxial compression tests were conducted on heat-treated carbonatite rocks to explore the evolution of the mechanical properties of carbonatite rocks under high confining pressure after thermal treatment.The rocks for the tests were collected from reservoirs in the Tarim oilfield,Xinjiang,China.The experiments were performed at confining pressures ranging from atmospheric to 120 MPa and temperatures ranging from25 to 500°C.The results show that the critical confining pressure of the brittle–ductile transition increases with increasing temperature.Young's modulus is negatively correlated with the temperature and positively correlated with the confining pressure.As the confining pressure increases,the failure mode of the specimens gradually transforms from shear fracture failure into“V”-type failure and finally into bulging failure(multiple shear fractures).With increasing temperature,the failure angle tends to decrease.In addition,an improved version of the Mohr-Coulomb strength criterion with a temperature-dependent power function was proposed to describe the failure strength of carbonatite rocks after exposure to high temperature and high confining pressure.The surface of the strength envelope of this criterion is temperature dependent,which could reflect the strength evolution of rock under high confining pressures after thermal treatment.Compared with other strength criteria,this criterion is more capable of replicating physical processes.展开更多
Molybdenum nitride,renowned for its exceptional physical and chemical properties,has garnered extensive attention and research interest.In this study,we employed first-principles calculations and the CALYPSO structure...Molybdenum nitride,renowned for its exceptional physical and chemical properties,has garnered extensive attention and research interest.In this study,we employed first-principles calculations and the CALYPSO structure prediction method to conduct a comprehensive analysis of the crystal structures and electronic properties of molybdenum nitride(Mo_(x)N_(1-x))under high pressure.We discovered two novel high-pressure phases:Imm2-MoN_(3) and Cmmm-MoN_(4),and confirmed their stability through the analysis of elastic constants and phonon dispersion curves.Notably,the MoN_(4) phase,with its high Vickers hardness of 36.9 GPa,demonstrates potential as a hard material.The results of this study have broadened the range of known high-pressure phases of molybdenum nitride,providing the groundwork for future theoretical and experimental researches.展开更多
Using natural gas(NG)as the primary fuel helps alleviate the fossil fuel crisis while reducing engine soot and nitrogen oxide(NO_(X))emissions.In this paper,the influences of a novel split injection concept on an NG h...Using natural gas(NG)as the primary fuel helps alleviate the fossil fuel crisis while reducing engine soot and nitrogen oxide(NO_(X))emissions.In this paper,the influences of a novel split injection concept on an NG high pressure direct injection(HPDI)engine are examined.Four typical split injection strategies,namely split pre-injection of pilot diesel(PD)and NG,split post-injection of PD and NG,split pre-injection of NG,and split post-injection of PD,were developed to investigate the influences on combustion and emissions.Results revealed that split pre injection of NG enhanced the atomization of PD,whereas the split post-injection of NG lowered the temperature in the core region of the PD spray,resulting in the deterioration of combustion.The effect of the split injection strategy on indicated thermal efficiency exceeded 7.5%.Split pre-injection was favorable to enhancing thermal efficiency,whereas split post-injection was not.Ignition delay,combustion duration,and premixed combustion time proportion were affected by injection strategies by 3.8%,50%,and 19.7%,respectively.Split pre-injection increased CH_(4) emission in the exhaust.Split post-injection,especially split post-injection of PD and NG,reduced the unburned CH_(4) emission by approximately 30%.When the split post-injection ratio was less than 30%,the trade-off between NO_(X) and soot was interrupted.The distribution range of hydroxyl radicals was expanded by pre-injection,and NO_(X) was generated in the region where the NG jet hit the wall.This paper provides valuable insights into the optimization of HPDI injection parameters.展开更多
Cubic boron nitride and hexagonal boron nitride are the two predominant crystalline structures of boron nitride.They can interconvert under varying pressure and temperature conditions.However,this transformation requi...Cubic boron nitride and hexagonal boron nitride are the two predominant crystalline structures of boron nitride.They can interconvert under varying pressure and temperature conditions.However,this transformation requires overcoming significant potential barriers in dynamics,which poses great difficulty in determining the c-BN/h-BN phase boundary.This study used high-pressure in situ differential thermal measurements to ascertain the temperature of h-BN/c-BN conversion within the commonly used pressure range(3-6 GPa)for the industrial synthesis of c-BN to constrain the P-T phase boundary of h-BN/c-BN in the pressure-temperature range as much as possible.Based on the analysis of the experimental data,it is determined that the relationship between pressure and temperature conforms to the following equation:P=a+1/bT.Here,P denotes the pressure(GPa)and T is the temperature(K).The coefficients are a=-3.8±0.8 GPa and b=229.8±17.1 GPa/K.These findings call into question existing high-pressure and high-temperature phase diagrams of boron nitride,which seem to overstate the phase boundary temperature between c-BN and h-BN.The BN phase diagram obtained from this study can provide critical temperature and pressure condition guidance for the industrial synthesis of c-BN,thus optimizing synthesis efficiency and product performance.展开更多
Enzymatic hydrolysis of proteins can enhance their emulsifying properties and antioxidant activities.However,the problem related to the hydrolysis of proteins was the generation of the bitter taste.Recently,high hydro...Enzymatic hydrolysis of proteins can enhance their emulsifying properties and antioxidant activities.However,the problem related to the hydrolysis of proteins was the generation of the bitter taste.Recently,high hydrostatic pressure(HHP)treatment has attracted much interest and has been used in several studies on protein modification.Hence,the study aimed to investigate the effects of enzymatic hydrolysis by Corolase PP under different pressure treatments(0.1,100,200,and 300 MPa for 1-5 h at 50℃)on the emulsifying property,antioxidant activity,and bitterness of soybean protein isolate hydrolysate(SPIH).As observed,the hydrolysate obtained at 200 MPa for 4 h had the highest emulsifying activity index(47.49 m^(2)/g)and emulsifying stability index(92.98%),and it had higher antioxidant activities(44.77%DPPH free radical scavenging activity,31.12%superoxide anion radical scavenging activity,and 61.50%copper ion chelating activity).At the same time,the enhancement of emulsion stability was related to the increase of zeta potential and the decrease of mean particle size.In addition,the hydrolysate obtained at 200 MPa for 4 h had a lower bitterness value and showed better palatability.This study has a broad application prospect in developing food ingredients and healthy foods.展开更多
