In order to further improve the precision forming efficiency of a sand mold digital patternless casting and reduce the amount of sand mold cutting, a method for near-net forming of the sand mold with digital flexible ...In order to further improve the precision forming efficiency of a sand mold digital patternless casting and reduce the amount of sand mold cutting, a method for near-net forming of the sand mold with digital flexible extrusion technology was put forward. The theory, optimization algorithm and technology for sand mold nearnet forming were studied. Experimental results show that the sand mold forming efficiency can be increased by 34%, and the molding sand can be reduced by 44%. The method for near-net forming of a sand mold with digital flexible extrusion technology can effectively promote the application of digital patternless casting technology in the mass production of castings and thus greatly improves the efficiency and automation of sand mold manufacturing.展开更多
Heat shocks caused by alloy melt and coat spraying are the main reason of die plastic deformation and early fracture. Based on theoretical analysis of heat shock phenomenon, two characteristic parameters of die damage...Heat shocks caused by alloy melt and coat spraying are the main reason of die plastic deformation and early fracture. Based on theoretical analysis of heat shock phenomenon, two characteristic parameters of die damage caused by heat shock were proposed, which are heat shock plastic deformation index (HSPI) and heat shock crack index (HSCI). The effect of heat shock on die plastic deformation and fracture behaviors was described quantitatively by these two parameters. HSPI represents approaching of heat shock stress to die yield stress. Plastic deformation will happen on a die if this index reaches 1. HSCI represents approaching of heat shock stress to die tensile strength. Die fracture will happen if this index reaches 1. According to theoretical analysis of heat transfer, theoretical models of HSPI and HSCI were established. It is found that, the smaller the interfacial thermal resistance (ITR) is, the higher the pouring temperature and die temperature are before heat shock, and the greater the HSPI and HSCI are, which can be fitted as exponential curves, linear and cubic curves.展开更多
Four different types of film-forming agents were added to the foundation formulations,and their effects on the makeup-holding properties of the foundations on human facial skin were determined by Visia-CR.The study sh...Four different types of film-forming agents were added to the foundation formulations,and their effects on the makeup-holding properties of the foundations on human facial skin were determined by Visia-CR.The study showed that there was a significant difference between the sample group with film-forming agent and the blank control group,indicating that the addition of film-forming agent had an effect on the makeup-holding performance of the foundation;the makeup-holding effect of the foundation formulated with trimethylsiloxysilicate or(acrylates/dimethicone copolymer,cyclopentasiloxane)was better than that of the foundation formulated with polymethylsilsesquioxane or VP/hexadecene copolymer.This experiment is of guidance significance for the formulation design of long-lasting foundation.展开更多
The glass-forming ability(GFA)of metallic glasses is a key scientific challenge in their development and application,with compositional dependence playing a crucial role.Experimental studies have demonstrated that the...The glass-forming ability(GFA)of metallic glasses is a key scientific challenge in their development and application,with compositional dependence playing a crucial role.Experimental studies have demonstrated that the addition of specific minor elements can greatly enhance the GFA of parent alloys,yet the underlying mechanism remains unclear.In this study,we use the ZrCuAl system as a model to explore how the addition of minor Al influences the crystallization rate by modulating the properties of the crystal-liquid interface,thereby affecting the GFA.The results reveal that the minor addition of Al significantly reduces the crystal growth rate,a phenomenon not governed by particle density fluctuations at the interface.The impact of minor element additions extends beyond a modest increase in crystal-unfavorable motifs in the bulk supercooled liquid.More importantly,it leads to a significant enrichment of these motifs at the crystal-supercooled liquid interface,forming a dense topological network of crystal-unfavorable structures that effectively prevent the growth of the crystalline interface and enhance GFA.Our results provide valuable insights for the design and development of high-performance metallic glasses.展开更多
The influence of geometric configuration on the friction characteristics during incremental sheet forming of AA5052 was analyzed by integrating surface morphology and its characteristic parameters,along with plastic s...The influence of geometric configuration on the friction characteristics during incremental sheet forming of AA5052 was analyzed by integrating surface morphology and its characteristic parameters,along with plastic strain,contact pressure,and area.The interface promotes lubrication and support when wall angles were≤40°,a 0.5 mm-thin sheet was used,and a 10 mm-large tool radius was employed.This mainly results in micro-plowing and plastic extrusion flow,leading to lower friction coefficient.However,when wall angles exceed 40°,significant plastic strain roughening occurs,leading to inadequate lubrication on the newly formed surface.Increased sheet thickness and decreased tool radius elevate contact pressure.These actions trigger micro-cutting and adhesion,potentially leading to localized scuffing and dimple tears,and higher friction coefficient.The friction mechanisms remain unaffected by the part’s plane curve features.As the forming process progresses,abrasive wear intensifies,and surface morphology evolves unfavorably for lubrication and friction reduction.展开更多
