The properties of the self-compacting concrete mix depend on an automatic introduction of air bubbles caught during the process of mixing. What is interesting, the criterion for self-compactibility is not taken into c...The properties of the self-compacting concrete mix depend on an automatic introduction of air bubbles caught during the process of mixing. What is interesting, the criterion for self-compactibility is not taken into consideration in commonly used self-compacting tests. On the basis of different tests concerning self-compacting concrete mixes, it has been found out that too high air content in their volume was the result of superplasticizer, in spite of meeting the self-compactibility criteria （i.e., self-venting）. For the decrease of too high air volume in SCC, the use of anti-foaming admixture （AFA） is proposed. As a result, the effect of AFA mix flow diameter is increased and the flow time is decreased. Moreover, the workability loss is lower. In case of mix incorporating AFA, their high flowability does not cause segregation of the mix, what is possible in case of SCC incorporating only superplasticizer. However, the time of the introduction of AFA and its type is essential to get higher flowability degree, but it is not important to achieve low air volume in SCC.展开更多
This paper is devoted to investigate experimentally the strength evaluation of normal strength and self-compacting reinforced concrete beams under the effect of impact. The experimental work includes investigating of ...This paper is devoted to investigate experimentally the strength evaluation of normal strength and self-compacting reinforced concrete beams under the effect of impact. The experimental work includes investigating of eight （180×250×1,200 ram） beam specimens. Three variables are adopted in this paper： tensile reinforcement ratio, type of concrete （NSC （normal strength concrete） or SCC （self-compacting concrete）） and height of falling （dropped） ball （1 m or 2 m）. The experimental results indicated that the number of blows increased with increasing of tensile reinforcement ratio and compressive strength by about 35% and 123%, respectively. Maximum mid-span deflection was increased with increasing falling height and decreased with increasing reinforcement ration and concrete compressive strength. The increasing of concrete compressive strength is more effective than increasing of the reinforcement ratio, it appeared that the percentage of increasing exceeds 50%. The ultimate strength is decreased with increasing the falling height for about 34%-44%.展开更多
Concrete is a material which is in wide use in engineering especially in construction engineering and road infrastructure facilities. Development trends for high rise constructions, modern skyscrapers indicate that bu...Concrete is a material which is in wide use in engineering especially in construction engineering and road infrastructure facilities. Development trends for high rise constructions, modern skyscrapers indicate that building such constructions with normal concretes and low consistency is impossible, therefore there is a need for concrete with high processes because of great amount of reinforcement in cross-section of concrete elements. Solution for such construction is self-compacting concrete because of its ability to fill good formworks without compaction and vibration. Considering this fact, researches for cracks, mechanical characteristics of concrete and deformations have been conducted worldwide. In this paper, we conducted an experimental research to determine the cracks on beams of self-compacting concrete and compared it with conventional concrete. The experimentally-obtained results will be presented for both types of concrete for： module of elasticity, compression strength, crack with and cracks spacing for duration failure testing time t = 400 days.展开更多
This paper focuses on the results of experimental work on workability and compressive strength of self-compacting concrete （SCC）. The work concentrated on concrete mixes having water/binder ratios of 0.45 and 0.35, ...This paper focuses on the results of experimental work on workability and compressive strength of self-compacting concrete （SCC）. The work concentrated on concrete mixes having water/binder ratios of 0.45 and 0.35, which contained constant total binder contents of 400 kg/m^3 and 500 kg/m^3, respectively. Based on the experimental results, the existing suggestions for anticipating the long-term compressive strength of SCC according to its compressive strength at the age of 7 days were not exact enough. Therefore, it is decided to use artificial neural networks （ANN） for predicting the long-term compressive strength of SCC from its workability and short-term compressive strength. For predicting the long-term compressive strength of SCC utilizing ANN, multi layer perceptron （MLP） networks and radial basis function （RBF） networks were chosen. The conclusion was that the MLP networks could properly predict the long-term compressive strength in all conditions, but RBF networks were not exact enough in some circumstances. On the other hand, RBF networks were more users friendly and they converged to the final networks quicker.展开更多
In the structures whose long-term behavior should be monitored and controlled, creep and shrinkage effects have to be included precisely in the analysis and design procedures. Creep and shrinkage, vary with the consti...In the structures whose long-term behavior should be monitored and controlled, creep and shrinkage effects have to be included precisely in the analysis and design procedures. Creep and shrinkage, vary with the constituent and mixtures proportions, and depend on the curing conditions and work environment as well. Self-compacting concrete （SCC） contains combinations of various components, such as aggregate, cement, superplasticizer, water-reducing agent and other ingredients which affect the properties of the SCC including creep and shrinkage of the SCC. Hence, the realistic prediction creep and shrinkage strains of SCC are an important requirement of the design process of this type of concrete structures. In this study, three proposed creep models and four shrinkage models available in the literature are compared with the measured results of 52 mixtures for creep and 165 mixtures for shrinkage of SCC. The influence of various parameters, such as mixture design, cement content, filler content, aggregate content, and water cement ratio （w/c） on the creep and shrinkage of SCC are also compared and discussed.展开更多
