The uniaxial compressive strength(UCS)of rocks is a vital geomechanical parameter widely used for rock mass classification,stability analysis,and engineering design in rock engineering.Various UCS testing methods and ...The uniaxial compressive strength(UCS)of rocks is a vital geomechanical parameter widely used for rock mass classification,stability analysis,and engineering design in rock engineering.Various UCS testing methods and apparatuses have been proposed over the past few decades.The objective of the present study is to summarize the status and development in theories,test apparatuses,data processing of the existing testing methods for UCS measurement.It starts with elaborating the theories of these test methods.Then the test apparatus and development trends for UCS measurement are summarized,followed by a discussion on rock specimens for test apparatus,and data processing methods.Next,the method selection for UCS measurement is recommended.It reveals that the rock failure mechanism in the UCS testing methods can be divided into compression-shear,compression-tension,composite failure mode,and no obvious failure mode.The trends of these apparatuses are towards automation,digitization,precision,and multi-modal test.Two size correction methods are commonly used.One is to develop empirical correlation between the measured indices and the specimen size.The other is to use a standard specimen to calculate the size correction factor.Three to five input parameters are commonly utilized in soft computation models to predict the UCS of rocks.The selection of the test methods for the UCS measurement can be carried out according to the testing scenario and the specimen size.The engineers can gain a comprehensive understanding of the UCS testing methods and its potential developments in various rock engineering endeavors.展开更多
Experimental studies on the compressive behavior of composite laminates after low velocity impact was carried out with two test methods.One is SACMA Standard,and the other is a small dimensional specimen test method.I...Experimental studies on the compressive behavior of composite laminates after low velocity impact was carried out with two test methods.One is SACMA Standard,and the other is a small dimensional specimen test method.Impact damage distributions,compressive failure process after impact,quasi static indentation and compression of laminates with a hole were brought into comparison between these two test methods.The results showed that there is a great difference between these two test methods.Compressive behavior of laminates after impact varies with different test methods.Residual compressive strength of laminates after low velocity impact measured with SACMA Standard can reflect stiffness properties of composite resins more wholely than that measured with the other method can do.Small dimensional specimen test method should be improved on as an experimental standard of compressive strength after impact.展开更多
The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economic...The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.展开更多
The measurement of pile axial load is of great significance to determining pile foundation design parameters such as skin friction and end bearing capacity and analyzing load transfer mechanisms.Affected by the temper...The measurement of pile axial load is of great significance to determining pile foundation design parameters such as skin friction and end bearing capacity and analyzing load transfer mechanisms.Affected by the temperature and ice content of frozen ground,the interface contact relationship between pile foundation and frozen soil is complicated,making pile axial load measurements more uncertain than that in non-frozen ground.Therefore,it is necessary to gain an in-depth understanding of the current pile axial load test methods.Four methods are systematically reviewed:vibrating wire sensors,strain gauges,sliding micrometers,and optical fiber strain sensors.At the same time,the applicability of the four test methods in frozen soil regions is discussed in detail.The first two methods are mature and commonly used.The sliding micrometer is only suitable for short-term measurement.While the Fiber Bragg grating(FBG)strain gauge meets the monitoring requirements,the Brillouin optical time-domain reflectometer(BOTDR)needs further verification.This paper aims to provide a technical reference for selecting and applying different methods in the pile axial load test for the stability study and bearing capacity assessment of pile foundations in cold regions.展开更多