This article examines the influence of annealing temperature on fracture toughness and forming limit curves of dissimilar aluminum/silver sheets.In the cold roll bonding process,after brushing and acid washing,the pre...This article examines the influence of annealing temperature on fracture toughness and forming limit curves of dissimilar aluminum/silver sheets.In the cold roll bonding process,after brushing and acid washing,the prepared surfaces are placed on top of each other and by rolling with reduction more than 50%,the bonding between layers is established.In this research,the roll bonding process was done at room temperature,without the use of lubricants and with a 70%thickness reduction.Then,the final thickness of the Ag/Al bilayer sheet reached 350μm by several stages of cold rolling.Before cold rolling,it should be noted that to decrease the hardness created due to plastic deformation,the roll-bonded samples were subjected to annealing heat treatment at 400℃for 90 min.Thus,the final samples were annealed at 200,300 and 400℃for 90 min and cooled in a furnace to examine the annealing temperature effects.The uniaxial tensile and microhardness tests measured mechanical properties.Also,to investigate the fracture mechanism,the fractography of the cross-section was examined by scanning electron microscope(SEM).To evaluate the formability of Ag/Al bilayer sheets,forming limit curves were obtained experimentally through the Nakazima test.The resistance of composites to failure due to cracking was also investigated by fracture toughness.The results showed that annealing increases the elongation and formability of the Ag/Al bilayer sheet while reduces the ultimate tensile strength and fracture toughness.However,the changing trend is not the same at different temperatures,and according to the results,the most significant effect is obtained at 300℃and aluminum layers.It was also determined that by increasing annealing temperature,the fracture mechanism from shear ductile with small and shallow dimples becomes ductile with deep cavities.展开更多
Compared with traditional plastic forming,ultrasonic vibration plastic forming has the advantages of reducing the forming force and improving the surface quality of the workpiece.This technology has a very broad appli...Compared with traditional plastic forming,ultrasonic vibration plastic forming has the advantages of reducing the forming force and improving the surface quality of the workpiece.This technology has a very broad application prospect in industrial manufactur-ing.Researchers have conducted extensive research on the ultrasonic vibration plastic forming of metals and laid a deep foundation for the development of this field.In this review,metals were classified according to their crystal structures.The effects of ultrasonic vibration on the microstructure of face-centered cubic,body-centered cubic,and hexagonal close-packed metals during plastic forming and the mech-anism underlying ultrasonic vibration forming were reviewed.The main challenges and future research direction of the ultrasonic vibra-tion plastic forming of metals were also discussed.展开更多
In this research,we present the pure open multi-processing(OpenMP),pure message passing interface(MPI),and hybrid MPI/OpenMP parallel solvers within the dynamic explicit central difference algorithm for the coining pr...In this research,we present the pure open multi-processing(OpenMP),pure message passing interface(MPI),and hybrid MPI/OpenMP parallel solvers within the dynamic explicit central difference algorithm for the coining process to address the challenge of capturing fine relief features of approximately 50 microns.Achieving such precision demands the utilization of at least 7 million tetrahedron elements,surpassing the capabilities of traditional serial programs previously developed.To mitigate data races when calculating internal forces,intermediate arrays are introduced within the OpenMP directive.This helps ensure proper synchronization and avoid conflicts during parallel execution.Additionally,in the MPI implementation,the coins are partitioned into the desired number of regions.This division allows for efficient distribution of computational tasks across multiple processes.Numerical simulation examples are conducted to compare the three solvers with serial programs,evaluating correctness,acceleration ratio,and parallel efficiency.The results reveal a relative error of approximately 0.3%in forming force among the parallel and serial solvers,while the predicted insufficient material zones align with experimental observations.Additionally,speedup ratio and parallel efficiency are assessed for the coining process simulation.The pureMPI parallel solver achieves a maximum acceleration of 9.5 on a single computer(utilizing 12 cores)and the hybrid solver exhibits a speedup ratio of 136 in a cluster(using 6 compute nodes and 12 cores per compute node),showing the strong scalability of the hybrid MPI/OpenMP programming model.This approach effectively meets the simulation requirements for commemorative coins with intricate relief patterns.展开更多
In three-dimensional free-bending forming(3D-FBF),the tube is not overly constrained,and the plastic deformation behavior and forming quality of the bent tube are significantly affected by the critical structure of th...In three-dimensional free-bending forming(3D-FBF),the tube is not overly constrained,and the plastic deformation behavior and forming quality of the bent tube are significantly affected by the critical structure of the forming die lining.However,the effects of die-lining structural parameters on the tube quality,and a method to determine the combination of die-lining structural parameters is yet to be devised.This study aims to propose a new framework that allows one to understand the effects of various die-lining structural parameters on tube quality and to propose the best combination of die-lining structural parameters.First,finite-element modeling is performed to simulate 3D-FBF and examine the effects of individual die-lining structures on the quality of tube formation.The simulation results show that the deformation-zone length and die gap are positively correlated with the tube-section distortion and wall-thickness variation,whereas it shows an opposite trend with respect to the bending radius.Additionally,the lining chamfer radius of the bending die and the guide lining chamfer radius minimally affect the tube forming quality.Subsequently,the optimal die-lining structure is obtained using the response-surface method.The tube cross-sectional distortion rate reduced from 2.73 to 2.53%after the die lining is optimized.Additionally,the average inner-wall thickness reduced to 1.06 mm,whereas the average outer-wall thickness increased to 0.97 mm.This paper proposes a method for optimizing the forming-die-lining mechanism and for improving the tube forming quality in 3D-FBF.展开更多
Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic for...Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic forming process.In the present study,the influence of the related parameters on the forming quality of a 6063 aluminum alloy sinusoidal corrugation tube has been assessed.In particular,the orthogonal experimental design(OED)and central composite design(CCD)methods have been used.Through the range analysis and variance analysis of the experimental data,the influence degree of wire diameter(WD)and discharge energy(DE)on the forming quality was determined.Multiple regression analysis was performed using the response surface methodology.A prediction model for the attaching-die state coefficient was established accordingly.The following optimal arrangement of parameters was obtained(WD=0.759 mm,DE=2.926 kJ).The attaching-die state coefficient reached the peak value of 0.001.Better optimized wire diameter and discharge energy for a better attaching-die state could be screened by CCD compared with OED.The response surface method in CCD was more suitable for the design and optimization of the considered process parameters.展开更多