Sand is an inert element essential in the composition of concrete; its use ensures granular continuity between the cement and gravel for better cohesion of concrete. This paper presents the results of a study that inv...Sand is an inert element essential in the composition of concrete; its use ensures granular continuity between the cement and gravel for better cohesion of concrete. This paper presents the results of a study that investigated the influence of sand quality on the properties of fresh and hardened SCC （self-compacting concrete）. The dune sands are very fine materials characterized by a high intergranular porosity, high surface area and low fineness modulus; on the other hand crushed （manufactured） sand has a high rate into thin and irregular shapes which influence the workability of concrete. The amount of dune sand varies from （0%, 50% to 100%） by weight of fine aggregates. The results show that the rheological properties favour the use of dune sands; however the mechanical properties support the use of crushed sand.展开更多
Self-compacting concrete （SCC） is defined so that no vibration is necessary for the compaction. The main criteria of producing SCC have to satisfy the following characteristics [1, 2, 3]： （1） Ability to flow into...Self-compacting concrete （SCC） is defined so that no vibration is necessary for the compaction. The main criteria of producing SCC have to satisfy the following characteristics [1, 2, 3]： （1） Ability to flow into and completely fill complex forms under its own weight; （2） Ability to pass through and bond to congested reinforcements; （3） High resistance to aggregate segregation. Self-compacting concrete presents a significant sign in improving the product quality and efficiency of the building industry. It also enhances the working conditions and the quality and appearance of concrete. Japan has been used self-compacting concrete in bridge, building and tunnel construction since the early 1990s. In the last decade, SCC has been produced a high potential for greater acceptance and wider applications in highway bridge construction in the Europe and U.S.. However, till now, there is no application of SCC in the construction industry in Egypt. Therefore, the main objective of this research is to produce SCC by using the locally available materials in our region such as basalt, gravel, sand, limestone powder and silica fume. Experimental programme was designed to characterize the properties of fresh and hardened SCC. It comprises different concrete mixes thbricated with different types and percentages of constituent materials. Three full-scale reinforced concrete beams were fabricated from the SCC mixes and tested under flexure. For the purpose of comparison, an extra RC beam was made of conventional normal concrete to serve as a reference beam. This study, in general, demonstrated that the applications of SCC in construction industry oiler products with enhanced characteristics as well as could be economical.展开更多
The design of unique chamber, in which the SCUWC （self-consolidating underwater concrete） can be tested under the impact of the hydrostatic pressure from 0.1 MPa to 0.5 MPa, is presented in the paper. The results of...The design of unique chamber, in which the SCUWC （self-consolidating underwater concrete） can be tested under the impact of the hydrostatic pressure from 0.1 MPa to 0.5 MPa, is presented in the paper. The results of the preliminary tests of the effect of the hydrostatic pressure on the compressive strength of SCUWC were shown. The impact of the hydrostatic pressure on the compressive strength values of test specimens has been confirmed. There has been an increase in the strength of the specimens taken from the upper parts of the concrete samples. As it can be seen from the preliminary research, the differences in compressive strength are related to the differences that occur in the size and distribution of air voids in the samples taken from upper and lower parts of the test specimens. On the basis of the carried out investigations of the compressive strength, it can be concluded that the hydrostatic pressure has a favorable effect on the compressive strength of the tested specimens of SCUWC. Increase of the compressive strength is observed mostly in the upper layers of the samples. Preliminary analysis of the quantity and distribution of air pores in the samples of concrete subjected to pressure 0.5 MPa confirms the positive impact of the hydrostatic pressure on the layers close to the surface indicated by the absence of large air voids above 1,500μm and by reducing the quantity of air pores of size above 300μm.展开更多
In this work, strength assessments and percentage of water absorption of self compacting concrete containing ground granulated blast furnace slag （GGBFS） and A1203 nanoparticles as binder have been investigated. Por...In this work, strength assessments and percentage of water absorption of self compacting concrete containing ground granulated blast furnace slag （GGBFS） and A1203 nanoparticles as binder have been investigated. Portland cement was replaced by different amounts of GGBFS and the properties of concrete specimens were investigated. Although it negatively impacts the physical and mechanical properties of concrete at early ages of curing, GGBFS was found to improve the physical and mechanical properties of concrete up to 45 wt% at later ages. A1203 nanoparticles with the average particle size of 15 nm were added partially to concrete with the optimum content of GGBFS and physical and mechanical properties of the specimens were measured. A1203 nanoparticle as a partial replacement of cement up to 3.0 wt% could accelerate C-S-H gel formation as a result of increased crystalline Ca（OH）2 amount at the early ages and hence increase strength and improve the resistance to water permeability of concrete specimens. The increase of the A1203 nanoparticles＇ content by more than 3.0 wt% would cause the reduction of the strength because of the decreased crystalline Ca（OH）2 content required for C-S-H gel formation. Several empirical relationships have been presented to predict flexural and split tensile strength of the specimens by means of the corresponding compressive strength at a certain age of curing. Accelerated peak appearance in conduction calorimetry tests, more weight loss in thermogravimetric analysis and more rapid appearance of the peaks related to hydrated products in X-ray diffraction results, all indicate that A1203 nanoparticles could improve mechanical and physical properties of the concrete specimens.展开更多