Due to local uneven heating during the welding process,the residual stress of the structure after welding affects the reliability of it.In order to ensure the reliability,it is of great significance to test the residu...Due to local uneven heating during the welding process,the residual stress of the structure after welding affects the reliability of it.In order to ensure the reliability,it is of great significance to test the residual stress distribution of the welded joint.It has always been the focus to find a simple and feasible method for residual stress testing to quickly and accurately obtain the residual stress distribution of welded joints.The mechanical measurement method has high measurement accuracy,convenient and easy operation,but it will cause certain damage to the components.Physical measurement method can avoid damage to components,but its test cost is usually high,and its measurement accuracy can also be affected by the material microstructure characteristics of welded components.Based on the advantages and disadvantages of these two residual stress test methods,a modal test method is proposed.This method is a non-destructive measurement method.Based on the mathematical relationship between the residual stress of the welded structure and the natural frequency(mathematical model),the natural frequency is measured through the modal test to calculate the residual stress quickly.However,it is difficult to establish a mathematical model with this method,and it is not suitable for realization.展开更多
The factors influencing the permeability coefficient of gravelly soils used for the development of embankment dams(core wall)are analyzed.Such factors include(but are not limited to)soil size,anisotropy,density and bo...The factors influencing the permeability coefficient of gravelly soils used for the development of embankment dams(core wall)are analyzed.Such factors include(but are not limited to)soil size,anisotropy,density and boundary effects.A review of the literature is conducted and new directions of research are proposed.In such a framework,it is shown that gravelly soil with controlled density and vertical stress should be used to optimize the measurement of the vertical and horizontal permeability coefficients,respectively.展开更多
According to the physical and chemical characteristics of superfine powder extinguishing agent,three test methods are selected to measure the flow ability.By studying and comparing various test methods,apparatus and c...According to the physical and chemical characteristics of superfine powder extinguishing agent,three test methods are selected to measure the flow ability.By studying and comparing various test methods,apparatus and conditions,the optimum method and conditions to test flow property of superfine powder extinguishing agent are confirmed.展开更多
Using environmental random vibration as the excitation,traditional accelerometer method,non-contact video method and non-contact laser method were employed to determine the natural frequency of Kunyu River footbridge....Using environmental random vibration as the excitation,traditional accelerometer method,non-contact video method and non-contact laser method were employed to determine the natural frequency of Kunyu River footbridge.All the results of these three methods are close to 2.70 Hz,which are concordant with each other and hence credible.展开更多
[ Objectives] This study was conducted to establish a method for microbial limit test of Tongmai Tangyanming Capsule. [ Methods] According to the Chinese Pharmacopoei 2015 edition of the four general rules, the microb...[ Objectives] This study was conducted to establish a method for microbial limit test of Tongmai Tangyanming Capsule. [ Methods] According to the Chinese Pharmacopoei 2015 edition of the four general rules, the microbiological limits of non-sterile products were verified. [ Results] Tongmai Tangyanming Capsule has a strong inhibitory effect on Bacillus subtilis and Candida albicans. The antimicrobial activity was significantly eliminated after increasing the diluent （ 1 ： 20） ; and the recoveries were in the range of 0.5 -2 when the total quantities of aerobic microbes were determined by dilution method （1：20）. When the total quantities of mould and yeast were determined by dilution method （1：20）, the recoveries were from 0.5 to 2, and Escherichia coli, cholate-tolerant Gram-negative bacteria and Salmonella can be detected by the test solution dilution method. [ Condusions] With the plate method, the total quantities of aerobic bacteria and the quantities of mould and yeast were examined by increasing diluent, and conventional method was used for examination of control bacteria including E. coli, cholatetolerant Gram-negative bacteria and Salmonella. This method has been proved effective for microbial limit test of Tongmai Tangyanming Capsule, and can effectively control the quality of the preparation. The method is accurate and reliable.展开更多
[Objectives] This study was conducted to establish microbial limit test methods for traditional Chinese medicine preparations Yunpi Granules and Bupi Qiangli Paste. [Methods] According to General Rules of Part IV of C...[Objectives] This study was conducted to establish microbial limit test methods for traditional Chinese medicine preparations Yunpi Granules and Bupi Qiangli Paste. [Methods] According to General Rules of Part IV of Chinese Pharmacopoeia, applicability tests were conducted on microbial limit test methods for the above two traditional Chinese medicine preparations by the plate method. [Results] The established methods showed recovery values in the range of 0.5-2.0 for both experimental strains, and the control bacteria could be detected in the experimental group, but not in the negative control group. [Conclusions] The microbial limit test methods were reliable for the two traditional Chinese medicine preparations and could be used for quality control.展开更多