The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron mi...The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).展开更多
Mn_(3)TeO_(6)(MTO) has been experimentally found to adopt a P2_(1)/In structure under high pressure,which exhibits a significantly smaller band gap compared to the atmospheric R3 phase.In this study,we systematically ...Mn_(3)TeO_(6)(MTO) has been experimentally found to adopt a P2_(1)/In structure under high pressure,which exhibits a significantly smaller band gap compared to the atmospheric R3 phase.In this study,we systematically investigate the magnetism,structural phase transition,and electronic properties of MTO under high pressure through first-principles calculations.Both R3 and P2_(1)/n phases of MTO are antiferromagnetic at zero temperature.The R3 phase transforms to the P2_(1)/n phase at 7.5 8 GPa,accompanied by a considerable volume collapse of about 6.47%.Employing the accurate method that combines DFT+U/and GW,the calculated band gap of R3 phase at zero pressure is very close to the experimental values,while that of the P2_(1)/n phase is significantly overestimated.The main reason for this difference is that the experimental study incorrectly used the Kubelka-Munk plot for the indirect band gap to obtain the band gap of the P2_(1)/n phase instead of the Kubelka-Munk plot for the direct band gap.Furthermore,our study reveals that the transition from the R3 phase to the P2_(1)/n phase is accompanied by a slight reduction in the band gap.展开更多
Boron phosphide(BP)has gained significant research attention due to its unique photoelectric and mechanical properties.In this work,we investigated the stability of BP under high pressure using x-ray diffraction and s...Boron phosphide(BP)has gained significant research attention due to its unique photoelectric and mechanical properties.In this work,we investigated the stability of BP under high pressure using x-ray diffraction and scanning electron microscope.The phase diagram of BP was explored in both B-rich and P-rich environments,revealing crucial insight into its behavior at 5.0 GPa.Additionally,we measured the melting curve of BP from 8.0 GPa to 15.0 GPa.Our findings indicate that the stability of BP under high pressure is improved within B-rich and P-rich environments.Furthermore,we report a remarkable observation of melting curve frustration at 10.0 GPa.This study will enhance our understanding of stability of BP under high pressure,shedding light on its potential application in semiconductor,thermal,and light-transmitting devices.展开更多
The group V–VI semiconductor material getchellite (crystalline AsSbS_(3)) has garnered extensive attention due to itswonderful electronic and optical properties. The pressure engineering is one of the most effective ...The group V–VI semiconductor material getchellite (crystalline AsSbS_(3)) has garnered extensive attention due to itswonderful electronic and optical properties. The pressure engineering is one of the most effective methods to modulatecrystal structure and physical properties of semiconductor materials. In this study, the structural behavior, optical and electricalproperties of AsSbS_(3) under high pressure have been investigated systematically by in situ high-pressure experimentsfor the first time. The monoclinic structure of AsSbS_(3) remains stable up to 47.0 GPa without phase transition. The graduallattice contraction with increasing pressure results in a continuous narrowing of the bandgap then leads to pressure-inducedmetallization of AsSbS_(3) at 31.5 GPa. Our research presents a high-pressure strategy for tuning the crystal structure andphysical properties of AsSbS_(3) to expand its potential applications in electronic and optoelectronic fields.展开更多
AIM:To understand the molecular connectivity between the intraocular pressure(IOP)and glaucoma which will provide possible clues for biomarker candidates.METHODS:The current study uncovers the important genes connecti...AIM:To understand the molecular connectivity between the intraocular pressure(IOP)and glaucoma which will provide possible clues for biomarker candidates.METHODS:The current study uncovers the important genes connecting IOP with the core functional modules of glaucoma.An integrated analysis was performed using glaucoma and IOP microarray datasets to screen for differentially expressed genes(DEGs)in both conditions.To the selected DEGs,the protein interaction network was constructed and dissected to determine the core functional clusters of glaucoma.For the clusters,the connectivity of IOP DEGs was determined.Further,enrichment analyses were performed to assess the functional annotation and potential pathways of the crucial clusters.RESULTS:The gene expression analysis of glaucoma and IOP with normal control showed that 408 DEGs(277 glaucoma and 131 IOP genes)were discovered from two GEO datasets.The 290 DEGs of glaucoma were extended to form a network containing 1495 proteins with 9462 edges.Using ClusterONE,the network was dissected to have 12 clusters.Among them,three clusters were linked with three IOP DEGs[N-Myc and STAT Interactor(NMI),POLR3G(RNA Polymerase Ⅲ Subunit G),and APAF1-interacting protein(APIP)].In the clusters,ontology analysis revealed that RNA processing and transport,p53 class mediators resulting in cell cycle arrest,cellular response to cytokine stimulus,regulation of phosphorylation,regulation of type Ⅰ interferon production,DNA deamination,and cellular response to hypoxia were significantly enriched to be implicated in the development of glaucoma.Finally,NMI,POLR3G,and APIP may have roles that were noticed altered in glaucoma and IOP conditions.CONCLUSION:Our findings could help to discover new potential biomarkers,elucidate the underlying pathophysiology,and identify new therapeutic targets for glaucoma.展开更多
Al and Mg alloy high pressure die castings(HPDC)are increasingly used in automotive industries.The microstructures in the castings have decisive effect on the casting mechanical properties,in which the microstructure ...Al and Mg alloy high pressure die castings(HPDC)are increasingly used in automotive industries.The microstructures in the castings have decisive effect on the casting mechanical properties,in which the microstructure characteristics are fundamental for the investigation of the microstructure-property relation.During the past decade,the microstructure characteristics of HPDC Al and Mg alloys,especially micro-pores andα-Fe,have been investigated from two-dimensional(2D)to threedimensional with X-ray micro-computed tomography(μ-CT).This paper provides an overview of the current understanding regarding the 3D characteristics and formation mechanisms of microstructures in HPDC alloys,their spatial distributions,and the impact on mechanical properties.Additionally,it outlines future research directions for the formation and control of heterogeneous microstructures in HPDC alloys.展开更多