It is one concern of the researchers how magnesium(Mg)alloys solidify under different conditions and how their microstructure evolves during solidification,and what are the relationship between the macroscopic propert...It is one concern of the researchers how magnesium(Mg)alloys solidify under different conditions and how their microstructure evolves during solidification,and what are the relationship between the macroscopic properties and various microstructures.Such issues are difficult to be revealed through experiments only,especially for the newly developed Mg alloys,for which there is a lack of more systematic and mature system.However,multi-scale modeling and simulation can promote and deepen our understanding of the microstructure and its deformation mechanism.In this paper,we review and summarize the recent research progress of numerical simulation of Mg alloys in forming and microstructure,namely casting,extrusion,rolling,and welding,using crystal plasticity finite element(CPFEM)and molecular dynamics(DM)methods.Besides,the methods and innovations of modeling are also summarized.Lastly,the paper discusses the development prospects and challenges of the numerical simulation in the field of Mg alloys.展开更多
To further investigate the forming mechanism and springback characteristics of strips under multi-square punch forming (MSPF) considering partial-unloading effects, a series of concave form ing tests of strips are con...To further investigate the forming mechanism and springback characteristics of strips under multi-square punch forming (MSPF) considering partial-unloading effects, a series of concave form ing tests of strips are conducted on the MSPF machine. This paper aims to reveal the physical mecha nism of the elastic-plastic deformation in the MSPF process considering the effect of the forming ap proaches, and derive appropriate mathematical interpretations. The theoretical model is firstly estab lished to analyse the concave forming mechanism and springback characteristics of the strip, and its accuracy is then validated by experimental data. The forming history and load evolutions are depicted to explore the required forming capacity through the proposed analytical method. Besides, the paramet ric studies are carried out to discuss their effects on the springback of the strip. The results suggest that the deformation paths of the strip are influenced by the forming approach, and the springback of the strip in convex forming is larger than that in concave forming.展开更多
The DP1500 steel series successfully produced by Baosteel is a marked improvement over the cold-rolled hot-dip galvanized dual-phase steel series.Sufficient parameter data related to forming characteristics are needed...The DP1500 steel series successfully produced by Baosteel is a marked improvement over the cold-rolled hot-dip galvanized dual-phase steel series.Sufficient parameter data related to forming characteristics are needed for the successful application of dual-phase steel series in engineering structures.Therefore,differences in the mech-anical properties,forming limit,hole expansion ratio,and stretch bend limit of the 1.5 GPa ultrahigh-strength steel,including DP1500,QP1500,and MS1500,have been systematically studied.Results show that the DP1500 exhibits good plastic deformation performance and approximately 5% uniform elongation,and its true major strain minimum on the forming limit curve(FLC_(0)) value is approximately 0.083,which is higher and lower than the FLC_(0) values of MS1500 and QP1500 of the same strength grade,respectively.DP1500 also exhibits good flanging and pore expansion capabilities and superior performance to QP1500 and MS1500.The minimum radius-to-thickness(R/T) ratio(1.4) of DP1500 in the 90° bend tests transverse to the rolling direction is between the R/T ratios of MS1500 and the QP1500.Overall,the formability performance of DP1500 is between that of MS1500 and QP1500.Its excellent crash energy absorption and formability performance render it a suitable structural component,and it has been successfully tested and verified on a typical complex ultrahigh-strength steel skeleton structure.展开更多
Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natura...Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natural rock.Extrusion free forming(EFF)is a 3D printing technique that uses clay as the printing material and cures the specimens through high-temperature sintering.In this study,we attempted to use the EFF technology to fabricate artificial rock specimens.The results show the physico-mechanical properties of the specimens are significantly affected by the sintering temperature,while the nozzle diameter and layer thickness also have a certain impact.The specimens are primarily composed of SiO_(2),with mineral compositions similar to that of natural rocks.The density,uniaxial compressive strength(UCS),elastic modulus,and tensile strength of the printed specimens fall in the range of 1.65–2.54 g/cm3,16.46–50.49 MPa,2.17–13.35 GPa,and 0.82–17.18 MPa,respectively.It is capable of simulating different types of rocks,especially mudstone,sandstone,limestone,and gneiss.However,the simulation of hard rocks with UCS exceeding 50 MPa still requires validation.展开更多
Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate...Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.展开更多
We investigated the parametric optimization on incremental sheet forming of stainless steel using Grey Relational Analysis(GRA) coupled with Principal Component Analysis(PCA). AISI 316L stainless steel sheets were use...We investigated the parametric optimization on incremental sheet forming of stainless steel using Grey Relational Analysis(GRA) coupled with Principal Component Analysis(PCA). AISI 316L stainless steel sheets were used to develop double wall angle pyramid with aid of tungsten carbide tool. GRA coupled with PCA was used to plan the experiment conditions. Control factors such as Tool Diameter(TD), Step Depth(SD), Bottom Wall Angle(BWA), Feed Rate(FR) and Spindle Speed(SS) on Top Wall Angle(TWA) and Top Wall Angle Surface Roughness(TWASR) have been studied. Wall angle increases with increasing tool diameter due to large contact area between tool and workpiece. As the step depth, feed rate and spindle speed increase,TWASR decreases with increasing tool diameter. As the step depth increasing, the hydrostatic stress is raised causing severe cracks in the deformed surface. Hence it was concluded that the proposed hybrid method was suitable for optimizing the factors and response.展开更多
