In this paper, the design, construction and ocean testing of a wave energy conversion system are studied. Based on the motion characteristics of double buoys in ocean waves, a wave energy conversion system with perman...In this paper, the design, construction and ocean testing of a wave energy conversion system are studied. Based on the motion characteristics of double buoys in ocean waves, a wave energy conversion system with permanent magnet tubular linear generator （PMTLG） is proposed to convert ocean wave energy into electricity. The wave energy conversion system was installed in the Yellow Sea near Lianyungang, China. The ocean test re- suits indicate that it had dynamic and static performance, and obtained an expected amount of electricity. The calcu- lation result indicates the average output power was about 1 000 W, and the conversion efficiency from wave en- ergy into electricity was 1.4%. In addition, the wireless data communication, mechanics and oceanography were also discussed.展开更多
For the purpose of obtaining satisfactory performance of the non-circular gear & crank-rocker & gear trains (NCCRG) weft insertion mechanism which was proposed in this paper, the ideal kinematic curve of this ...For the purpose of obtaining satisfactory performance of the non-circular gear & crank-rocker & gear trains (NCCRG) weft insertion mechanism which was proposed in this paper, the ideal kinematic curve of this weft insertion mechanism was given, and the reverse solution models of this mechanism were established. A reverse design and simulation software was compiled based on Visual Basic 6.0 to obtain the mechanism parameters, including the pitch curves and tooth profiles of the non-circular gears. A test-bed of this mechanism was developed according to these parameters. The kinematic performance of this weft insertion mechanism was tested by high-speed video tape recorder with its corresponding video analytical software Blaster's MAS. And the test results were identical with the theoretical calculation. Compared with the conjugate cam weft insertion mechanism which is applied on TT96 rapier loom, under the condition of same weft insertion rate, the variation of acceleration of this mechanism is smaller. This novel weft insertion mechanism can meet the requirements of weft insertion on rapier looms with smooth and steady motion.展开更多
Based on 31 fabric property parameters tested by FAST test system and other test instruments, the principal factors of fabric style are obtained through the principal factor analysis method and computer program. Accor...Based on 31 fabric property parameters tested by FAST test system and other test instruments, the principal factors of fabric style are obtained through the principal factor analysis method and computer program. According to the correlation between each parameter and principal factor, the selected positive or negative coefficient, the objective evaluation model of fabric style has been established based on the percentage of variance. And wool fabrics have been taken for example to show how to use the objective evaluation model for fabric design.展开更多
AIM TO correlate Helicobacter pylori （H. pylorli）, EpsteinBarr virus （EBV） and human papillomavirus （HPV） with gastric cancer （GC） cases in Para State, Brazil.METHODS Tissue samples were obtained from 302 gast...AIM TO correlate Helicobacter pylori （H. pylorli）, EpsteinBarr virus （EBV） and human papillomavirus （HPV） with gastric cancer （GC） cases in Para State, Brazil.METHODS Tissue samples were obtained from 302 gastric adenocarcinomas. A rapid urease test was used to detect the presence of H. pylori, and the presence of the cagA gene in the HP-positive samples was confirmed by PCR. An RNA in situ hybridization test designed to complement Eberl RNA was used to detect the presence of EBV in the samples, and the L1 region of HPV was detected using nested PCR. Positive HPV samples were genotyped and analyzed for E6 and E7 viral gene expression. Infections were also correlated with the clinical and pathological characteristics of the patients.RESULTS The majority of the 302 samples analyzed were obtained from men （65%） aged 55 years or older （67%） and were classified as the intestinal subtype （55%）. All three pathogens were found in the samples analyzed in the present study （H. pylori： 87%, EBV： 20%, HPV： 3%）. Overall, 78% of the H. pylori-positive （H. pylorl＋） samples were cagA＋ （H. pylori-cagA＋）, and there was an association between the cytotoxic product of this gene and EBV. Coinfections of H. pylori-cagA＋ and EBV were correlated with the most advanced tumor stages. Although only 20% of the tumors were positive for EBV, infection with this virus was associated with distant metastasis. Only the HPV 16 and 18 strains were found in the samples, although no expression of the E6 and E7 oncoproteins was detected. The fundus of the stomach was the region least affected by the pathogens.CONCLUSION HPV was not involved in gastric tumorigenesis. Prophy- lactic and therapeutic measures against H. pylori and EBV may prevent the development of GC, especially the more aggressive forms.展开更多
A quantitative measure-based method for the design and evaluation of sustainable products is proposed. The method uses multi-criteria in product design to meet sustainable requirements from qualitative criteria to qua...A quantitative measure-based method for the design and evaluation of sustainable products is proposed. The method uses multi-criteria in product design to meet sustainable requirements from qualitative criteria to quantitative metrics. The method integrates quality function deployment concepts with the life cycle assessment to establish a quantitative method for sustainable product development. It considers both customer needs and sustainable requirements by mapping these needs into design details using the axiomatic design and benchmarking methods. The method is applied in the wheelchair design. Four popular wheelchairs in the market are selected as benchmarks and are rated based on customer needs and sustainable criteria. The design matrix identifies the relationship of functional requirements and design parameters of the wheelchair. Compared to the best benchmark product, the proposed wheelchair can reduce costs by 13.8%, environment footprints 18.55%, mass 4.5%, and components 2.2%.展开更多