文摘The properties of the self-compacting concrete mix depend on an automatic introduction of air bubbles caught during the process of mixing. What is interesting, the criterion for self-compactibility is not taken into consideration in commonly used self-compacting tests. On the basis of different tests concerning self-compacting concrete mixes, it has been found out that too high air content in their volume was the result of superplasticizer, in spite of meeting the self-compactibility criteria （i.e., self-venting）. For the decrease of too high air volume in SCC, the use of anti-foaming admixture （AFA） is proposed. As a result, the effect of AFA mix flow diameter is increased and the flow time is decreased. Moreover, the workability loss is lower. In case of mix incorporating AFA, their high flowability does not cause segregation of the mix, what is possible in case of SCC incorporating only superplasticizer. However, the time of the introduction of AFA and its type is essential to get higher flowability degree, but it is not important to achieve low air volume in SCC.
文摘This paper is devoted to investigate experimentally the strength evaluation of normal strength and self-compacting reinforced concrete beams under the effect of impact. The experimental work includes investigating of eight （180×250×1,200 ram） beam specimens. Three variables are adopted in this paper： tensile reinforcement ratio, type of concrete （NSC （normal strength concrete） or SCC （self-compacting concrete）） and height of falling （dropped） ball （1 m or 2 m）. The experimental results indicated that the number of blows increased with increasing of tensile reinforcement ratio and compressive strength by about 35% and 123%, respectively. Maximum mid-span deflection was increased with increasing falling height and decreased with increasing reinforcement ration and concrete compressive strength. The increasing of concrete compressive strength is more effective than increasing of the reinforcement ratio, it appeared that the percentage of increasing exceeds 50%. The ultimate strength is decreased with increasing the falling height for about 34%-44%.
文摘Concrete is a material which is in wide use in engineering especially in construction engineering and road infrastructure facilities. Development trends for high rise constructions, modern skyscrapers indicate that building such constructions with normal concretes and low consistency is impossible, therefore there is a need for concrete with high processes because of great amount of reinforcement in cross-section of concrete elements. Solution for such construction is self-compacting concrete because of its ability to fill good formworks without compaction and vibration. Considering this fact, researches for cracks, mechanical characteristics of concrete and deformations have been conducted worldwide. In this paper, we conducted an experimental research to determine the cracks on beams of self-compacting concrete and compared it with conventional concrete. The experimentally-obtained results will be presented for both types of concrete for： module of elasticity, compression strength, crack with and cracks spacing for duration failure testing time t = 400 days.
文摘This paper focuses on the results of experimental work on workability and compressive strength of self-compacting concrete （SCC）. The work concentrated on concrete mixes having water/binder ratios of 0.45 and 0.35, which contained constant total binder contents of 400 kg/m^3 and 500 kg/m^3, respectively. Based on the experimental results, the existing suggestions for anticipating the long-term compressive strength of SCC according to its compressive strength at the age of 7 days were not exact enough. Therefore, it is decided to use artificial neural networks （ANN） for predicting the long-term compressive strength of SCC from its workability and short-term compressive strength. For predicting the long-term compressive strength of SCC utilizing ANN, multi layer perceptron （MLP） networks and radial basis function （RBF） networks were chosen. The conclusion was that the MLP networks could properly predict the long-term compressive strength in all conditions, but RBF networks were not exact enough in some circumstances. On the other hand, RBF networks were more users friendly and they converged to the final networks quicker.
文摘In the structures whose long-term behavior should be monitored and controlled, creep and shrinkage effects have to be included precisely in the analysis and design procedures. Creep and shrinkage, vary with the constituent and mixtures proportions, and depend on the curing conditions and work environment as well. Self-compacting concrete （SCC） contains combinations of various components, such as aggregate, cement, superplasticizer, water-reducing agent and other ingredients which affect the properties of the SCC including creep and shrinkage of the SCC. Hence, the realistic prediction creep and shrinkage strains of SCC are an important requirement of the design process of this type of concrete structures. In this study, three proposed creep models and four shrinkage models available in the literature are compared with the measured results of 52 mixtures for creep and 165 mixtures for shrinkage of SCC. The influence of various parameters, such as mixture design, cement content, filler content, aggregate content, and water cement ratio （w/c） on the creep and shrinkage of SCC are also compared and discussed.