Hot flow forming(HFF)is a promising forming technology to manufacture thin-walled cylindrical part with longitudinal inner ribs(CPLIRs)made of magnesium(Mg)alloys,which has wide applications in the aerospace field.How...Hot flow forming(HFF)is a promising forming technology to manufacture thin-walled cylindrical part with longitudinal inner ribs(CPLIRs)made of magnesium(Mg)alloys,which has wide applications in the aerospace field.However,due to the thermo-mechanical coupling effect and the existence of stiffened structure,complex microstructure evolution and uneven microstructure occur easily at the cylindrical wall(CW)and inner rib(IR)of Mg alloy thin-walled CPLIRs during the HFF.In this paper,a modified cellular automaton(CA)model of Mg alloy considering the effects of deformation conditions on material parameters was developed using the artificial neural network(ANN)method.It is found that the ANN-modified CA model exhibits better predictability for the microstructure of hot deformation than the conventional CA model.Furthermore,the microstructure evolution of ZK61 alloy CPLIRs during the HFF was analyzed by coupling the modified CA model and finite element analysis(FEA).The results show that compared with the microstructure at the same layer of the IR,more refined grains and less sufficient DRX resulted from larger strain and strain rate occur at that of the CW;various differences of strain and strain rate in the wall-thickness exist between the CW and IR,which leads to the inhomogeneity of microstructure rising firstly and declining from the inside layer to outside layer;the obtained Hall-Petch relationship between the measured microhardness and predicted grain sizes at the CW and the IR indicates the reliability of the coupled FEA-CA simulation results.展开更多
Based on the advantages of triple-wire gas indirect arc welding(TW-GIA),such as small heat input,low dilution rate,and high deposition rate,the surfacing test on Q345 steel was carried out,and the surfacing forming ch...Based on the advantages of triple-wire gas indirect arc welding(TW-GIA),such as small heat input,low dilution rate,and high deposition rate,the surfacing test on Q345 steel was carried out,and the surfacing forming characteristics of TW-GIA were studied.Results showed that due to excessive wetting angle of the weld and the limitation of the heat source mode,there was unfused defect between the weld toes of the adjacent welds.To improve the morphology of the surfacing layer,the inclined substrate surfacing process was used.As the inclination angle increases,the size of unfused defect between adjacent welds gradually decreases.When the angle of inclination is in-creased to 30°-40°,the single-layer multi-pass surfacing layer with uniform forming and available fusion between welds can be achieved.Compared with tandem double-wire arc(T-DW)surfacing,the deposition rate of TW-GIA increased by 61.49%,while the dilution rate of the base metal decreased by 71.91%.The surfacing method has the advantages of a high deposition rate and low heat input,which is benefi-cial to improve the microstructure of the surfacing layer,making the coarse columnar crystals smaller,and improving the microhardness.The average microhardness level is 233.1 HV,which is higher than the average microhardness of the T-DW surfacing layer 220.4 HV.展开更多
In this study,the test subjects included the aluminum alloys 2A14 and 5A06,as well as the welding wires ER2319 and ER5356,single laser welding,laser welding with filler wire,laser metal inert gas(laser-MIG)hybrid weld...In this study,the test subjects included the aluminum alloys 2A14 and 5A06,as well as the welding wires ER2319 and ER5356,single laser welding,laser welding with filler wire,laser metal inert gas(laser-MIG)hybrid welding and laser-MIG hybrid welding with filler wire were carried out respectively to research the influence of aluminum alloy base material and welding wire on weld forming charac-teristics.The results show that:under the same test conditions,the penetration of the base material 5A06 is greater than that of 2A14,the maximum is about 51.3%,and the penetration filling ER5356 is greater than that of ER2319,the maximum is about 32.2%;for 2A14 alu-minum alloy,the penetration is basically unchanged after filling with ER5356,and there is a relatively large decrease after filling ER2319,the maximum is about 21.2%;for 5A06 aluminum alloy,the penetration decreases after filling both kinds of welding wire,the penetration achieved with filler wire ER2319 is lower than that of ER5356.At the same time,through the process of laser absorption in different metal materials,it was found that the differences in material composition led to different laser absorption rates,resulting in different energy utiliza-tion,which is an important reason for the correlation between aluminum alloy materials and laser-MIG hybrid welding with filler wire.展开更多
We estimate the electromagnetic form factor of the transverse part of cross section σTand provide a correction for the electromagnetic form factor of the longitudinal component of cross section σLfor the charged pio...We estimate the electromagnetic form factor of the transverse part of cross section σTand provide a correction for the electromagnetic form factor of the longitudinal component of cross section σLfor the charged pion within the frame work of hadronic operator. To achieve this, we consider a slightly deformed curve deviating from a straight line and construct a set of differential equations by comparing them to the equation determining charged pion wave function in a straight line case. By solving these equations, we employ the Fourier transform of these wave functions.展开更多
基金financially supported by the National Science Foundation for Distinguished Young Scholars of China(Grant No.51525503)
文摘In order to further improve the precision forming efficiency of a sand mold digital patternless casting and reduce the amount of sand mold cutting, a method for near-net forming of the sand mold with digital flexible extrusion technology was put forward. The theory, optimization algorithm and technology for sand mold nearnet forming were studied. Experimental results show that the sand mold forming efficiency can be increased by 34%, and the molding sand can be reduced by 44%. The method for near-net forming of a sand mold with digital flexible extrusion technology can effectively promote the application of digital patternless casting technology in the mass production of castings and thus greatly improves the efficiency and automation of sand mold manufacturing.