To fabricate the comb target with low damping and high performance-price ratio,0.03-\{0.1 mm\} thickness aluminum foi l used as the conducting medium,the upper and lower surfaces covered with 0.5-1 mm thickness plasti...To fabricate the comb target with low damping and high performance-price ratio,0.03-\{0.1 mm\} thickness aluminum foi l used as the conducting medium,the upper and lower surfaces covered with 0.5-1 mm thickness plastic film,after four processes of thrusting,laminating,punching and cu tting,a 500 mm×\{500 mm\} comb target is fabricated.A 155-mm projectile expl osiv e pow er test is conducted.Using the newly fabricated comb target,the measured initi al velocity of the fragment is 2 070 m/s.Th e test results show that the new comb target is of high test pre cision,small damping,low cost and high production efficiency,and it can measure th e 2 mm×2 m m fragment's initial velocity.展开更多
Similarity measure construction has been proposed as fault detection of flight test method in order to obtain the primary control surface stuck and the combination stuck of primary control.Similarity measures were obt...Similarity measure construction has been proposed as fault detection of flight test method in order to obtain the primary control surface stuck and the combination stuck of primary control.Similarity measures were obtained through analyzing the certainty and uncertainty of fuzzy membership functions,which were designed based on well-known Hamming distance.It was applied to the fault detection of primary control surface stuck of uninhabited aerial vehicle(UAV).At post-failure control surface,if the UAV is controllable and trimmable using other control surfaces,the UAV is able to fly or return to the safety region through reconfiguration of flight control system.To detect the fault,similarity measure computations were carried out.This result could be applicable with the real-time parameter estimation method.By monitoring the value of coefficients due to the control surface deviation,it becomes aware that the control surface fault occurs or not.The control surface stuck position and value were separated by comparing the trim value with the reference value.This is the advantage of increasing in reliability without adding sensors or with additional low cost.展开更多
Many websites use verification codes to prevent users from using the machine automatically to register,login,malicious vote or irrigate but it brought great burden to the enterprises involved in internet marketing as ...Many websites use verification codes to prevent users from using the machine automatically to register,login,malicious vote or irrigate but it brought great burden to the enterprises involved in internet marketing as entering the verification code manually.Improving the verification code security system needs the identification method as the corresponding testing system.We propose an anisotropic heat kernel equation group which can generate a heat source scale space during the kernel evolution based on infinite heat source axiom,design a multi-step anisotropic verification code identification algorithm which includes core procedure of building anisotropic heat kernel,settingwave energy information parameters,combing outverification codccharacters and corresponding peripheral procedure of gray scaling,binarizing,denoising,normalizing,segmenting and identifying,give out the detail criterion and parameter set.Actual test show the anisotropic heat kernel identification algorithm can be used on many kinds of verification code including text characters,mathematical,Chinese,voice,3D,programming,video,advertising,it has a higher rate of 25%and 50%than neural network and context matching algorithm separately for Yahoo site,49%and 60%for Captcha site,20%and 52%for Baidu site,60%and 65%for 3DTakers site,40%,and 51%.for MDP site.展开更多
A new type of pit supporting structure, which was tested and verified using the sensor monitoring technology, was presented. The new supporting structure is assembled by prefabricated steel structural units. The adjac...A new type of pit supporting structure, which was tested and verified using the sensor monitoring technology, was presented. The new supporting structure is assembled by prefabricated steel structural units. The adjacent steel structural units are jointed with fasteners, and each steel structural unit has a certain radian and is welded by two steel tubes and one piece of steel disc. In order to test and verify the reliability of the new supporting structure, the field tests are designed. The main monitoring programs include the hoop stress of supporting structure, lateral earth pressure, and soil deformation. The monitoring data of the field tests show that the new supporting structure is convenient, reliable and safe.展开更多
The IEEE Standard 1149.1 boundary scan (BS) implementation provides the internal access required for testing the digital printed circuit board (PCB). However, the integrity of the boundary scan test infrastructure sh...The IEEE Standard 1149.1 boundary scan (BS) implementation provides the internal access required for testing the digital printed circuit board (PCB). However, the integrity of the boundary scan test infrastructure should be tested first to guarantee the validation of the results of the rest functional test and diagnosis. This paper describes the fault models and test principles of the BS test access port (TAP) lines on PCBs. A test algorithm with high fault coverage and short time is then presented for the PCB on which all ICs are BS ones.展开更多