The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the crit...The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the critical state,and this is not mature for intermediate artificial soils(tailings)in a broad range of confining pressures.In this paper,it aims to describe the behaviour of iron ore tailings in a spectrum of confining pressures broader than the reported in previous studies.A series of consolidated drained(CD)triaxial tests was carried out with confining pressures ranging from 0.075 MPa to 120 MPa.These results show that the amount of breakage plays an essential role in the response of iron ore tailings.The existence of curved critical state line(CSL)in both specific volume(ν)-logarithm of mean effective stress(p′)and deviatoric stress(q)-mean effective stress(p′)planes,and different responses in the deviatoric stress-axial strain-volumetric strain curves were verified.An inverse S-shaped equation was proposed to represent the silty-sandy tailings'behaviour up to high pressures onν-lnp′plane.The proposed equation provides a basis for enhancing constitutive models and considers the evolution of the grading up to severe loading conditions.The adjustment considered three regions with different responses associated with particle breakage at different pressure levels.展开更多
This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by...This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.展开更多
Context/Objective: High blood pressure (HBP) currently represents the most widespread chronic non-communicable disease in Cameroon. The increase in its prevalence in the country is the result of multiple factors inclu...Context/Objective: High blood pressure (HBP) currently represents the most widespread chronic non-communicable disease in Cameroon. The increase in its prevalence in the country is the result of multiple factors including economic stress imposed by precariousness, poor living conditions, sources of anxiety, anguish, depression and other behavioral disorders. Economic stress is a globalizing concept that integrates into a purely hermeneutic approach, a particular functioning of the nervous system of an individual who faces employment problems and precarious remuneration conditions. The non-satisfaction by an individual of his basic needs due to insufficient financial means can cause him to become irritable, aggressive, and socially and symbolically isolated, thereby increasing the desire to resort to morbid life models such as excessive consumption of narcotics and other psychoactive substances often associated with high blood pressure. The fight against the emergence of BPH is a complex, multifaceted and multifactorial reality that requires taking into account economic stress. The main objective of this survey is to describe the situation of economic stress within the Cameroonian population, which imposes precariousness and life models at risk of high blood pressure. Specifically, we determined the level of household income and the sources of income. Methods: A cross-sectional survey with a descriptive aim among five hundred households in the Central Region of Cameroon was conducted. A probabilistic technique called simple randomness was used. The number of households to be surveyed was determined indirectly using the Cochrane formula. Data collection in face-to-face mode using a physical questionnaire took place from July 1 to August 31, 2023, after obtaining ethical clearance from the Regional Health Research Ethics Committee, Human from the Center and an administrative authorization for data collection. Regarding their processing, the data was grouped during processing in Excel sheets. Normality and reliability tests of the collected data were carried out. For this, the Chi-square test was used for data with a qualitative value and that of Kolmogorov-Sminorf for data with a quantitative value. Descriptive analysis was possible using R software version 3.2, SPSS version 25.0, XLSTAT 2016, PAST and EXCEL programs from Microsoft Office 2013. Results: The main results highlight economic stress, with 45.60% of households surveyed earning less than US$154 per month;55% of household heads were women in single-parent families;14% of household heads were unemployed, 22% worked in the private sector and 19% were self-employed. This general economic situation leads to precarious living conditions, thereby increasing the risk of high blood pressure among the Cameroonian population.展开更多
Context/objectives: The fight against Chronic Non-Communicable Diseases (NCDs) is a long-term undertaking, which requires available, motivated and well-managed human resources (HR). The administrative management of sk...Context/objectives: The fight against Chronic Non-Communicable Diseases (NCDs) is a long-term undertaking, which requires available, motivated and well-managed human resources (HR). The administrative management of skills on both qualitative and quantitative levels is one of the essential functions of a health system. To better implement policies of fight against High Blood Pressure (HBP) and other chronic diseases, it is important to establish strategies to retain health personnel. This loyalty requires favorable working conditions and consideration of the contribution-reward couple. Good working conditions are likely to reduce the phenomenon of medical nomadism;conversely, poor HR management can contribute to their exodus towards exotic “green pastures”, thus leading to an additional crisis in the Cameroonian health system. The fight against HBP is a complex, multifaceted and multifactorial reality that requires appropriate management model for all types of resources mainly HR. The main objective of this research is to show the impact of poor management of human resources in Cameroon health system on medical nomadism and the ineffectiveness of the fight against High Blood Pressure. Method: A cross-sectional descriptive survey among five hundred (500) health facilities in the center region of Cameroon has been conducted. A stratified probabilistic technique has been used, and the number of health facilities to be surveyed has been determined using the “sample size estimation table” of Depelteau. The physical questionnaires have been printed and then distributed to data collectors. After data collection, the latter were grouped during processing in Excel sheets. The Chi-square test was used for data with a qualitative value and that of Kolmogorov-Sminorf for data with a quantitative value to assess the normality and reliability of data. The Crochach’s Alpha reliability test allowed us to have a summary of the means and variances and then to search for intragroup correlations between variables. Descriptive analysis was possible with the XLSTAT 2016 software. Results: 43.60% of Health Facilities (HF) managers were unqualified. 82.20% of HF managers have staff in a situation of professional insecurity. They are mainly contractual (49.00), decision-making agents (24.40%), casual agents (08.80). The proportion of unstable personnel is average of 22.00% and very unstable, 12.00%.展开更多