基金Project(2009ZX04014-072) supported by National S & T Major Project of ChinaProject(Z09000400950901) supported by Beijing Municipal Science and Technology Development Program
文摘Heat shocks caused by alloy melt and coat spraying are the main reason of die plastic deformation and early fracture. Based on theoretical analysis of heat shock phenomenon, two characteristic parameters of die damage caused by heat shock were proposed, which are heat shock plastic deformation index (HSPI) and heat shock crack index (HSCI). The effect of heat shock on die plastic deformation and fracture behaviors was described quantitatively by these two parameters. HSPI represents approaching of heat shock stress to die yield stress. Plastic deformation will happen on a die if this index reaches 1. HSCI represents approaching of heat shock stress to die tensile strength. Die fracture will happen if this index reaches 1. According to theoretical analysis of heat transfer, theoretical models of HSPI and HSCI were established. It is found that, the smaller the interfacial thermal resistance (ITR) is, the higher the pouring temperature and die temperature are before heat shock, and the greater the HSPI and HSCI are, which can be fitted as exponential curves, linear and cubic curves.
文摘Four different types of film-forming agents were added to the foundation formulations,and their effects on the makeup-holding properties of the foundations on human facial skin were determined by Visia-CR.The study showed that there was a significant difference between the sample group with film-forming agent and the blank control group,indicating that the addition of film-forming agent had an effect on the makeup-holding performance of the foundation;the makeup-holding effect of the foundation formulated with trimethylsiloxysilicate or(acrylates/dimethicone copolymer,cyclopentasiloxane)was better than that of the foundation formulated with polymethylsilsesquioxane or VP/hexadecene copolymer.This experiment is of guidance significance for the formulation design of long-lasting foundation.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.T2325004 and 52161160330)the support from the Hong Kong Institute of Advanced Studies through the materials cluster project。
文摘The glass-forming ability(GFA)of metallic glasses is a key scientific challenge in their development and application,with compositional dependence playing a crucial role.Experimental studies have demonstrated that the addition of specific minor elements can greatly enhance the GFA of parent alloys,yet the underlying mechanism remains unclear.In this study,we use the ZrCuAl system as a model to explore how the addition of minor Al influences the crystallization rate by modulating the properties of the crystal-liquid interface,thereby affecting the GFA.The results reveal that the minor addition of Al significantly reduces the crystal growth rate,a phenomenon not governed by particle density fluctuations at the interface.The impact of minor element additions extends beyond a modest increase in crystal-unfavorable motifs in the bulk supercooled liquid.More importantly,it leads to a significant enrichment of these motifs at the crystal-supercooled liquid interface,forming a dense topological network of crystal-unfavorable structures that effectively prevent the growth of the crystalline interface and enhance GFA.Our results provide valuable insights for the design and development of high-performance metallic glasses.
基金the support of the Key Research and Development Program of Shaanxi Province,China(No.2021GXLH-Z-049)。
文摘The influence of geometric configuration on the friction characteristics during incremental sheet forming of AA5052 was analyzed by integrating surface morphology and its characteristic parameters,along with plastic strain,contact pressure,and area.The interface promotes lubrication and support when wall angles were≤40°,a 0.5 mm-thin sheet was used,and a 10 mm-large tool radius was employed.This mainly results in micro-plowing and plastic extrusion flow,leading to lower friction coefficient.However,when wall angles exceed 40°,significant plastic strain roughening occurs,leading to inadequate lubrication on the newly formed surface.Increased sheet thickness and decreased tool radius elevate contact pressure.These actions trigger micro-cutting and adhesion,potentially leading to localized scuffing and dimple tears,and higher friction coefficient.The friction mechanisms remain unaffected by the part’s plane curve features.As the forming process progresses,abrasive wear intensifies,and surface morphology evolves unfavorably for lubrication and friction reduction.