Mango fruit （Mangifera indica） is very rich in fibre and vitamin C which are the required nutrients for good health and easy digestion of food in human body system. However, the fruit is highly perishable in its nat...Mango fruit （Mangifera indica） is very rich in fibre and vitamin C which are the required nutrients for good health and easy digestion of food in human body system. However, the fruit is highly perishable in its natural state after harvest due to the chemical deterioration and environmental effects. Due to the perishable nature, abundant wastage during the production season and relative scarcity during the off season were recorded by farmers. Processing the fruit into the form that can easily be stored, preserved, packaged, transported or consumed is crucial to having the product all the year round. Besides, mango juice can be consumed freshly, processed into dry powder, mixed or blended with other juice to make fruit jams, or evaporated to concentrates. These products have a lot of potential in food and beverage industries for export and foreign exchange earnings. Therefore, a small scale machine to process mango fruits to high quality juice is highly essential to reduce the postharvest loss and then add value to the commodity. To achieve this purpose, an abrasion-macerating device （AMD） was designed, fabricated and tested for small scale mango juice extraction. Design considerations focused on the techno-economic status of the micro and small scale fruit juice processors who are the intended users of the machine. The major components of the machine included hopper, perforated drum, screw conveyor, juice outlet, waste outlet, frame, electric motor and motor stand. Other components included screw shaft, the juice collector, top cover and the transmission system. In operation, the screw conveyor conveys and presses the mango fruits against the perforated roughened drum. The abrasion/tearing process of the screw on the flesh of the fruit and further pressing against the drum squeeze enough juice out of the fruit. The juice extracted is drained through the perforated mesh of the juice channel into the juice outlet from where it is collected while the residual waste is collected at the waste outlet. The machine was tested using freshly harvested mango fruits and results obtained showed an average juice yield, extraction efficiency and extraction loss of 34,56%, 55.14% and 10.15%, respectively. These values of juice yield, extraction efficiency and low level of extraction loss indicate satisfactory performance of the machine. Powered by a 2.5 hp single-phase electric motor, the machine has a production cost of USD565 with the construction materials being locally available at affordable costs. A cottage mango juice extraction plant based on this technology can provide employment for at least two persons at the same time providing fresh juice at low costs and residual waste as an ingredient for livestock feed manufacturing.展开更多
This paper presents modified version of a realistic test tool suitable to Design For Testability （DFT） and Built-ln Self Test （BIST） environments. A comprehensive tool is developed in the form of a test simulator....This paper presents modified version of a realistic test tool suitable to Design For Testability （DFT） and Built-ln Self Test （BIST） environments. A comprehensive tool is developed in the form of a test simulator. The simulator is capable of providing a required goal of test for the Circuit Under Test （CUT）. The simulator uses the approach of fault diagnostics with fault grading procedures to provide the optimum tests. The current version of the simulator embeds features of exhaustive and pseudo-random test generation schemes along with the search solutions of cost effective test goals. The simulator provides facilities of realizing all possible pseudo-random sequence generators with all possible combinations of seeds. The tool is developed on a common Personal Computer （PC） platform and hence no special software is required. Thereby, it is a low cost tool hence economical. The tool is very much suitable for determining realistic test sequences for a targeted goal of testing for any CUT. The developed tool incorporates flexible Graphical User Interface （GUI） procedures and can be operated without any special programming skill. The tool is debugged and tested with the results of many bench mark circuits. Further, this developed tool can be utilized for educational purposes for many courses such as fault-tolerant computing, fault diagnosis, digital electronics, and safe-reliable-testable digital logic designs.展开更多
Statistical power, number of replicates and experiment complexity of semi-field and field studies on Apis and non-Apis bee species has become a major issue after publication of the draft European Food Safety Authori...Statistical power, number of replicates and experiment complexity of semi-field and field studies on Apis and non-Apis bee species has become a major issue after publication of the draft European Food Safety Authority （EFSA） Guidance on risk assessment of plant protection products （PPP） on bees （Apis mellifera, Bombus spp. and solitary bees）. According to this guidance document, field studies have to be designed to be able to detect significance differences as low as 7% for certain endpoints such as reduction in colony size. This will require an immense number of replicates which is obviously not feasible. In the present study, key endpoints such as mortality, termination rate and number of brood cells in honeybee studies, cocoon production and flight activity in solitary bee studies and number of gynes in bumble bee studies （just to mention some of the endpoints considered） in semi-field studies were analyzed, with Apis mellifera, Bombus terrestris and Osmia bicornis during the past five years （2013-2017）. The results indicate huge differences in the percentage minimal detectable differences （%MDDs） （MDD expressed as median of control value of the endpoint in percent） depending on endpoint and species tested. For honeybee semi-field studies, the lowest %MDDs recorded were between 10% and 15% for the endpoints foraging, number of brood cells and colony strength. The highest %MDDs were observed for the endpoint termination rate, with a %MDD of almost 50%. For the endpoints in bumble bee semi-field studies the %MDDs varied between 17% for bumble bee colony weight and 53% for average mortality during the exposure period in the tunnel. The %MDD for the number of gynes （young queens） was slightly below 25%. For the semi-field solitary bee test system, the %MDDs for the measured endpoints seem to be lower than those for the other two species tested. The %MDDs for the endpoints hatching of offspring, nest occupation and number of cocoons were 8%, 13% and 14%, respectively. Most of the %MDDs were between 10% and 30% indicating clearly that the currently performed experimental design for the semi-field pollinator studies allowed to determine relatively small effects on key study endpoints. The analysis indicated that for all the three bee species tested, the semi-field test design detected low %MDDs for most of the endpoints. It was also observed that detectable differences between the control and PPP treatments were