[Objectives] This study was conducted to establish a method for microbial limit test of Compound Gangbangui Capsule. [Methods] According to the Chinese Pharmacopoei 2015 edition of the four general rules,the microbiol...[Objectives] This study was conducted to establish a method for microbial limit test of Compound Gangbangui Capsule. [Methods] According to the Chinese Pharmacopoei 2015 edition of the four general rules,the microbiological limits of non-sterile products were verified. [Results]Compound Gangbangui Capsule has a strong inhibitory effect on S. aureus,and the antimicrobial activity was significantly eliminated after increasing the diluent（ 1∶ 20）; and the recoveries were in the range of 0. 5-2. 0 when the total quantities of aerobic microbes were determined by dilution method（ 1∶ 20）. When the total quantities of mould and yeast were determined by conventional method（ 1∶ 20）,the recoveries were from 0. 5 to 2. 0,and Escherichia coli can be detected in experimental groups by the test solution dilution method. [Conclusions]With the plate method,the total quantities of aerobic bacteria and the quantities of mould and yeast were examined by increasing diluent and conventional method,respectively,and control bacteria,E. coli was examined by conventional method. This method has been proved effective for microbial limit test of Compound Gangbangui Capsule,and can effectively control the quality of the preparation. The method is accurate and reliable.展开更多
From the perspective of test methods, this paper revisits the communicative testing features reflected in the Revised Syllabus of the BEC Handbook (2002) by carrying out detailed analyses of the Sample Listening of BE...From the perspective of test methods, this paper revisits the communicative testing features reflected in the Revised Syllabus of the BEC Handbook (2002) by carrying out detailed analyses of the Sample Listening of BEC Vantage. A table of the Sample Listening is then constructed by using Bachman's framework of test methods (1999). From the table and a layout of its components, this paper explicates the five communicative testing features embodied in the Revised BEC: authenticity, contextualization, communicativeness, overall ability and holistic, qualitative scoring method.展开更多
Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method br...Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.展开更多
Clinically,fractures are the main cause of computer-aided design and computer-aided manufacturing(CAD/CAM)3 mol%-yttria-stabilized tetragonal zirconia polycrystal(Y-TZP)all-ceramic dental restorations failure because ...Clinically,fractures are the main cause of computer-aided design and computer-aided manufacturing(CAD/CAM)3 mol%-yttria-stabilized tetragonal zirconia polycrystal(Y-TZP)all-ceramic dental restorations failure because of repetitive occlusal loading.The goal of this work is to study the effect of test methods and specimen’s size on the flexural strength of five ceramic products.Both biaxial flexure test(BI)and uni-axial flexure tests(UNI),including three-point flexure test(3PF)and four-point flexure test(4PF),are used in this study.For all five products,the flexural strength is as follows:BI>3PF>4PF.Furthermore,specimens with smaller size(3PF-s)have higher values than the bigger ones(3PF).The difference between BI and UNI resulted from the edge flaws in ceramic specimens.The relationship between different UNI(including 3PF-s,3PF and 4PF)can be explained according to Weibull statistical fracture theory.BI is recommended to evaluate the flexural strength of CAD/CAM Y-TZP dental ceramics.展开更多
This paper is a review of the past research of mechanical testing methods for natural fibre honeycomb sandwich structure as well as failure modes analysis at a microscopic level by using Scanning Electron Microscope (...This paper is a review of the past research of mechanical testing methods for natural fibre honeycomb sandwich structure as well as failure modes analysis at a microscopic level by using Scanning Electron Microscope (SEM). As the world is garnering attention towards renewable resources for environmental purposes, studies of natural fibre have been increasing as well as the application of natural fibre throughout various industries such as aerospace, automobiles, and construction sectors. This paper is started with brief information regarding the honeycomb sandwich structure, introduction to natural fibre, its applications as well as the factors affecting the performances of the structure. Next, the mechanical testing methods are listed out as well as the expected outcomes obtained from the respective testing. The mechanical properties are also identified by conducting lab tests according to the ASTM standard for sandwich and core structures. The microstructure of the deformed samples is then examined under Scanning Electron Microscope (SEM) by using different magnifications to study the failure mechanisms of the samples. The images obtained from the SEM test are analyzed by using fractography which will show the failure modes of the samples. This article is based on past research conducted by professional on the related topic.展开更多