基金Project(4013311)supported by the National Science Foundation of Iran(INSF)。
文摘This article examines the influence of annealing temperature on fracture toughness and forming limit curves of dissimilar aluminum/silver sheets.In the cold roll bonding process,after brushing and acid washing,the prepared surfaces are placed on top of each other and by rolling with reduction more than 50%,the bonding between layers is established.In this research,the roll bonding process was done at room temperature,without the use of lubricants and with a 70%thickness reduction.Then,the final thickness of the Ag/Al bilayer sheet reached 350μm by several stages of cold rolling.Before cold rolling,it should be noted that to decrease the hardness created due to plastic deformation,the roll-bonded samples were subjected to annealing heat treatment at 400℃for 90 min.Thus,the final samples were annealed at 200,300 and 400℃for 90 min and cooled in a furnace to examine the annealing temperature effects.The uniaxial tensile and microhardness tests measured mechanical properties.Also,to investigate the fracture mechanism,the fractography of the cross-section was examined by scanning electron microscope(SEM).To evaluate the formability of Ag/Al bilayer sheets,forming limit curves were obtained experimentally through the Nakazima test.The resistance of composites to failure due to cracking was also investigated by fracture toughness.The results showed that annealing increases the elongation and formability of the Ag/Al bilayer sheet while reduces the ultimate tensile strength and fracture toughness.However,the changing trend is not the same at different temperatures,and according to the results,the most significant effect is obtained at 300℃and aluminum layers.It was also determined that by increasing annealing temperature,the fracture mechanism from shear ductile with small and shallow dimples becomes ductile with deep cavities.
基金supported by the National Key R&D Program of China(No.2022YFE0121300)the Introduction Plan for High end Foreign Experts,China(No.G2023105001L)the Young Foreign Talent Program,China(No.QN2023105001L).
文摘Compared with traditional plastic forming,ultrasonic vibration plastic forming has the advantages of reducing the forming force and improving the surface quality of the workpiece.This technology has a very broad application prospect in industrial manufactur-ing.Researchers have conducted extensive research on the ultrasonic vibration plastic forming of metals and laid a deep foundation for the development of this field.In this review,metals were classified according to their crystal structures.The effects of ultrasonic vibration on the microstructure of face-centered cubic,body-centered cubic,and hexagonal close-packed metals during plastic forming and the mech-anism underlying ultrasonic vibration forming were reviewed.The main challenges and future research direction of the ultrasonic vibra-tion plastic forming of metals were also discussed.
基金supported by the fund from ShenyangMint Company Limited(No.20220056)Senior Talent Foundation of Jiangsu University(No.19JDG022)Taizhou City Double Innovation and Entrepreneurship Talent Program(No.Taizhou Human Resources Office[2022]No.22).
文摘In this research,we present the pure open multi-processing(OpenMP),pure message passing interface(MPI),and hybrid MPI/OpenMP parallel solvers within the dynamic explicit central difference algorithm for the coining process to address the challenge of capturing fine relief features of approximately 50 microns.Achieving such precision demands the utilization of at least 7 million tetrahedron elements,surpassing the capabilities of traditional serial programs previously developed.To mitigate data races when calculating internal forces,intermediate arrays are introduced within the OpenMP directive.This helps ensure proper synchronization and avoid conflicts during parallel execution.Additionally,in the MPI implementation,the coins are partitioned into the desired number of regions.This division allows for efficient distribution of computational tasks across multiple processes.Numerical simulation examples are conducted to compare the three solvers with serial programs,evaluating correctness,acceleration ratio,and parallel efficiency.The results reveal a relative error of approximately 0.3%in forming force among the parallel and serial solvers,while the predicted insufficient material zones align with experimental observations.Additionally,speedup ratio and parallel efficiency are assessed for the coining process simulation.The pureMPI parallel solver achieves a maximum acceleration of 9.5 on a single computer(utilizing 12 cores)and the hybrid solver exhibits a speedup ratio of 136 in a cluster(using 6 compute nodes and 12 cores per compute node),showing the strong scalability of the hybrid MPI/OpenMP programming model.This approach effectively meets the simulation requirements for commemorative coins with intricate relief patterns.
基金Supported by Open Fund of Jiangsu Industrial Perception and Intelligent Manufacturing Equipment Engineering Research Center of China(Grant No.ZK21-05-04)National Natural Science Foundation of China(Grant Nos.52105360,52175328)+1 种基金Fundamental Research Funds for the Central Universities of China(Grant No.NS2022061)Prince Sattam bin Abdulaziz University of Saudi Arabia(Grant No.PSAU/2024/R/1446).
文摘In three-dimensional free-bending forming(3D-FBF),the tube is not overly constrained,and the plastic deformation behavior and forming quality of the bent tube are significantly affected by the critical structure of the forming die lining.However,the effects of die-lining structural parameters on the tube quality,and a method to determine the combination of die-lining structural parameters is yet to be devised.This study aims to propose a new framework that allows one to understand the effects of various die-lining structural parameters on tube quality and to propose the best combination of die-lining structural parameters.First,finite-element modeling is performed to simulate 3D-FBF and examine the effects of individual die-lining structures on the quality of tube formation.The simulation results show that the deformation-zone length and die gap are positively correlated with the tube-section distortion and wall-thickness variation,whereas it shows an opposite trend with respect to the bending radius.Additionally,the lining chamfer radius of the bending die and the guide lining chamfer radius minimally affect the tube forming quality.Subsequently,the optimal die-lining structure is obtained using the response-surface method.The tube cross-sectional distortion rate reduced from 2.73 to 2.53%after the die lining is optimized.Additionally,the average inner-wall thickness reduced to 1.06 mm,whereas the average outer-wall thickness increased to 0.97 mm.This paper proposes a method for optimizing the forming-die-lining mechanism and for improving the tube forming quality in 3D-FBF.
基金supported by National Natural Science Foundation of China(Grant Nos.51975202(Junjia Cui received the grant)and 52175315(Guangyao Li received the grant)).