much lower in semi-field test designs than in field studies with these bee species. The “perfect sample size” really does not exist but test design and statistical analysis can be adapted to lower the %MDDs. Measured and simulated （according to Student’s t-test-distribution） data and results showed that statistical evaluations parameter selection （e.g., alpha value）, data transformation （log10） and the number of replicates had a direct effect on the ability of the test design to detect lower or higher %MDD values. It could show that a change of alpha value from 0.05 to 0.1, increases the ability of the studies to detect lower %MDDs. For most of the measured endpoints, increasing the number of replicates e.g., from four to eight, improved the power of the test design by decreasing the %MDD. The reduction magnitude of the %MDD is dependent on the endpoint and selection of statistical parameters such as the alpha value. Parameters that display effects at a biologically relevant scale will be a better indicator for effects than parameters that are able to detect minor differences that are not biologically relevant.展开更多
Parity testing is one of the compact testing techniques, which, traditionally, relies on applying all 2^n input combinations to an n-input combinational circuit without need of knowing the implementation of the circui...Parity testing is one of the compact testing techniques, which, traditionally, relies on applying all 2^n input combinations to an n-input combinational circuit without need of knowing the implementation of the circuits under test. The faults can be detected just by observing and comparing its parity of whole output of circuit with the expectation one. The way seemed to be less interesting to the test eagineers in the past days, mainly due to the reasons of its exhaustive testing and time-cousuming, which became a barrier as the number of input lines gets growing. However its great facility and convenience in testing still interest to the engineers who need to have a quick look at the qualities of the circuits without generating the test patterns for a given circuit to be tested. In this paper, a new approach called pseudo-parity testing is presented to deal with the dilemma we are facing： i. e. to change an exhaustive parity testing into a non-exhaustive one, followed by a pseudo- parity testable design to help realize the new way of pseudo-parity testing. The idea of pseudo-parity testing presented in this paper may resume its spirits towards its promising future.展开更多
In order to achieve an access to strain sensor data with wireless transmission in bridge engineering structure testing, a wireless strain test system is presented based on the resistance strain sensor of networks. The...In order to achieve an access to strain sensor data with wireless transmission in bridge engineering structure testing, a wireless strain test system is presented based on the resistance strain sensor of networks. The wireless bridge strain test system composed of master station and substation adopts the wireless method to realize the high accuracy data acquisition between the master station and the substation under a reliable communication protocol. The system has been tested in contrast with the present strain apparatus. Results show that the wireless system is high-reliable, and has many characteristics such as high efficiency, good precision, high stability with low cost, and good flexibility, without using the present communication network.展开更多
In order to design the relief system size of di-tert-butyl peroxide(DTBP) storage tanks,the runaway re-action of DTBP was simulated by accelerating rate calorimeter(ARC).The results indicated that under adiabatic cond...In order to design the relief system size of di-tert-butyl peroxide(DTBP) storage tanks,the runaway re-action of DTBP was simulated by accelerating rate calorimeter(ARC).The results indicated that under adiabatic conditions the initial exothermic temperature was 102.6 ℃,the maximum self-heating rate was 3.095×107 ℃·min-1,the maximum self-heating temperature was 375.9 ℃,and the pressure produced by unit mass was 4.512 MPa·g-1.Judged by ARC test,the emergency relief system for DTBP was a hybrid system.Based on Design Institute for Emergency Relief System(DIERS) method,the releasing mass flow rate W was determined by Leung methods,and the mass velocity G was calculated by two modified Omega methods.The two relief sizes calculated by monograph Omega method and arithmetic Omega method are close,with only 0.63% relative error.The monograph Omega method is more convenient to apply.展开更多
During advanced water detection using the transient electromagnetic method, the exploration effect for water-rich area is often poor due to the interference of bolts that are distributed in different positions in work...During advanced water detection using the transient electromagnetic method, the exploration effect for water-rich area is often poor due to the interference of bolts that are distributed in different positions in working face. Thus, the study on the interference characteristics of bolts in different states has important directive significance for improving the acquisition quality and data processing method in water detection. Based on the analysis of the distribution laws of magnetic field excited by small multi-turn coincident loop in full space of homogeneity, the test on the interference of bolts has been designed in the mine. Through drilling 18 holes around the overlapping coil in the working face, mass data are collected in order with the posi- tion change and the exposed bolt length. The results of comprehensive data analysis show that the transient electromagnetic field is strongly interfered as the distance between the bolt and the center of the coil is less than 3 m, and the interference varies greatly as the distance varies. On the other hand, the field induced by the bolts can be ignored as the distance exceeds 3 m. The findings can help to improve data acquisition and correction during advanced water detection when using the transient electromagnetic method.展开更多