1 Development of UHVDC transmission capabilities The economical development of China is closely connected with safe and reliable power supply.Load centers e.g.in central and eastern China need huge amounts of electric...1 Development of UHVDC transmission capabilities The economical development of China is closely connected with safe and reliable power supply.Load centers e.g.in central and eastern China need huge amounts of electrical power.Available energy resources and consumption areas are often distributed inverse.As a consequence it is necessary to import electrical power to load center areas in an economic and efficient way.展开更多
The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evalua...The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.展开更多
Gemstones have fascinated mankind forever,and people traveled far to find them.The Silk Road is one of the most traditional trade routes in the middle ages that was used to bring the precious stones to the European ma...Gemstones have fascinated mankind forever,and people traveled far to find them.The Silk Road is one of the most traditional trade routes in the middle ages that was used to bring the precious stones to the European market.Later,emeralds from Colombia were shipped via the ocean to the Old World.展开更多
With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure...With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure(CUCP)test cannot simulate the plastic yielding and instantaneous unloading process of supporting structure to rock.Thus,a high stress loading-instantaneous unloading confining pressure(HSL-IUCP)test method was proposed and applied by considering bolt’s fracture under stress.The wall thickness of confining pressure plates and the material of bolts were changed to realize different confin-ing pressure loading stiffness(CPLS)and lateral maximum allowable deformation(LMAD).The superio-rity of HSL-ICPU method is verified compared with CUCP.The rock failure mechanism caused by sudden failure of supporting structure is obtained.The results show that when CPLS increases from 1.35 to 2.33 GN/m,rock’s peak strength and elastic modulus increase by 25.18%and 23.70%,respectively.The fracture characteristics change from tensile failure to tensile-shear mixed failure.When LMAD decreases from 0.40 to 0.16 mm,rock’s residual strength,peak strain,and residual strain decrease by 91.80%,16.94%,and 21.92%,respectively,and post-peak drop modulus increases by 140.47%.The test results obtained by this method are closer to rock’s real mechanical response characteristics compared with CUCP.展开更多
基金the National Natural Science Foundation of China(Grant Nos.52308403 and 52079068)the Yunlong Lake Laboratory of Deep Underground Science and Engineering(No.104023005)the China Postdoctoral Science Foundation(Grant No.2023M731998)for funding provided to this work.
文摘The uniaxial compressive strength(UCS)of rocks is a vital geomechanical parameter widely used for rock mass classification,stability analysis,and engineering design in rock engineering.Various UCS testing methods and apparatuses have been proposed over the past few decades.The objective of the present study is to summarize the status and development in theories,test apparatuses,data processing of the existing testing methods for UCS measurement.It starts with elaborating the theories of these test methods.Then the test apparatus and development trends for UCS measurement are summarized,followed by a discussion on rock specimens for test apparatus,and data processing methods.Next,the method selection for UCS measurement is recommended.It reveals that the rock failure mechanism in the UCS testing methods can be divided into compression-shear,compression-tension,composite failure mode,and no obvious failure mode.The trends of these apparatuses are towards automation,digitization,precision,and multi-modal test.Two size correction methods are commonly used.One is to develop empirical correlation between the measured indices and the specimen size.The other is to use a standard specimen to calculate the size correction factor.Three to five input parameters are commonly utilized in soft computation models to predict the UCS of rocks.The selection of the test methods for the UCS measurement can be carried out according to the testing scenario and the specimen size.The engineers can gain a comprehensive understanding of the UCS testing methods and its potential developments in various rock engineering endeavors.
文摘Experimental studies on the compressive behavior of composite laminates after low velocity impact was carried out with two test methods.One is SACMA Standard,and the other is a small dimensional specimen test method.Impact damage distributions,compressive failure process after impact,quasi static indentation and compression of laminates with a hole were brought into comparison between these two test methods.The results showed that there is a great difference between these two test methods.Compressive behavior of laminates after impact varies with different test methods.Residual compressive strength of laminates after low velocity impact measured with SACMA Standard can reflect stiffness properties of composite resins more wholely than that measured with the other method can do.Small dimensional specimen test method should be improved on as an experimental standard of compressive strength after impact.
基金CDC/NIOSH for their partial funding of this work
文摘The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.