文摘Sand is an inert element essential in the composition of concrete; its use ensures granular continuity between the cement and gravel for better cohesion of concrete. This paper presents the results of a study that investigated the influence of sand quality on the properties of fresh and hardened SCC （self-compacting concrete）. The dune sands are very fine materials characterized by a high intergranular porosity, high surface area and low fineness modulus; on the other hand crushed （manufactured） sand has a high rate into thin and irregular shapes which influence the workability of concrete. The amount of dune sand varies from （0%, 50% to 100%） by weight of fine aggregates. The results show that the rheological properties favour the use of dune sands; however the mechanical properties support the use of crushed sand.
文摘Self-compacting concrete （SCC） is defined so that no vibration is necessary for the compaction. The main criteria of producing SCC have to satisfy the following characteristics [1, 2, 3]： （1） Ability to flow into and completely fill complex forms under its own weight; （2） Ability to pass through and bond to congested reinforcements; （3） High resistance to aggregate segregation. Self-compacting concrete presents a significant sign in improving the product quality and efficiency of the building industry. It also enhances the working conditions and the quality and appearance of concrete. Japan has been used self-compacting concrete in bridge, building and tunnel construction since the early 1990s. In the last decade, SCC has been produced a high potential for greater acceptance and wider applications in highway bridge construction in the Europe and U.S.. However, till now, there is no application of SCC in the construction industry in Egypt. Therefore, the main objective of this research is to produce SCC by using the locally available materials in our region such as basalt, gravel, sand, limestone powder and silica fume. Experimental programme was designed to characterize the properties of fresh and hardened SCC. It comprises different concrete mixes thbricated with different types and percentages of constituent materials. Three full-scale reinforced concrete beams were fabricated from the SCC mixes and tested under flexure. For the purpose of comparison, an extra RC beam was made of conventional normal concrete to serve as a reference beam. This study, in general, demonstrated that the applications of SCC in construction industry oiler products with enhanced characteristics as well as could be economical.
文摘The design of unique chamber, in which the SCUWC （self-consolidating underwater concrete） can be tested under the impact of the hydrostatic pressure from 0.1 MPa to 0.5 MPa, is presented in the paper. The results of the preliminary tests of the effect of the hydrostatic pressure on the compressive strength of SCUWC were shown. The impact of the hydrostatic pressure on the compressive strength values of test specimens has been confirmed. There has been an increase in the strength of the specimens taken from the upper parts of the concrete samples. As it can be seen from the preliminary research, the differences in compressive strength are related to the differences that occur in the size and distribution of air voids in the samples taken from upper and lower parts of the test specimens. On the basis of the carried out investigations of the compressive strength, it can be concluded that the hydrostatic pressure has a favorable effect on the compressive strength of the tested specimens of SCUWC. Increase of the compressive strength is observed mostly in the upper layers of the samples. Preliminary analysis of the quantity and distribution of air pores in the samples of concrete subjected to pressure 0.5 MPa confirms the positive impact of the hydrostatic pressure on the layers close to the surface indicated by the absence of large air voids above 1,500μm and by reducing the quantity of air pores of size above 300μm.
文摘In this work, strength assessments and percentage of water absorption of self compacting concrete containing ground granulated blast furnace slag （GGBFS） and A1203 nanoparticles as binder have been investigated. Portland cement was replaced by different amounts of GGBFS and the properties of concrete specimens were investigated. Although it negatively impacts the physical and mechanical properties of concrete at early ages of curing, GGBFS was found to improve the physical and mechanical properties of concrete up to 45 wt% at later ages. A1203 nanoparticles with the average particle size of 15 nm were added partially to concrete with the optimum content of GGBFS and physical and mechanical properties of the specimens were measured. A1203 nanoparticle as a partial replacement of cement up to 3.0 wt% could accelerate C-S-H gel formation as a result of increased crystalline Ca（OH）2 amount at the early ages and hence increase strength and improve the resistance to water permeability of concrete specimens. The increase of the A1203 nanoparticles＇ content by more than 3.0 wt% would cause the reduction of the strength because of the decreased crystalline Ca（OH）2 content required for C-S-H gel formation. Several empirical relationships have been presented to predict flexural and split tensile strength of the specimens by means of the corresponding compressive strength at a certain age of curing. Accelerated peak appearance in conduction calorimetry tests, more weight loss in thermogravimetric analysis and more rapid appearance of the peaks related to hydrated products in X-ray diffraction results, all indicate that A1203 nanoparticles could improve mechanical and physical properties of the concrete specimens.