For the conventional single-ended eFuse cell, sensing failures can occur due to a variation of a post-program eFuse resistance during the data retention time and a relatively high program resistance of several kilo oh...For the conventional single-ended eFuse cell, sensing failures can occur due to a variation of a post-program eFuse resistance during the data retention time and a relatively high program resistance of several kilo ohms. A differential paired eFuse cell is designed which is about half the size smaller in sensing resistance of a programmed eFuse link than the conventional single-ended eFuse cell. Also, a sensing circuit of sense amplifier is proposed, based on D flip-flop structure to implement a simple sensing circuit. Furthermore, a sensing margin test circuit is proposed with variable pull-up loads out of consideration for resistance variation of a programmed eFuse. When an 8 bit eFuse OTP IP is designed with 0.18 ~tm standard CMOS logic of TSMC, the layout dimensions are 229.04 μm ×100.15μm. All the chips function successfully when 20 test chips are tested with a program voltage of 4.2 V.展开更多
through the design of teaching aerobics web-based course and application practice, the instructional design process based on B/ S learning are analyzed, and discusses several key problems in the design and teaching. T...through the design of teaching aerobics web-based course and application practice, the instructional design process based on B/ S learning are analyzed, and discusses several key problems in the design and teaching. This paper presents the resource based learning aerobics teaching design network course should adapt to the application mode of network teaching and traditional classroom combination; that will provide teaching demonstration, teaching contents for students as well as the function of self testing evaluation and provide the job management, teacher online Q ＆ A, database and knowledge base construction, greatly improving the ＂aerobics＂ teaching efficiency.展开更多
基金Supported by the National Natural Science Foundation of China(No.41076054)Special Foundation for State Oceanic Administration of China(No.GHME2011GD02)Scientific Research Foundation of Graduate School of Southeast University(No.YBJJ1416)
文摘In this paper, the design, construction and ocean testing of a wave energy conversion system are studied. Based on the motion characteristics of double buoys in ocean waves, a wave energy conversion system with permanent magnet tubular linear generator （PMTLG） is proposed to convert ocean wave energy into electricity. The wave energy conversion system was installed in the Yellow Sea near Lianyungang, China. The ocean test re- suits indicate that it had dynamic and static performance, and obtained an expected amount of electricity. The calcu- lation result indicates the average output power was about 1 000 W, and the conversion efficiency from wave en- ergy into electricity was 1.4%. In addition, the wireless data communication, mechanics and oceanography were also discussed.
基金National Natural Science Foundation of China(No.50875243)
文摘For the purpose of obtaining satisfactory performance of the non-circular gear & crank-rocker & gear trains (NCCRG) weft insertion mechanism which was proposed in this paper, the ideal kinematic curve of this weft insertion mechanism was given, and the reverse solution models of this mechanism were established. A reverse design and simulation software was compiled based on Visual Basic 6.0 to obtain the mechanism parameters, including the pitch curves and tooth profiles of the non-circular gears. A test-bed of this mechanism was developed according to these parameters. The kinematic performance of this weft insertion mechanism was tested by high-speed video tape recorder with its corresponding video analytical software Blaster's MAS. And the test results were identical with the theoretical calculation. Compared with the conjugate cam weft insertion mechanism which is applied on TT96 rapier loom, under the condition of same weft insertion rate, the variation of acceleration of this mechanism is smaller. This novel weft insertion mechanism can meet the requirements of weft insertion on rapier looms with smooth and steady motion.
文摘Based on 31 fabric property parameters tested by FAST test system and other test instruments, the principal factors of fabric style are obtained through the principal factor analysis method and computer program. According to the correlation between each parameter and principal factor, the selected positive or negative coefficient, the objective evaluation model of fabric style has been established based on the percentage of variance. And wool fabrics have been taken for example to show how to use the objective evaluation model for fabric design.
基金the National Council for scientific and technological development,No.(CNPq)402283/2013-9
文摘AIM TO correlate Helicobacter pylori （H. pylorli）, EpsteinBarr virus （EBV） and human papillomavirus （HPV） with gastric cancer （GC） cases in Para State, Brazil.METHODS Tissue samples were obtained from 302 gastric adenocarcinomas. A rapid urease test was used to detect the presence of H. pylori, and the presence of the cagA gene in the HP-positive samples was confirmed by PCR. An RNA in situ hybridization test designed to complement Eberl RNA was used to detect the presence of EBV in the samples, and the L1 region of HPV was detected using nested PCR. Positive HPV samples were genotyped and analyzed for E6 and E7 viral gene expression. Infections were also correlated with the clinical and pathological characteristics of the patients.RESULTS The majority of the 302 samples analyzed were obtained from men （65%） aged 55 years or older （67%） and were classified as the intestinal subtype （55%）. All three pathogens were found in the samples analyzed in the present study （H. pylori： 87%, EBV： 20%, HPV： 3%）. Overall, 78% of the H. pylori-positive （H. pylorl＋） samples were cagA＋ （H. pylori-cagA＋）, and there was an association between the cytotoxic product of this gene and EBV. Coinfections of H. pylori-cagA＋ and EBV were correlated with the most advanced tumor stages. Although only 20% of the tumors were positive for EBV, infection with this virus was associated with distant metastasis. Only the HPV 16 and 18 strains were found in the samples, although no expression of the E6 and E7 oncoproteins was detected. The fundus of the stomach was the region least affected by the pathogens.CONCLUSION HPV was not involved in gastric tumorigenesis. Prophy- lactic and therapeutic measures against H. pylori and EBV may prevent the development of GC, especially the more aggressive forms.