Introduction: High blood pressure is defined as blood pressure greater than or equal to 140 mm Hg for systolic and or 90 mm Hg for diastolic. It constitutes a major public health problem, the leading chronic disease i...Introduction: High blood pressure is defined as blood pressure greater than or equal to 140 mm Hg for systolic and or 90 mm Hg for diastolic. It constitutes a major public health problem, the leading chronic disease in the world. The objective was to determine the prevalence, treatment rate and control of hypertension. Methods: This was a cross-sectional and descriptive study which took place over a period of 6 months in a hospital environment and in the general population. Results: Of the 1000 participants, 637 had hypertension, giving a prevalence of 63.70% with a female predominance. Thirty-three percent (33%) were unaware of their high blood pressure. The age group 60 and more was the most represented (44%). A proportion of 33 and 23.20 were overweight and obese participants, respectively. Male subjects were more overweight than female, unlike obesity which was more common among female subjects. Sixty-two percent (62%) of hypertensives were treated, of whom 44% were non-compliant. The excessively high cost and consumption of medications as needed were the main factors in therapeutic non-compliance. Twenty-two percent (22%) of all hypertensive patients and 35% of treated hypertensive patients were controlled. Women were more treated but less observant and less controlled than men. Therapeutic coverage and combination therapy rates were lower in rural areas. Hypertensives who had a high level of education were better treated and controlled than those who had no level. Conclusion: High blood pressure remains a real public health problem in Mali. It is more common in people aged 60 and over and in females. One in three hypertensives were unaware of their hypertension. The majority received antihypertensive treatments, but only a minority of them had their hypertension controlled.展开更多
The large water transfer channels has a total length of more than 1000 km,spanning across the Huaihe River,the Yangtze River,the Yellow River and the Haihe River basins.During the preliminary design stage,the groundwa...The large water transfer channels has a total length of more than 1000 km,spanning across the Huaihe River,the Yangtze River,the Yellow River and the Haihe River basins.During the preliminary design stage,the groundwater level was predicted based on the initial water level plus the groundwater level increase by precipitation infiltration and recharge in 1956 and 1996.However,after the rainfall in 2021 and 2023 to infiltrate and recharge groundwater,it is necessary to re-forecast the groundwater level.The Hebei section was taken as an example.Combined with the actual measurement of the historical maximum water level of the monitoring section and the inspection along the line,the water seepage of the canal slope was found.It is necessary to investigate the drainage system of the high groundwater level canal sections,take necessary treatment measures to improve the ability of the drainage system to cope with the rapid rise of high groundwater caused by heavy rainfall,and strengthen drainage measures for the risk parts of project safety in the high groundwater level canal sections,which are essential to ensure the safe operation of the middle route of the large water transfer channels.展开更多
Based on the principle of transient perturbation analysis,in this paper,a method to objectively determine the weather pattern formed by sea fog is provided.On the basis of the classification results,the circulation si...Based on the principle of transient perturbation analysis,in this paper,a method to objectively determine the weather pattern formed by sea fog is provided.On the basis of the classification results,the circulation situation,divergence and vertical velocity field,and the vertical profile of temperature and humidity are synthesized and analyzed.The basic characteristics of the circulation and physical field of sea fog under low pressure control(L type sea fog)are obtained,and the results are compared with the sea fog under the control of high pressure(H type sea fog):a)L type sea fogs potential height anomaly disturbance is mainly manifested in the low layer,and its average value is-65.66 gpm,gradually weakening upward;b)L type sea fogs inversion structure is weaker than H type sea fogs when it occurs,the fog layer is thicker and the high relative humidity level is high over the fog layer,while the H type sea fogs fog layer has a relatively obvious dry layer;c)L sea fog has three layers of structure at the vertical direction.The first layer 1000-950 hPa is convergence accompanied by weak rise and subsidence,the second layer 950-850 hPa is divergence accompanied by weak subsidence,and the third layer 850 to 500hPa is gradually strengthened.While there are two layer structures of the H type sea fog.1000 hPa is divergence accompanied by weak rising and sinking movement,950-500 hPa is a uniform subsidence movement.d)Probability density statistical analysis further quantified the vertical movement of L and H type sea fog and the distribution of relative humidity in each layer.These conclusions provide an important reference for forecasting the sea fog in the northwest of the Yellow Sea under the condition of low pressure circulation in summer.展开更多
To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines...To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids （fresh water-based and brine-based） under high temperature and high pressure （HTHP） with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12174352 and 12111530103)the Fundamental Research Funds for the Central Universities,China University of Geosciences(Wuhan)(Grant No.G1323523065)。
文摘(Mg,Fe)SiO_(3) is primarily located in the mantle and has a substantial impact on geophysical and geochemical processes.Here,we employ molecular dynamics simulations to investigate the structural and transport properties of(Mg,Fe)SiO_(3) with varying iron contents at temperatures up to 5000 K and pressures up to 135 GPa.We thoroughly examine the effects of pressure,temperature,and iron content on the bond lengths,coordination numbers,viscosities,and electrical conductivities of(Mg,Fe)SiO_(3).Our calculations indicate that the increase of pressure leads to the shortening of the O-O and Mg-O bond lengths,while the Si-O bond lengths exhibit the initial increase with pressure up to 40 GPa,after which they are almost unchanged.The coordination numbers of Si transition from four-fold to six-fold and eventually reach eight-fold coordination at 135 GPa.The enhanced pressure causes the decrease of the diffusion coefficients and the increase of the viscosities of(Mg,Fe)SiO_(3).The increased temperatures slightly decrease the coordination numbers and viscosities,as well as obviously increase the diffusion coefficients and electrical conductivities of(Mg,Fe)SiO_(3).Additionally,iron doping facilitates the diffusion of Si and O,reduces the viscosities,and enhances the electrical conductivities of(Mg,Fe)SiO_(3).These findings advance fundamental understanding of the structural and transport properties of(Mg,Fe)SiO_(3) under high temperature and high pressure,which provide novel insights for unraveling the complexities of geological processes within the Earth's mantle.