基金This study was supported by the Strategic Priority Research Program of the Chinese Academy of Science(Grant No.XDA20020102)Science and Technology Project of State Grid Corporation of China(Contract No.SGQHDKYOSBJS201600077)+1 种基金National Natural Science Foundation of China(Grant No.41101065)the State Key Laboratory of Frozen Soil Engineering Foundation(Grant No.SKLFSE-ZT-34)。
文摘The measurement of pile axial load is of great significance to determining pile foundation design parameters such as skin friction and end bearing capacity and analyzing load transfer mechanisms.Affected by the temperature and ice content of frozen ground,the interface contact relationship between pile foundation and frozen soil is complicated,making pile axial load measurements more uncertain than that in non-frozen ground.Therefore,it is necessary to gain an in-depth understanding of the current pile axial load test methods.Four methods are systematically reviewed:vibrating wire sensors,strain gauges,sliding micrometers,and optical fiber strain sensors.At the same time,the applicability of the four test methods in frozen soil regions is discussed in detail.The first two methods are mature and commonly used.The sliding micrometer is only suitable for short-term measurement.While the Fiber Bragg grating(FBG)strain gauge meets the monitoring requirements,the Brillouin optical time-domain reflectometer(BOTDR)needs further verification.This paper aims to provide a technical reference for selecting and applying different methods in the pile axial load test for the stability study and bearing capacity assessment of pile foundations in cold regions.
基金Project was supported by the National Natural Science Foundation of China(Grant No.52165034)Science and Technology Programs of Inner Mongolia(Grant No.2020GG0301)+1 种基金Natural Science Foundation of Inner Mongolia Autonomous Region(Grant No.2019MS05061)Scientific Research Projects of Higher Education of Inner Mongolia Autonomous Region Institutions(Grant No.NJZY20066).
文摘Due to local uneven heating during the welding process,the residual stress of the structure after welding affects the reliability of it.In order to ensure the reliability,it is of great significance to test the residual stress distribution of the welded joint.It has always been the focus to find a simple and feasible method for residual stress testing to quickly and accurately obtain the residual stress distribution of welded joints.The mechanical measurement method has high measurement accuracy,convenient and easy operation,but it will cause certain damage to the components.Physical measurement method can avoid damage to components,but its test cost is usually high,and its measurement accuracy can also be affected by the material microstructure characteristics of welded components.Based on the advantages and disadvantages of these two residual stress test methods,a modal test method is proposed.This method is a non-destructive measurement method.Based on the mathematical relationship between the residual stress of the welded structure and the natural frequency(mathematical model),the natural frequency is measured through the modal test to calculate the residual stress quickly.However,it is difficult to establish a mathematical model with this method,and it is not suitable for realization.
基金The work is supported by National Key Research and Development Program of China(No.2017YFC0404803)Guizhou High-Level Innovative Talents Project[2018](No.5630)+2 种基金Guizhou Science and Support[2019](No.2869)State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin(No.SKL2020ZY09)Science and Technology Project of Huaneng Group Headquarters(HNKJ17-H18).
文摘The factors influencing the permeability coefficient of gravelly soils used for the development of embankment dams(core wall)are analyzed.Such factors include(but are not limited to)soil size,anisotropy,density and boundary effects.A review of the literature is conducted and new directions of research are proposed.In such a framework,it is shown that gravelly soil with controlled density and vertical stress should be used to optimize the measurement of the vertical and horizontal permeability coefficients,respectively.
文摘According to the physical and chemical characteristics of superfine powder extinguishing agent,three test methods are selected to measure the flow ability.By studying and comparing various test methods,apparatus and conditions,the optimum method and conditions to test flow property of superfine powder extinguishing agent are confirmed.
基金Ministry of Science and Technology of China for sponsoring the"Cooperation Research on the Dynamic Safety and Serviceability of Public Structures Servicing for Human"(No.2010DFB74280)between Beijing Institute of Technology and Ruhr-University Bochum
文摘Using environmental random vibration as the excitation,traditional accelerometer method,non-contact video method and non-contact laser method were employed to determine the natural frequency of Kunyu River footbridge.All the results of these three methods are close to 2.70 Hz,which are concordant with each other and hence credible.