基金The Natural Sciences and Engineering Research Council(NSERC)of Canada(No.RGPIN/239189-2010)the National Natural Science Foundation of China(No.51375287)
文摘A quantitative measure-based method for the design and evaluation of sustainable products is proposed. The method uses multi-criteria in product design to meet sustainable requirements from qualitative criteria to quantitative metrics. The method integrates quality function deployment concepts with the life cycle assessment to establish a quantitative method for sustainable product development. It considers both customer needs and sustainable requirements by mapping these needs into design details using the axiomatic design and benchmarking methods. The method is applied in the wheelchair design. Four popular wheelchairs in the market are selected as benchmarks and are rated based on customer needs and sustainable criteria. The design matrix identifies the relationship of functional requirements and design parameters of the wheelchair. Compared to the best benchmark product, the proposed wheelchair can reduce costs by 13.8%, environment footprints 18.55%, mass 4.5%, and components 2.2%.
文摘To fabricate the comb target with low damping and high performance-price ratio,0.03-\{0.1 mm\} thickness aluminum foi l used as the conducting medium,the upper and lower surfaces covered with 0.5-1 mm thickness plastic film,after four processes of thrusting,laminating,punching and cu tting,a 500 mm×\{500 mm\} comb target is fabricated.A 155-mm projectile expl osiv e pow er test is conducted.Using the newly fabricated comb target,the measured initi al velocity of the fragment is 2 070 m/s.Th e test results show that the new comb target is of high test pre cision,small damping,low cost and high production efficiency,and it can measure th e 2 mm×2 m m fragment's initial velocity.
基金Project(20110018394) supported by Key Research Institute Program through the National Research Foundation (NRF) of Korea
文摘Similarity measure construction has been proposed as fault detection of flight test method in order to obtain the primary control surface stuck and the combination stuck of primary control.Similarity measures were obtained through analyzing the certainty and uncertainty of fuzzy membership functions,which were designed based on well-known Hamming distance.It was applied to the fault detection of primary control surface stuck of uninhabited aerial vehicle(UAV).At post-failure control surface,if the UAV is controllable and trimmable using other control surfaces,the UAV is able to fly or return to the safety region through reconfiguration of flight control system.To detect the fault,similarity measure computations were carried out.This result could be applicable with the real-time parameter estimation method.By monitoring the value of coefficients due to the control surface deviation,it becomes aware that the control surface fault occurs or not.The control surface stuck position and value were separated by comparing the trim value with the reference value.This is the advantage of increasing in reliability without adding sensors or with additional low cost.
基金The national natural science foundation(61273290,61373147)Xiamen Scientific Plan Project(2014S0048,3502Z20123037)+1 种基金Fujian Scientific Plan Project(2013HZ0004-1)FuJian provincial education office A-class project(-JA13238)
文摘Many websites use verification codes to prevent users from using the machine automatically to register,login,malicious vote or irrigate but it brought great burden to the enterprises involved in internet marketing as entering the verification code manually.Improving the verification code security system needs the identification method as the corresponding testing system.We propose an anisotropic heat kernel equation group which can generate a heat source scale space during the kernel evolution based on infinite heat source axiom,design a multi-step anisotropic verification code identification algorithm which includes core procedure of building anisotropic heat kernel,settingwave energy information parameters,combing outverification codccharacters and corresponding peripheral procedure of gray scaling,binarizing,denoising,normalizing,segmenting and identifying,give out the detail criterion and parameter set.Actual test show the anisotropic heat kernel identification algorithm can be used on many kinds of verification code including text characters,mathematical,Chinese,voice,3D,programming,video,advertising,it has a higher rate of 25%and 50%than neural network and context matching algorithm separately for Yahoo site,49%and 60%for Captcha site,20%and 52%for Baidu site,60%and 65%for 3DTakers site,40%,and 51%.for MDP site.
基金Project(41202220) supported by the National Natural Science Foundation of ChinaProject(20120022120003) supported by the Research Fund for the Doctoral Program of Higher Education, China+1 种基金Project(2-9-2012-65) supported by the Fundamental Research Funds for the Central Universities, ChinaProject(2013006) supported by the Research Fund for Key Laboratory on Deep GeoDrilling Technology, Ministry of Land and Resources, China
文摘A new type of pit supporting structure, which was tested and verified using the sensor monitoring technology, was presented. The new supporting structure is assembled by prefabricated steel structural units. The adjacent steel structural units are jointed with fasteners, and each steel structural unit has a certain radian and is welded by two steel tubes and one piece of steel disc. In order to test and verify the reliability of the new supporting structure, the field tests are designed. The main monitoring programs include the hoop stress of supporting structure, lateral earth pressure, and soil deformation. The monitoring data of the field tests show that the new supporting structure is convenient, reliable and safe.
文摘The IEEE Standard 1149.1 boundary scan (BS) implementation provides the internal access required for testing the digital printed circuit board (PCB). However, the integrity of the boundary scan test infrastructure should be tested first to guarantee the validation of the results of the rest functional test and diagnosis. This paper describes the fault models and test principles of the BS test access port (TAP) lines on PCBs. A test algorithm with high fault coverage and short time is then presented for the PCB on which all ICs are BS ones.