基金National Natural Science Foundation of China,Grant/Award Number:52034010。
文摘Oil and gas exploration studies have been increasingly moving deeper into the earth.The rocks in deep and ultra-deep reservoirs are exposed to a complex environment of high temperatures and large geo-stresses.The Tarim oilfield in the Xinjiang Uygur Autonomous Region(Xinjiang for short),China,has achieved a breakthrough in the exploration of deep hydrocarbon reservoirs at a depth of over 9000 m.The mechanical properties of deep rocks are significantly different from those of shallow rocks.In this study,triaxial compression tests were conducted on heat-treated carbonatite rocks to explore the evolution of the mechanical properties of carbonatite rocks under high confining pressure after thermal treatment.The rocks for the tests were collected from reservoirs in the Tarim oilfield,Xinjiang,China.The experiments were performed at confining pressures ranging from atmospheric to 120 MPa and temperatures ranging from25 to 500°C.The results show that the critical confining pressure of the brittle–ductile transition increases with increasing temperature.Young's modulus is negatively correlated with the temperature and positively correlated with the confining pressure.As the confining pressure increases,the failure mode of the specimens gradually transforms from shear fracture failure into“V”-type failure and finally into bulging failure(multiple shear fractures).With increasing temperature,the failure angle tends to decrease.In addition,an improved version of the Mohr-Coulomb strength criterion with a temperature-dependent power function was proposed to describe the failure strength of carbonatite rocks after exposure to high temperature and high confining pressure.The surface of the strength envelope of this criterion is temperature dependent,which could reflect the strength evolution of rock under high confining pressures after thermal treatment.Compared with other strength criteria,this criterion is more capable of replicating physical processes.
基金Project supported by the National Natural Science Foundation of China(Grant No.11964026)the Natural Science Foundation of Inner Mongolia,China(Grant Nos.2019MS01010 and 2023LHMS01014)+4 种基金Higher Educational Scientific Research Projects of Inner Mongolia(Grant Nos.NJZZ19145 and NJZZ22470)the Educational Scientific Research Project of Liaoning Province(Grant No.LJKZ0452)the Doctoral Starting up Foundation of Inner Mongolia Minzu University of Science and Technology(Grant No.BSZ023)Inner Mongolia Autonomous Region Youth Capacity Improvement Project(Grant No.GXKY22157)Higher Physics Major Teaching Steering Committee of the Ministry of Education Project(Grant No.JZW-23-GT-21)。
文摘Molybdenum nitride,renowned for its exceptional physical and chemical properties,has garnered extensive attention and research interest.In this study,we employed first-principles calculations and the CALYPSO structure prediction method to conduct a comprehensive analysis of the crystal structures and electronic properties of molybdenum nitride(Mo_(x)N_(1-x))under high pressure.We discovered two novel high-pressure phases:Imm2-MoN_(3) and Cmmm-MoN_(4),and confirmed their stability through the analysis of elastic constants and phonon dispersion curves.Notably,the MoN_(4) phase,with its high Vickers hardness of 36.9 GPa,demonstrates potential as a hard material.The results of this study have broadened the range of known high-pressure phases of molybdenum nitride,providing the groundwork for future theoretical and experimental researches.
基金Supported by the National Natural Science Foundation of China(No.51909154)Shanghai Engineering Research Center of Ship Intelligent Maintenance and Energy Efficiency(No.20DZ2252300).
文摘Using natural gas(NG)as the primary fuel helps alleviate the fossil fuel crisis while reducing engine soot and nitrogen oxide(NO_(X))emissions.In this paper,the influences of a novel split injection concept on an NG high pressure direct injection(HPDI)engine are examined.Four typical split injection strategies,namely split pre-injection of pilot diesel(PD)and NG,split post-injection of PD and NG,split pre-injection of NG,and split post-injection of PD,were developed to investigate the influences on combustion and emissions.Results revealed that split pre injection of NG enhanced the atomization of PD,whereas the split post-injection of NG lowered the temperature in the core region of the PD spray,resulting in the deterioration of combustion.The effect of the split injection strategy on indicated thermal efficiency exceeded 7.5%.Split pre-injection was favorable to enhancing thermal efficiency,whereas split post-injection was not.Ignition delay,combustion duration,and premixed combustion time proportion were affected by injection strategies by 3.8%,50%,and 19.7%,respectively.Split pre-injection increased CH_(4) emission in the exhaust.Split post-injection,especially split post-injection of PD and NG,reduced the unburned CH_(4) emission by approximately 30%.When the split post-injection ratio was less than 30%,the trade-off between NO_(X) and soot was interrupted.The distribution range of hydroxyl radicals was expanded by pre-injection,and NO_(X) was generated in the region where the NG jet hit the wall.This paper provides valuable insights into the optimization of HPDI injection parameters.
基金supported by the National Key R&D Program of China(Grant No.2023YFA1406200).