基金Supported by Special Fund for Research and Development of Traditional Chinese Medicine Modern Science and Technology Industry of Guizhou Province(qkhzyz[2011]5012)
文摘[ Objectives] This study was conducted to establish a method for microbial limit test of Tongmai Tangyanming Capsule. [ Methods] According to the Chinese Pharmacopoei 2015 edition of the four general rules, the microbiological limits of non-sterile products were verified. [ Results] Tongmai Tangyanming Capsule has a strong inhibitory effect on Bacillus subtilis and Candida albicans. The antimicrobial activity was significantly eliminated after increasing the diluent （ 1 ： 20） ; and the recoveries were in the range of 0.5 -2 when the total quantities of aerobic microbes were determined by dilution method （1：20）. When the total quantities of mould and yeast were determined by dilution method （1：20）, the recoveries were from 0.5 to 2, and Escherichia coli, cholate-tolerant Gram-negative bacteria and Salmonella can be detected by the test solution dilution method. [ Condusions] With the plate method, the total quantities of aerobic bacteria and the quantities of mould and yeast were examined by increasing diluent, and conventional method was used for examination of control bacteria including E. coli, cholatetolerant Gram-negative bacteria and Salmonella. This method has been proved effective for microbial limit test of Tongmai Tangyanming Capsule, and can effectively control the quality of the preparation. The method is accurate and reliable.
基金Supported by Science and Technology Planning Project of Guiyang CityGuizhou Province (ZKHT [2019]-9-4-15)+2 种基金Green Seedling Research Startup Foundation of The Second Affiliated Hospital of Guizhou University of Traditional Chinese Medicine (GZEYK-Y[2022]29)Research and Development CenterThe Second Affiliated Hospital of Guizhou University of Traditional Chinese Medicine(3040-04020001406)。
文摘[Objectives] This study was conducted to establish microbial limit test methods for traditional Chinese medicine preparations Yunpi Granules and Bupi Qiangli Paste. [Methods] According to General Rules of Part IV of Chinese Pharmacopoeia, applicability tests were conducted on microbial limit test methods for the above two traditional Chinese medicine preparations by the plate method. [Results] The established methods showed recovery values in the range of 0.5-2.0 for both experimental strains, and the control bacteria could be detected in the experimental group, but not in the negative control group. [Conclusions] The microbial limit test methods were reliable for the two traditional Chinese medicine preparations and could be used for quality control.
基金Supported by Traditional Chinese Medicine and Ethnic Minority Medicine Technique Research Subject of Guizhou Administrative Bureau of TCM(QZYY2011-40)
文摘[Objectives] This study was conducted to establish a method for microbial limit test of Compound Gangbangui Capsule. [Methods] According to the Chinese Pharmacopoei 2015 edition of the four general rules,the microbiological limits of non-sterile products were verified. [Results]Compound Gangbangui Capsule has a strong inhibitory effect on S. aureus,and the antimicrobial activity was significantly eliminated after increasing the diluent（ 1∶ 20）; and the recoveries were in the range of 0. 5-2. 0 when the total quantities of aerobic microbes were determined by dilution method（ 1∶ 20）. When the total quantities of mould and yeast were determined by conventional method（ 1∶ 20）,the recoveries were from 0. 5 to 2. 0,and Escherichia coli can be detected in experimental groups by the test solution dilution method. [Conclusions]With the plate method,the total quantities of aerobic bacteria and the quantities of mould and yeast were examined by increasing diluent and conventional method,respectively,and control bacteria,E. coli was examined by conventional method. This method has been proved effective for microbial limit test of Compound Gangbangui Capsule,and can effectively control the quality of the preparation. The method is accurate and reliable.
文摘From the perspective of test methods, this paper revisits the communicative testing features reflected in the Revised Syllabus of the BEC Handbook (2002) by carrying out detailed analyses of the Sample Listening of BEC Vantage. A table of the Sample Listening is then constructed by using Bachman's framework of test methods (1999). From the table and a layout of its components, this paper explicates the five communicative testing features embodied in the Revised BEC: authenticity, contextualization, communicativeness, overall ability and holistic, qualitative scoring method.
文摘Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.
基金This work was supported by grants from Natural Science Foundation of China(81200814)National Key Technology R&D Program of China(no.2012BAI22B03).