文摘Mango fruit （Mangifera indica） is very rich in fibre and vitamin C which are the required nutrients for good health and easy digestion of food in human body system. However, the fruit is highly perishable in its natural state after harvest due to the chemical deterioration and environmental effects. Due to the perishable nature, abundant wastage during the production season and relative scarcity during the off season were recorded by farmers. Processing the fruit into the form that can easily be stored, preserved, packaged, transported or consumed is crucial to having the product all the year round. Besides, mango juice can be consumed freshly, processed into dry powder, mixed or blended with other juice to make fruit jams, or evaporated to concentrates. These products have a lot of potential in food and beverage industries for export and foreign exchange earnings. Therefore, a small scale machine to process mango fruits to high quality juice is highly essential to reduce the postharvest loss and then add value to the commodity. To achieve this purpose, an abrasion-macerating device （AMD） was designed, fabricated and tested for small scale mango juice extraction. Design considerations focused on the techno-economic status of the micro and small scale fruit juice processors who are the intended users of the machine. The major components of the machine included hopper, perforated drum, screw conveyor, juice outlet, waste outlet, frame, electric motor and motor stand. Other components included screw shaft, the juice collector, top cover and the transmission system. In operation, the screw conveyor conveys and presses the mango fruits against the perforated roughened drum. The abrasion/tearing process of the screw on the flesh of the fruit and further pressing against the drum squeeze enough juice out of the fruit. The juice extracted is drained through the perforated mesh of the juice channel into the juice outlet from where it is collected while the residual waste is collected at the waste outlet. The machine was tested using freshly harvested mango fruits and results obtained showed an average juice yield, extraction efficiency and extraction loss of 34,56%, 55.14% and 10.15%, respectively. These values of juice yield, extraction efficiency and low level of extraction loss indicate satisfactory performance of the machine. Powered by a 2.5 hp single-phase electric motor, the machine has a production cost of USD565 with the construction materials being locally available at affordable costs. A cottage mango juice extraction plant based on this technology can provide employment for at least two persons at the same time providing fresh juice at low costs and residual waste as an ingredient for livestock feed manufacturing.
文摘This paper presents modified version of a realistic test tool suitable to Design For Testability （DFT） and Built-ln Self Test （BIST） environments. A comprehensive tool is developed in the form of a test simulator. The simulator is capable of providing a required goal of test for the Circuit Under Test （CUT）. The simulator uses the approach of fault diagnostics with fault grading procedures to provide the optimum tests. The current version of the simulator embeds features of exhaustive and pseudo-random test generation schemes along with the search solutions of cost effective test goals. The simulator provides facilities of realizing all possible pseudo-random sequence generators with all possible combinations of seeds. The tool is developed on a common Personal Computer （PC） platform and hence no special software is required. Thereby, it is a low cost tool hence economical. The tool is very much suitable for determining realistic test sequences for a targeted goal of testing for any CUT. The developed tool incorporates flexible Graphical User Interface （GUI） procedures and can be operated without any special programming skill. The tool is debugged and tested with the results of many bench mark circuits. Further, this developed tool can be utilized for educational purposes for many courses such as fault-tolerant computing, fault diagnosis, digital electronics, and safe-reliable-testable digital logic designs.
文摘Statistical power, number of replicates and experiment complexity of semi-field and field studies on Apis and non-Apis bee species has become a major issue after publication of the draft European Food Safety Authority （EFSA） Guidance on risk assessment of plant protection products （PPP） on bees （Apis mellifera, Bombus spp. and solitary bees）. According to this guidance document, field studies have to be designed to be able to detect significance differences as low as 7% for certain endpoints such as reduction in colony size. This will require an immense number of replicates which is obviously not feasible. In the present study, key endpoints such as mortality, termination rate and number of brood cells in honeybee studies, cocoon production and flight activity in solitary bee studies and number of gynes in bumble bee studies （just to mention some of the endpoints considered） in semi-field studies were analyzed, with Apis mellifera, Bombus terrestris and Osmia bicornis during the past five years （2013-2017）. The results indicate huge differences in the percentage minimal detectable differences （%MDDs） （MDD expressed as median of control value of the endpoint in percent） depending on endpoint and species tested. For honeybee semi-field studies, the lowest %MDDs recorded were between 10% and 15% for the endpoints foraging, number of brood cells and colony strength. The highest %MDDs were observed for the endpoint termination rate, with a %MDD of almost 50%. For the endpoints in bumble bee semi-field studies the %MDDs varied between 17% for bumble bee colony weight and 53% for average mortality during the exposure period in the tunnel. The %MDD for the number of gynes （young queens） was slightly below 25%. For the semi-field solitary bee test system, the %MDDs for the measured endpoints seem to be lower than those for the other two species tested. The %MDDs for the endpoints hatching of offspring, nest occupation and number of cocoons were 8%, 13% and 14%, respectively. Most of the %MDDs were between 10% and 30% indicating clearly that the currently performed experimental design for the semi-field pollinator studies allowed to determine relatively small effects on key study endpoints. The analysis indicated that for all the three bee species tested, the semi-field test design detected low %MDDs for most of the endpoints. It was also observed that detectable differences between the control and PPP treatments were much lower in semi-field test designs than in field studies with these bee species. The “perfect sample size” really does not exist but test design and statistical analysis can be adapted to lower the %MDDs. Measured and simulated （according to Student’s t-test-distribution） data and results showed that statistical evaluations parameter selection （e.g., alpha value）, data transformation （log10） and the number of replicates had a direct effect on the ability of the test design to detect lower or higher %MDD values. It could show that a change of alpha value from 0.05 to 0.1, increases the ability of the studies to detect lower %MDDs. For most of the measured endpoints, increasing the number of replicates e.g., from four to eight, improved the power of the test design by decreasing the %MDD. The reduction magnitude of the %MDD is dependent on the endpoint and selection of statistical parameters such as the alpha value. Parameters that display effects at a biologically relevant scale will be a better indicator for effects than parameters that are able to detect minor differences that are not biologically relevant.
