Tensile behaviors of an AZS0 alloy were investigated by elongation-to-failure tensile tests at 300, 350, 400 and 450 ℃, and strain rates of 10-2 and 10-3 s 1. Strain-rate-change tests from 5×10-5 s-1 to 2x10-2 s...Tensile behaviors of an AZS0 alloy were investigated by elongation-to-failure tensile tests at 300, 350, 400 and 450 ℃, and strain rates of 10-2 and 10-3 s 1. Strain-rate-change tests from 5×10-5 s-1 to 2x10-2 s-1 were applied to study deformation mechanisms. The experimental data show that the material exhibits enhanced tensile ductilities of over 100% at 400 and 450 ℃ with stress exponent of 4.29 and activation energy of 149.60 kJ/mol, and initial fine grains preserve in evenly deformed gauge based on microstructure studies. The enhanced tensile ductilities are rate controlled by a competitive mechanism of grain boundary sliding and dislocation climb creep, based on which a model can successfully simulate the deformation behavior.展开更多
Tensile stress-strain curves of five metallic alloys,i.e.,SKH51,STS316L,Ti-6Al-4V,Al6061and Inconel600were analyzed to investigate the working hardening behavior.The constitutive parameters of three constitutive equat...Tensile stress-strain curves of five metallic alloys,i.e.,SKH51,STS316L,Ti-6Al-4V,Al6061and Inconel600were analyzed to investigate the working hardening behavior.The constitutive parameters of three constitutive equations,i.e.,the Hollomon,Swift and Voce equations,were compared by using different methods.A new working hardening parameter was proposed to characterize the working hardening behavior in different deformation stages.It is found that Voce equation is suitable to describe stress-strain curves in large strain region.Meanwhile,the predicting accuracy of ultimate tensile strength by Voce equation is the best.The working hardening behavior of SKH51is different from the other four metallic alloys.展开更多
This research provides experimental evidence for localized shear, billet cracking, and segmentation during the processing of various copper alloys. The results demonstrate that although many parameters affect the shea...This research provides experimental evidence for localized shear, billet cracking, and segmentation during the processing of various copper alloys. The results demonstrate that although many parameters affect the shear localization, there is a direct relation between segmentation and alloy strength （hardness） that is related to the alloying elements and constitutive phases. For instance, alpha brass is successfully processed by ECAP at room temperature, but alpha/beta brasses fail even at a temperature of 350 °C. Finite element simulation of cracking and segmentation was performed using DEFORMTM to investigate the influence of different parameters on segmentation. The results confirm that friction and processing speed have narrow effects on attaining a perfect billet. However, employing back pressure could be reliably used to diminish shear localization, billet cracking, segmentation, and damage. Moreover, diminishing the flow localization using back pressure leads to uniform material flow and the billet homogeneity increases by 36.1%, when back pressure increases from 0 to 600 MPa.展开更多
基金Project(50801034)supported by the National Natural Science Foundation of ChinaProject(LJQ 2011026)supported by Development Foundation for Excellent Young Scholars in Universities of Liaoning Province,ChinaProject(2006207)supported by Foundation for "Ten-Hundred-Thousand" High-end Talent Introduction Project in Liaoning Province,China
文摘Tensile behaviors of an AZS0 alloy were investigated by elongation-to-failure tensile tests at 300, 350, 400 and 450 ℃, and strain rates of 10-2 and 10-3 s 1. Strain-rate-change tests from 5×10-5 s-1 to 2x10-2 s-1 were applied to study deformation mechanisms. The experimental data show that the material exhibits enhanced tensile ductilities of over 100% at 400 and 450 ℃ with stress exponent of 4.29 and activation energy of 149.60 kJ/mol, and initial fine grains preserve in evenly deformed gauge based on microstructure studies. The enhanced tensile ductilities are rate controlled by a competitive mechanism of grain boundary sliding and dislocation climb creep, based on which a model can successfully simulate the deformation behavior.
基金Project(51275414)supported by the National Natural Science Foundation of ChinaProject(3102015BJ(Ⅱ)ZS007)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(130-QP-2015)supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU),China
文摘Tensile stress-strain curves of five metallic alloys,i.e.,SKH51,STS316L,Ti-6Al-4V,Al6061and Inconel600were analyzed to investigate the working hardening behavior.The constitutive parameters of three constitutive equations,i.e.,the Hollomon,Swift and Voce equations,were compared by using different methods.A new working hardening parameter was proposed to characterize the working hardening behavior in different deformation stages.It is found that Voce equation is suitable to describe stress-strain curves in large strain region.Meanwhile,the predicting accuracy of ultimate tensile strength by Voce equation is the best.The working hardening behavior of SKH51is different from the other four metallic alloys.
基金financial support and providing research facilities used in this work
文摘This research provides experimental evidence for localized shear, billet cracking, and segmentation during the processing of various copper alloys. The results demonstrate that although many parameters affect the shear localization, there is a direct relation between segmentation and alloy strength （hardness） that is related to the alloying elements and constitutive phases. For instance, alpha brass is successfully processed by ECAP at room temperature, but alpha/beta brasses fail even at a temperature of 350 °C. Finite element simulation of cracking and segmentation was performed using DEFORMTM to investigate the influence of different parameters on segmentation. The results confirm that friction and processing speed have narrow effects on attaining a perfect billet. However, employing back pressure could be reliably used to diminish shear localization, billet cracking, segmentation, and damage. Moreover, diminishing the flow localization using back pressure leads to uniform material flow and the billet homogeneity increases by 36.1%, when back pressure increases from 0 to 600 MPa.