文摘Cubic boron nitride and hexagonal boron nitride are the two predominant crystalline structures of boron nitride.They can interconvert under varying pressure and temperature conditions.However,this transformation requires overcoming significant potential barriers in dynamics,which poses great difficulty in determining the c-BN/h-BN phase boundary.This study used high-pressure in situ differential thermal measurements to ascertain the temperature of h-BN/c-BN conversion within the commonly used pressure range(3-6 GPa)for the industrial synthesis of c-BN to constrain the P-T phase boundary of h-BN/c-BN in the pressure-temperature range as much as possible.Based on the analysis of the experimental data,it is determined that the relationship between pressure and temperature conforms to the following equation:P=a+1/bT.Here,P denotes the pressure(GPa)and T is the temperature(K).The coefficients are a=-3.8±0.8 GPa and b=229.8±17.1 GPa/K.These findings call into question existing high-pressure and high-temperature phase diagrams of boron nitride,which seem to overstate the phase boundary temperature between c-BN and h-BN.The BN phase diagram obtained from this study can provide critical temperature and pressure condition guidance for the industrial synthesis of c-BN,thus optimizing synthesis efficiency and product performance.
基金supported by the Doctoral Research Foundation of Bohai University (05013/0520bs006)the Science and Technology Project of“Unveiling and Commanding”Liaoning Province (2021JH1/10400033)the Scientific Research Project from Education Department of Liaoning Province (LJ2020010)。
文摘Enzymatic hydrolysis of proteins can enhance their emulsifying properties and antioxidant activities.However,the problem related to the hydrolysis of proteins was the generation of the bitter taste.Recently,high hydrostatic pressure(HHP)treatment has attracted much interest and has been used in several studies on protein modification.Hence,the study aimed to investigate the effects of enzymatic hydrolysis by Corolase PP under different pressure treatments(0.1,100,200,and 300 MPa for 1-5 h at 50℃)on the emulsifying property,antioxidant activity,and bitterness of soybean protein isolate hydrolysate(SPIH).As observed,the hydrolysate obtained at 200 MPa for 4 h had the highest emulsifying activity index(47.49 m^(2)/g)and emulsifying stability index(92.98%),and it had higher antioxidant activities(44.77%DPPH free radical scavenging activity,31.12%superoxide anion radical scavenging activity,and 61.50%copper ion chelating activity).At the same time,the enhancement of emulsion stability was related to the increase of zeta potential and the decrease of mean particle size.In addition,the hydrolysate obtained at 200 MPa for 4 h had a lower bitterness value and showed better palatability.This study has a broad application prospect in developing food ingredients and healthy foods.
基金financially supported by the National Key Research and Development Program of China(2022YFB3404201)the Major Science and Technology Project of Changchun City,Jilin Province(Grant No.20210301024GX)。
文摘The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).
基金Project supported by National Key Research and Development Program of China(Grant No.2021YFB3802300)the Natural Science Foundation of China Academy of Engineering Physics(Grant Nos.U1730248 and U1830101)the National Natural Science Foundation of China(Grant Nos.12202418,11872056,11904282,12074274,and 12174356)。
文摘Mn_(3)TeO_(6)(MTO) has been experimentally found to adopt a P2_(1)/In structure under high pressure,which exhibits a significantly smaller band gap compared to the atmospheric R3 phase.In this study,we systematically investigate the magnetism,structural phase transition,and electronic properties of MTO under high pressure through first-principles calculations.Both R3 and P2_(1)/n phases of MTO are antiferromagnetic at zero temperature.The R3 phase transforms to the P2_(1)/n phase at 7.5 8 GPa,accompanied by a considerable volume collapse of about 6.47%.Employing the accurate method that combines DFT+U/and GW,the calculated band gap of R3 phase at zero pressure is very close to the experimental values,while that of the P2_(1)/n phase is significantly overestimated.The main reason for this difference is that the experimental study incorrectly used the Kubelka-Munk plot for the indirect band gap to obtain the band gap of the P2_(1)/n phase instead of the Kubelka-Munk plot for the direct band gap.Furthermore,our study reveals that the transition from the R3 phase to the P2_(1)/n phase is accompanied by a slight reduction in the band gap.
基金Project supported by the National Natural Science Foundation of China (Grant No.12074273)the Sichuan Science and Technology Program (Grant No.2022NSFSC1810)。
文摘Boron phosphide(BP)has gained significant research attention due to its unique photoelectric and mechanical properties.In this work,we investigated the stability of BP under high pressure using x-ray diffraction and scanning electron microscope.The phase diagram of BP was explored in both B-rich and P-rich environments,revealing crucial insight into its behavior at 5.0 GPa.Additionally,we measured the melting curve of BP from 8.0 GPa to 15.0 GPa.Our findings indicate that the stability of BP under high pressure is improved within B-rich and P-rich environments.Furthermore,we report a remarkable observation of melting curve frustration at 10.0 GPa.This study will enhance our understanding of stability of BP under high pressure,shedding light on its potential application in semiconductor,thermal,and light-transmitting devices.
基金Project supported by the National Natural Science Foundation of China(Grant No.42274123)the Special Construction Project Fund for Shandong Provincial Taishan Scholars.
文摘The group V–VI semiconductor material getchellite (crystalline AsSbS_(3)) has garnered extensive attention due to itswonderful electronic and optical properties. The pressure engineering is one of the most effective methods to modulatecrystal structure and physical properties of semiconductor materials. In this study, the structural behavior, optical and electricalproperties of AsSbS_(3) under high pressure have been investigated systematically by in situ high-pressure experimentsfor the first time. The monoclinic structure of AsSbS_(3) remains stable up to 47.0 GPa without phase transition. The graduallattice contraction with increasing pressure results in a continuous narrowing of the bandgap then leads to pressure-inducedmetallization of AsSbS_(3) at 31.5 GPa. Our research presents a high-pressure strategy for tuning the crystal structure andphysical properties of AsSbS_(3) to expand its potential applications in electronic and optoelectronic fields.