文摘Clinically,fractures are the main cause of computer-aided design and computer-aided manufacturing(CAD/CAM)3 mol%-yttria-stabilized tetragonal zirconia polycrystal(Y-TZP)all-ceramic dental restorations failure because of repetitive occlusal loading.The goal of this work is to study the effect of test methods and specimen’s size on the flexural strength of five ceramic products.Both biaxial flexure test(BI)and uni-axial flexure tests(UNI),including three-point flexure test(3PF)and four-point flexure test(4PF),are used in this study.For all five products,the flexural strength is as follows:BI>3PF>4PF.Furthermore,specimens with smaller size(3PF-s)have higher values than the bigger ones(3PF).The difference between BI and UNI resulted from the edge flaws in ceramic specimens.The relationship between different UNI(including 3PF-s,3PF and 4PF)can be explained according to Weibull statistical fracture theory.BI is recommended to evaluate the flexural strength of CAD/CAM Y-TZP dental ceramics.
文摘This paper is a review of the past research of mechanical testing methods for natural fibre honeycomb sandwich structure as well as failure modes analysis at a microscopic level by using Scanning Electron Microscope (SEM). As the world is garnering attention towards renewable resources for environmental purposes, studies of natural fibre have been increasing as well as the application of natural fibre throughout various industries such as aerospace, automobiles, and construction sectors. This paper is started with brief information regarding the honeycomb sandwich structure, introduction to natural fibre, its applications as well as the factors affecting the performances of the structure. Next, the mechanical testing methods are listed out as well as the expected outcomes obtained from the respective testing. The mechanical properties are also identified by conducting lab tests according to the ASTM standard for sandwich and core structures. The microstructure of the deformed samples is then examined under Scanning Electron Microscope (SEM) by using different magnifications to study the failure mechanisms of the samples. The images obtained from the SEM test are analyzed by using fractography which will show the failure modes of the samples. This article is based on past research conducted by professional on the related topic.
文摘1 Development of UHVDC transmission capabilities The economical development of China is closely connected with safe and reliable power supply.Load centers e.g.in central and eastern China need huge amounts of electrical power.Available energy resources and consumption areas are often distributed inverse.As a consequence it is necessary to import electrical power to load center areas in an economic and efficient way.
基金supported by the National Key Research and Development Program of China(Grant No.2023YFC2907600)the National Natural Science Foundation of China(Grant Nos.42277174 and 52204260).
文摘The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.
文摘Gemstones have fascinated mankind forever,and people traveled far to find them.The Silk Road is one of the most traditional trade routes in the middle ages that was used to bring the precious stones to the European market.Later,emeralds from Colombia were shipped via the ocean to the Old World.
基金the National Natural Science Foundation of China(Nos.52374218,52174122 and 52374094)Outstanding Youth Fund of Shandong Natural Science Foundation(No.ZR2022YQ49)Taishan Scholar Project in Shandong Province(Nos.tspd20210313 and tsqn202211150).
文摘With the increase of underground engineering construction depth,the phenomenon of surrounding rock sudden failure caused by supporting structure failure occurs frequently.The conventional unloading con-fining pressure(CUCP)test cannot simulate the plastic yielding and instantaneous unloading process of supporting structure to rock.Thus,a high stress loading-instantaneous unloading confining pressure(HSL-IUCP)test method was proposed and applied by considering bolt’s fracture under stress.The wall thickness of confining pressure plates and the material of bolts were changed to realize different confin-ing pressure loading stiffness(CPLS)and lateral maximum allowable deformation(LMAD).The superio-rity of HSL-ICPU method is verified compared with CUCP.The rock failure mechanism caused by sudden failure of supporting structure is obtained.The results show that when CPLS increases from 1.35 to 2.33 GN/m,rock’s peak strength and elastic modulus increase by 25.18%and 23.70%,respectively.The fracture characteristics change from tensile failure to tensile-shear mixed failure.When LMAD decreases from 0.40 to 0.16 mm,rock’s residual strength,peak strain,and residual strain decrease by 91.80%,16.94%,and 21.92%,respectively,and post-peak drop modulus increases by 140.47%.The test results obtained by this method are closer to rock’s real mechanical response characteristics compared with CUCP.