文摘Aluminum alloy thin-walled structures are widely used in the automotive industry due to their advantages related to light weight and crashworthiness.They can be produced at room temperature by the electrohydraulic forming process.In the present study,the influence of the related parameters on the forming quality of a 6063 aluminum alloy sinusoidal corrugation tube has been assessed.In particular,the orthogonal experimental design(OED)and central composite design(CCD)methods have been used.Through the range analysis and variance analysis of the experimental data,the influence degree of wire diameter(WD)and discharge energy(DE)on the forming quality was determined.Multiple regression analysis was performed using the response surface methodology.A prediction model for the attaching-die state coefficient was established accordingly.The following optimal arrangement of parameters was obtained(WD=0.759 mm,DE=2.926 kJ).The attaching-die state coefficient reached the peak value of 0.001.Better optimized wire diameter and discharge energy for a better attaching-die state could be screened by CCD compared with OED.The response surface method in CCD was more suitable for the design and optimization of the considered process parameters.
基金supported by the National Natural Science Foundation of China(No.52271091)Natural Science Foundation Project of Ningxia Province(No.2023AAC03324)the National Key Research and Development Program of China(No.2021YFB3701100).
文摘It is one concern of the researchers how magnesium(Mg)alloys solidify under different conditions and how their microstructure evolves during solidification,and what are the relationship between the macroscopic properties and various microstructures.Such issues are difficult to be revealed through experiments only,especially for the newly developed Mg alloys,for which there is a lack of more systematic and mature system.However,multi-scale modeling and simulation can promote and deepen our understanding of the microstructure and its deformation mechanism.In this paper,we review and summarize the recent research progress of numerical simulation of Mg alloys in forming and microstructure,namely casting,extrusion,rolling,and welding,using crystal plasticity finite element(CPFEM)and molecular dynamics(DM)methods.Besides,the methods and innovations of modeling are also summarized.Lastly,the paper discusses the development prospects and challenges of the numerical simulation in the field of Mg alloys.
文摘To further investigate the forming mechanism and springback characteristics of strips under multi-square punch forming (MSPF) considering partial-unloading effects, a series of concave form ing tests of strips are conducted on the MSPF machine. This paper aims to reveal the physical mecha nism of the elastic-plastic deformation in the MSPF process considering the effect of the forming ap proaches, and derive appropriate mathematical interpretations. The theoretical model is firstly estab lished to analyse the concave forming mechanism and springback characteristics of the strip, and its accuracy is then validated by experimental data. The forming history and load evolutions are depicted to explore the required forming capacity through the proposed analytical method. Besides, the paramet ric studies are carried out to discuss their effects on the springback of the strip. The results suggest that the deformation paths of the strip are influenced by the forming approach, and the springback of the strip in convex forming is larger than that in concave forming.
文摘The DP1500 steel series successfully produced by Baosteel is a marked improvement over the cold-rolled hot-dip galvanized dual-phase steel series.Sufficient parameter data related to forming characteristics are needed for the successful application of dual-phase steel series in engineering structures.Therefore,differences in the mech-anical properties,forming limit,hole expansion ratio,and stretch bend limit of the 1.5 GPa ultrahigh-strength steel,including DP1500,QP1500,and MS1500,have been systematically studied.Results show that the DP1500 exhibits good plastic deformation performance and approximately 5% uniform elongation,and its true major strain minimum on the forming limit curve(FLC_(0)) value is approximately 0.083,which is higher and lower than the FLC_(0) values of MS1500 and QP1500 of the same strength grade,respectively.DP1500 also exhibits good flanging and pore expansion capabilities and superior performance to QP1500 and MS1500.The minimum radius-to-thickness(R/T) ratio(1.4) of DP1500 in the 90° bend tests transverse to the rolling direction is between the R/T ratios of MS1500 and the QP1500.Overall,the formability performance of DP1500 is between that of MS1500 and QP1500.Its excellent crash energy absorption and formability performance render it a suitable structural component,and it has been successfully tested and verified on a typical complex ultrahigh-strength steel skeleton structure.
基金financially supported by the Beijing Natural Science Foundation for Young Scientists(Grant No.8214052)the Talent Fund of Beijing Jiaotong University(Grant No.2021RC226)the State Key Laboratory for GeoMechanics and Deep Underground Engineering,China University of Mining and Technology(Grant No.SKLGDUEK2115).
文摘Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natural rock.Extrusion free forming(EFF)is a 3D printing technique that uses clay as the printing material and cures the specimens through high-temperature sintering.In this study,we attempted to use the EFF technology to fabricate artificial rock specimens.The results show the physico-mechanical properties of the specimens are significantly affected by the sintering temperature,while the nozzle diameter and layer thickness also have a certain impact.The specimens are primarily composed of SiO_(2),with mineral compositions similar to that of natural rocks.The density,uniaxial compressive strength(UCS),elastic modulus,and tensile strength of the printed specimens fall in the range of 1.65–2.54 g/cm3,16.46–50.49 MPa,2.17–13.35 GPa,and 0.82–17.18 MPa,respectively.It is capable of simulating different types of rocks,especially mudstone,sandstone,limestone,and gneiss.However,the simulation of hard rocks with UCS exceeding 50 MPa still requires validation.
文摘Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.