文摘AIM:To understand the molecular connectivity between the intraocular pressure(IOP)and glaucoma which will provide possible clues for biomarker candidates.METHODS:The current study uncovers the important genes connecting IOP with the core functional modules of glaucoma.An integrated analysis was performed using glaucoma and IOP microarray datasets to screen for differentially expressed genes(DEGs)in both conditions.To the selected DEGs,the protein interaction network was constructed and dissected to determine the core functional clusters of glaucoma.For the clusters,the connectivity of IOP DEGs was determined.Further,enrichment analyses were performed to assess the functional annotation and potential pathways of the crucial clusters.RESULTS:The gene expression analysis of glaucoma and IOP with normal control showed that 408 DEGs(277 glaucoma and 131 IOP genes)were discovered from two GEO datasets.The 290 DEGs of glaucoma were extended to form a network containing 1495 proteins with 9462 edges.Using ClusterONE,the network was dissected to have 12 clusters.Among them,three clusters were linked with three IOP DEGs[N-Myc and STAT Interactor(NMI),POLR3G(RNA Polymerase Ⅲ Subunit G),and APAF1-interacting protein(APIP)].In the clusters,ontology analysis revealed that RNA processing and transport,p53 class mediators resulting in cell cycle arrest,cellular response to cytokine stimulus,regulation of phosphorylation,regulation of type Ⅰ interferon production,DNA deamination,and cellular response to hypoxia were significantly enriched to be implicated in the development of glaucoma.Finally,NMI,POLR3G,and APIP may have roles that were noticed altered in glaucoma and IOP conditions.CONCLUSION:Our findings could help to discover new potential biomarkers,elucidate the underlying pathophysiology,and identify new therapeutic targets for glaucoma.
基金supported by the National Natural Science Foundation of China(Nos.51875211 and 51375171)Beijing Natural Science Foundation(No.L223001)+1 种基金Natural Science Foundation of Guangdong Province(No.2023A1515012730)the Program for New Century Excellent Talents in University in China(No.NCET-08-0209).
文摘Al and Mg alloy high pressure die castings(HPDC)are increasingly used in automotive industries.The microstructures in the castings have decisive effect on the casting mechanical properties,in which the microstructure characteristics are fundamental for the investigation of the microstructure-property relation.During the past decade,the microstructure characteristics of HPDC Al and Mg alloys,especially micro-pores andα-Fe,have been investigated from two-dimensional(2D)to threedimensional with X-ray micro-computed tomography(μ-CT).This paper provides an overview of the current understanding regarding the 3D characteristics and formation mechanisms of microstructures in HPDC alloys,their spatial distributions,and the impact on mechanical properties.Additionally,it outlines future research directions for the formation and control of heterogeneous microstructures in HPDC alloys.
文摘The disposal of filtered tailings in high dry stacks can induce particle breakage,changing the material's behaviour during the structure's lifetime.The grading changes influence material properties at the critical state,and this is not mature for intermediate artificial soils(tailings)in a broad range of confining pressures.In this paper,it aims to describe the behaviour of iron ore tailings in a spectrum of confining pressures broader than the reported in previous studies.A series of consolidated drained(CD)triaxial tests was carried out with confining pressures ranging from 0.075 MPa to 120 MPa.These results show that the amount of breakage plays an essential role in the response of iron ore tailings.The existence of curved critical state line(CSL)in both specific volume(ν)-logarithm of mean effective stress(p′)and deviatoric stress(q)-mean effective stress(p′)planes,and different responses in the deviatoric stress-axial strain-volumetric strain curves were verified.An inverse S-shaped equation was proposed to represent the silty-sandy tailings'behaviour up to high pressures onν-lnp′plane.The proposed equation provides a basis for enhancing constitutive models and considers the evolution of the grading up to severe loading conditions.The adjustment considered three regions with different responses associated with particle breakage at different pressure levels.
基金The research was funded by Science and Technology Project of Hebei Education Department(Project Number:QN2022198).Y.C.received the grant.
文摘This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.
文摘Context/Objective: High blood pressure (HBP) currently represents the most widespread chronic non-communicable disease in Cameroon. The increase in its prevalence in the country is the result of multiple factors including economic stress imposed by precariousness, poor living conditions, sources of anxiety, anguish, depression and other behavioral disorders. Economic stress is a globalizing concept that integrates into a purely hermeneutic approach, a particular functioning of the nervous system of an individual who faces employment problems and precarious remuneration conditions. The non-satisfaction by an individual of his basic needs due to insufficient financial means can cause him to become irritable, aggressive, and socially and symbolically isolated, thereby increasing the desire to resort to morbid life models such as excessive consumption of narcotics and other psychoactive substances often associated with high blood pressure. The fight against the emergence of BPH is a complex, multifaceted and multifactorial reality that requires taking into account economic stress. The main objective of this survey is to describe the situation of economic stress within the Cameroonian population, which imposes precariousness and life models at risk of high blood pressure. Specifically, we determined the level of household income and the sources of income. Methods: A cross-sectional survey with a descriptive aim among five hundred households in the Central Region of Cameroon was conducted. A probabilistic technique called simple randomness was used. The number of households to be surveyed was determined indirectly using the Cochrane formula. Data collection in face-to-face mode using a physical questionnaire took place from July 1 to August 31, 2023, after obtaining ethical clearance from the Regional Health Research Ethics Committee, Human from the Center and an administrative authorization for data collection. Regarding their processing, the data was grouped during processing in Excel sheets. Normality and reliability tests of the collected data were carried out. For this, the Chi-square test was used for data with a qualitative value and that of Kolmogorov-Sminorf for data with a quantitative value. Descriptive analysis was possible using R software version 3.2, SPSS version 25.0, XLSTAT 2016, PAST and EXCEL programs from Microsoft Office 2013. Results: The main results highlight economic stress, with 45.60% of households surveyed earning less than US$154 per month;55% of household heads were women in single-parent families;14% of household heads were unemployed, 22% worked in the private sector and 19% were self-employed. This general economic situation leads to precarious living conditions, thereby increasing the risk of high blood pressure among the Cameroonian population.