基金This work was supported by National Natural Science Foundation of China under the grant No .60173029 and 60473033
文摘Parity testing is one of the compact testing techniques, which, traditionally, relies on applying all 2^n input combinations to an n-input combinational circuit without need of knowing the implementation of the circuits under test. The faults can be detected just by observing and comparing its parity of whole output of circuit with the expectation one. The way seemed to be less interesting to the test eagineers in the past days, mainly due to the reasons of its exhaustive testing and time-cousuming, which became a barrier as the number of input lines gets growing. However its great facility and convenience in testing still interest to the engineers who need to have a quick look at the qualities of the circuits without generating the test patterns for a given circuit to be tested. In this paper, a new approach called pseudo-parity testing is presented to deal with the dilemma we are facing： i. e. to change an exhaustive parity testing into a non-exhaustive one, followed by a pseudo- parity testable design to help realize the new way of pseudo-parity testing. The idea of pseudo-parity testing presented in this paper may resume its spirits towards its promising future.
基金Sponsored by the Multidisciline Scientific Research Foundation of Harbin Institute of Technology(Grant No.HIT.MD2003.14)the Scientific Research Foundation of Liaoning Provincial Communication Department(Grant No.200516)
文摘In order to achieve an access to strain sensor data with wireless transmission in bridge engineering structure testing, a wireless strain test system is presented based on the resistance strain sensor of networks. The wireless bridge strain test system composed of master station and substation adopts the wireless method to realize the high accuracy data acquisition between the master station and the substation under a reliable communication protocol. The system has been tested in contrast with the present strain apparatus. Results show that the wireless system is high-reliable, and has many characteristics such as high efficiency, good precision, high stability with low cost, and good flexibility, without using the present communication network.
文摘In order to design the relief system size of di-tert-butyl peroxide(DTBP) storage tanks,the runaway re-action of DTBP was simulated by accelerating rate calorimeter(ARC).The results indicated that under adiabatic conditions the initial exothermic temperature was 102.6 ℃,the maximum self-heating rate was 3.095×107 ℃·min-1,the maximum self-heating temperature was 375.9 ℃,and the pressure produced by unit mass was 4.512 MPa·g-1.Judged by ARC test,the emergency relief system for DTBP was a hybrid system.Based on Design Institute for Emergency Relief System(DIERS) method,the releasing mass flow rate W was determined by Leung methods,and the mass velocity G was calculated by two modified Omega methods.The two relief sizes calculated by monograph Omega method and arithmetic Omega method are close,with only 0.63% relative error.The monograph Omega method is more convenient to apply.
基金Supported by the Key Projects of Anhui Provincial Scientific and Technological Program （11010401015） the Key Program of National Natural Science Foundation of China （51134012）
文摘During advanced water detection using the transient electromagnetic method, the exploration effect for water-rich area is often poor due to the interference of bolts that are distributed in different positions in working face. Thus, the study on the interference characteristics of bolts in different states has important directive significance for improving the acquisition quality and data processing method in water detection. Based on the analysis of the distribution laws of magnetic field excited by small multi-turn coincident loop in full space of homogeneity, the test on the interference of bolts has been designed in the mine. Through drilling 18 holes around the overlapping coil in the working face, mass data are collected in order with the posi- tion change and the exposed bolt length. The results of comprehensive data analysis show that the transient electromagnetic field is strongly interfered as the distance between the bolt and the center of the coil is less than 3 m, and the interference varies greatly as the distance varies. On the other hand, the field induced by the bolts can be ignored as the distance exceeds 3 m. The findings can help to improve data acquisition and correction during advanced water detection when using the transient electromagnetic method.
文摘For the conventional single-ended eFuse cell, sensing failures can occur due to a variation of a post-program eFuse resistance during the data retention time and a relatively high program resistance of several kilo ohms. A differential paired eFuse cell is designed which is about half the size smaller in sensing resistance of a programmed eFuse link than the conventional single-ended eFuse cell. Also, a sensing circuit of sense amplifier is proposed, based on D flip-flop structure to implement a simple sensing circuit. Furthermore, a sensing margin test circuit is proposed with variable pull-up loads out of consideration for resistance variation of a programmed eFuse. When an 8 bit eFuse OTP IP is designed with 0.18 ~tm standard CMOS logic of TSMC, the layout dimensions are 229.04 μm ×100.15μm. All the chips function successfully when 20 test chips are tested with a program voltage of 4.2 V.
文摘through the design of teaching aerobics web-based course and application practice, the instructional design process based on B/ S learning are analyzed, and discusses several key problems in the design and teaching. This paper presents the resource based learning aerobics teaching design network course should adapt to the application mode of network teaching and traditional classroom combination; that will provide teaching demonstration, teaching contents for students as well as the function of self testing evaluation and provide the job management, teacher online Q ＆ A, database and knowledge base construction, greatly improving the ＂aerobics＂ teaching efficiency.