文摘We investigated the parametric optimization on incremental sheet forming of stainless steel using Grey Relational Analysis(GRA) coupled with Principal Component Analysis(PCA). AISI 316L stainless steel sheets were used to develop double wall angle pyramid with aid of tungsten carbide tool. GRA coupled with PCA was used to plan the experiment conditions. Control factors such as Tool Diameter(TD), Step Depth(SD), Bottom Wall Angle(BWA), Feed Rate(FR) and Spindle Speed(SS) on Top Wall Angle(TWA) and Top Wall Angle Surface Roughness(TWASR) have been studied. Wall angle increases with increasing tool diameter due to large contact area between tool and workpiece. As the step depth, feed rate and spindle speed increase,TWASR decreases with increasing tool diameter. As the step depth increasing, the hydrostatic stress is raised causing severe cracks in the deformed surface. Hence it was concluded that the proposed hybrid method was suitable for optimizing the factors and response.
基金supported by the National Nat-ural Science Foundation of China(Grant Nos.51775194 and 52090043).
文摘Hot flow forming(HFF)is a promising forming technology to manufacture thin-walled cylindrical part with longitudinal inner ribs(CPLIRs)made of magnesium(Mg)alloys,which has wide applications in the aerospace field.However,due to the thermo-mechanical coupling effect and the existence of stiffened structure,complex microstructure evolution and uneven microstructure occur easily at the cylindrical wall(CW)and inner rib(IR)of Mg alloy thin-walled CPLIRs during the HFF.In this paper,a modified cellular automaton(CA)model of Mg alloy considering the effects of deformation conditions on material parameters was developed using the artificial neural network(ANN)method.It is found that the ANN-modified CA model exhibits better predictability for the microstructure of hot deformation than the conventional CA model.Furthermore,the microstructure evolution of ZK61 alloy CPLIRs during the HFF was analyzed by coupling the modified CA model and finite element analysis(FEA).The results show that compared with the microstructure at the same layer of the IR,more refined grains and less sufficient DRX resulted from larger strain and strain rate occur at that of the CW;various differences of strain and strain rate in the wall-thickness exist between the CW and IR,which leads to the inhomogeneity of microstructure rising firstly and declining from the inside layer to outside layer;the obtained Hall-Petch relationship between the measured microhardness and predicted grain sizes at the CW and the IR indicates the reliability of the coupled FEA-CA simulation results.
基金supported by the National Key Research and Development Program of China(Grant No.2022YFB4600900)the National Natural Science Foundation of China(Grant No.52175290).
文摘Based on the advantages of triple-wire gas indirect arc welding(TW-GIA),such as small heat input,low dilution rate,and high deposition rate,the surfacing test on Q345 steel was carried out,and the surfacing forming characteristics of TW-GIA were studied.Results showed that due to excessive wetting angle of the weld and the limitation of the heat source mode,there was unfused defect between the weld toes of the adjacent welds.To improve the morphology of the surfacing layer,the inclined substrate surfacing process was used.As the inclination angle increases,the size of unfused defect between adjacent welds gradually decreases.When the angle of inclination is in-creased to 30°-40°,the single-layer multi-pass surfacing layer with uniform forming and available fusion between welds can be achieved.Compared with tandem double-wire arc(T-DW)surfacing,the deposition rate of TW-GIA increased by 61.49%,while the dilution rate of the base metal decreased by 71.91%.The surfacing method has the advantages of a high deposition rate and low heat input,which is benefi-cial to improve the microstructure of the surfacing layer,making the coarse columnar crystals smaller,and improving the microhardness.The average microhardness level is 233.1 HV,which is higher than the average microhardness of the T-DW surfacing layer 220.4 HV.
基金supported by the Henan Science and Technology Plan Joint Fund Project(Key Project)(203ZP20230007).
文摘In this study,the test subjects included the aluminum alloys 2A14 and 5A06,as well as the welding wires ER2319 and ER5356,single laser welding,laser welding with filler wire,laser metal inert gas(laser-MIG)hybrid welding and laser-MIG hybrid welding with filler wire were carried out respectively to research the influence of aluminum alloy base material and welding wire on weld forming charac-teristics.The results show that:under the same test conditions,the penetration of the base material 5A06 is greater than that of 2A14,the maximum is about 51.3%,and the penetration filling ER5356 is greater than that of ER2319,the maximum is about 32.2%;for 2A14 alu-minum alloy,the penetration is basically unchanged after filling with ER5356,and there is a relatively large decrease after filling ER2319,the maximum is about 21.2%;for 5A06 aluminum alloy,the penetration decreases after filling both kinds of welding wire,the penetration achieved with filler wire ER2319 is lower than that of ER5356.At the same time,through the process of laser absorption in different metal materials,it was found that the differences in material composition led to different laser absorption rates,resulting in different energy utiliza-tion,which is an important reason for the correlation between aluminum alloy materials and laser-MIG hybrid welding with filler wire.
文摘We estimate the electromagnetic form factor of the transverse part of cross section σTand provide a correction for the electromagnetic form factor of the longitudinal component of cross section σLfor the charged pion within the frame work of hadronic operator. To achieve this, we consider a slightly deformed curve deviating from a straight line and construct a set of differential equations by comparing them to the equation determining charged pion wave function in a straight line case. By solving these equations, we employ the Fourier transform of these wave functions.