文摘Context/objectives: The fight against Chronic Non-Communicable Diseases (NCDs) is a long-term undertaking, which requires available, motivated and well-managed human resources (HR). The administrative management of skills on both qualitative and quantitative levels is one of the essential functions of a health system. To better implement policies of fight against High Blood Pressure (HBP) and other chronic diseases, it is important to establish strategies to retain health personnel. This loyalty requires favorable working conditions and consideration of the contribution-reward couple. Good working conditions are likely to reduce the phenomenon of medical nomadism;conversely, poor HR management can contribute to their exodus towards exotic “green pastures”, thus leading to an additional crisis in the Cameroonian health system. The fight against HBP is a complex, multifaceted and multifactorial reality that requires appropriate management model for all types of resources mainly HR. The main objective of this research is to show the impact of poor management of human resources in Cameroon health system on medical nomadism and the ineffectiveness of the fight against High Blood Pressure. Method: A cross-sectional descriptive survey among five hundred (500) health facilities in the center region of Cameroon has been conducted. A stratified probabilistic technique has been used, and the number of health facilities to be surveyed has been determined using the “sample size estimation table” of Depelteau. The physical questionnaires have been printed and then distributed to data collectors. After data collection, the latter were grouped during processing in Excel sheets. The Chi-square test was used for data with a qualitative value and that of Kolmogorov-Sminorf for data with a quantitative value to assess the normality and reliability of data. The Crochach’s Alpha reliability test allowed us to have a summary of the means and variances and then to search for intragroup correlations between variables. Descriptive analysis was possible with the XLSTAT 2016 software. Results: 43.60% of Health Facilities (HF) managers were unqualified. 82.20% of HF managers have staff in a situation of professional insecurity. They are mainly contractual (49.00), decision-making agents (24.40%), casual agents (08.80). The proportion of unstable personnel is average of 22.00% and very unstable, 12.00%.
文摘Introduction: High blood pressure is defined as blood pressure greater than or equal to 140 mm Hg for systolic and or 90 mm Hg for diastolic. It constitutes a major public health problem, the leading chronic disease in the world. The objective was to determine the prevalence, treatment rate and control of hypertension. Methods: This was a cross-sectional and descriptive study which took place over a period of 6 months in a hospital environment and in the general population. Results: Of the 1000 participants, 637 had hypertension, giving a prevalence of 63.70% with a female predominance. Thirty-three percent (33%) were unaware of their high blood pressure. The age group 60 and more was the most represented (44%). A proportion of 33 and 23.20 were overweight and obese participants, respectively. Male subjects were more overweight than female, unlike obesity which was more common among female subjects. Sixty-two percent (62%) of hypertensives were treated, of whom 44% were non-compliant. The excessively high cost and consumption of medications as needed were the main factors in therapeutic non-compliance. Twenty-two percent (22%) of all hypertensive patients and 35% of treated hypertensive patients were controlled. Women were more treated but less observant and less controlled than men. Therapeutic coverage and combination therapy rates were lower in rural areas. Hypertensives who had a high level of education were better treated and controlled than those who had no level. Conclusion: High blood pressure remains a real public health problem in Mali. It is more common in people aged 60 and over and in females. One in three hypertensives were unaware of their hypertension. The majority received antihypertensive treatments, but only a minority of them had their hypertension controlled.
文摘The large water transfer channels has a total length of more than 1000 km,spanning across the Huaihe River,the Yangtze River,the Yellow River and the Haihe River basins.During the preliminary design stage,the groundwater level was predicted based on the initial water level plus the groundwater level increase by precipitation infiltration and recharge in 1956 and 1996.However,after the rainfall in 2021 and 2023 to infiltrate and recharge groundwater,it is necessary to re-forecast the groundwater level.The Hebei section was taken as an example.Combined with the actual measurement of the historical maximum water level of the monitoring section and the inspection along the line,the water seepage of the canal slope was found.It is necessary to investigate the drainage system of the high groundwater level canal sections,take necessary treatment measures to improve the ability of the drainage system to cope with the rapid rise of high groundwater caused by heavy rainfall,and strengthen drainage measures for the risk parts of project safety in the high groundwater level canal sections,which are essential to ensure the safe operation of the middle route of the large water transfer channels.
基金supported by National Natural Science Foundation of China(No.41576108 and No.41605006)Natural Science Foundation project of Shandong Province(No.ZR2016DB26).
文摘Based on the principle of transient perturbation analysis,in this paper,a method to objectively determine the weather pattern formed by sea fog is provided.On the basis of the classification results,the circulation situation,divergence and vertical velocity field,and the vertical profile of temperature and humidity are synthesized and analyzed.The basic characteristics of the circulation and physical field of sea fog under low pressure control(L type sea fog)are obtained,and the results are compared with the sea fog under the control of high pressure(H type sea fog):a)L type sea fogs potential height anomaly disturbance is mainly manifested in the low layer,and its average value is-65.66 gpm,gradually weakening upward;b)L type sea fogs inversion structure is weaker than H type sea fogs when it occurs,the fog layer is thicker and the high relative humidity level is high over the fog layer,while the H type sea fogs fog layer has a relatively obvious dry layer;c)L sea fog has three layers of structure at the vertical direction.The first layer 1000-950 hPa is convergence accompanied by weak rise and subsidence,the second layer 950-850 hPa is divergence accompanied by weak subsidence,and the third layer 850 to 500hPa is gradually strengthened.While there are two layer structures of the H type sea fog.1000 hPa is divergence accompanied by weak rising and sinking movement,950-500 hPa is a uniform subsidence movement.d)Probability density statistical analysis further quantified the vertical movement of L and H type sea fog and the distribution of relative humidity in each layer.These conclusions provide an important reference for forecasting the sea fog in the northwest of the Yellow Sea under the condition of low pressure circulation in summer.
文摘To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids （fresh water-based and brine-based） under high temperature and high pressure （HTHP） with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.
