Compacted clay liners are extensively used as barriers to control the upward diffusion of vapors of volatile or semi-volatile organic contaminants released from unsaturated contaminated soils at industrycontaminated s...Compacted clay liners are extensively used as barriers to control the upward diffusion of vapors of volatile or semi-volatile organic contaminants released from unsaturated contaminated soils at industrycontaminated sites.This study aimed to investigate the gas diffusion barrier performance of compacted clayey soils amended with three agents including attapulgite and diatomite individually,and attapulgite/diatomite mixture.The properties including water retention,volumetric shrinkage,gas diffusion,and unconfined compressive strength were evaluated through a series of laboratory tests of amended compacted clayey soils.The results demonstrate that the decrease in volume proportions of interaggregate pores leads to an increase in unconfined compressive strength(qu).Both hydrophilic groups and microstructures of attapulgite and diatomite result in an increase in water retention percent(Wt)of compacted clayey soil specimens after amendment regardless of the type of agent or initial water content(w0).Furthermore,the ratio of the gas diffusion coefficient(De)to the gas diffusion coefficient in the air(Da)was significantly reduced owing to a decrease in volume proportions of inter-aggregate pores,hydrophilic group,and microstructures of attapulgite and diatomite.Scanning electron microscope analyses revealed that rod-shaped attapulgite filled the inter-aggregate pores formed by clay particles,whereas the disc-shaped diatomite particles,characterized by micropores,failed to obstruct the interaggregate pores due to their larger particle size.Mercury intrusion porosimetry(MIP)analyses showed a reduction in pore volume in the inter-aggregate pores,leading to a reduction in the total pore volume for both the attapulgite and attapulgite/diatomite mixture amended clays,which is in accordance with the scanning electron microscope(SEM)results.The findings are pertinent to the practical application of compacted clay liners as gas barriers against the upward migration of volatile or semi-volatile organic contaminants at contaminated sites.展开更多
Exploring high-efficiency and broadband microwave absorption(MA)materials with corrosion resistance and low cost is ur-gently needed for wide practical applications.Herein,the natural porous attapulgite(ATP)nanorods e...Exploring high-efficiency and broadband microwave absorption(MA)materials with corrosion resistance and low cost is ur-gently needed for wide practical applications.Herein,the natural porous attapulgite(ATP)nanorods embedded with TiO_(2)and polyaniline(PANI)nanoparticles are synthesized via heterogeneous precipitation and in-situ polymerization.The obtained PANI-TiO_(2)-ATP one-di-mensional(1D)nanostructures can intertwine into three-dimensional(3D)conductive network,which favors energy dissipation.The min-imum reflection loss(RL_(min))of the PANI-TiO_(2)-ATP coating(20wt%)reaches-49.36 dB at 9.53 GHz,and the effective absorption band-width(EAB)can reach 6.53 GHz with a thickness of 2.1 mm.The excellent MA properties are attributed to interfacial polarization,mul-tiple loss mechanisms,and good impedance matching induced by the synergistic effect of PANI-TiO_(2)nanoparticle shells and ATP nanor-ods.In addition,salt spray and Tafel polarization curve tests reveal that the PANI-TiO_(2)-ATP coating shows outstanding corrosion resist-ance performance.This study provides a low-cost and high-efficiency strategy for constructing 1D nanonetwork composites for MA and corrosion resistance applications using natural porous ATP nanorods as carriers.展开更多
Bio-silica issued from diatom, a microalgae, is attracted increasing attention in material science thanks to its peculiar nanoarchitecture and related properties with versatile applications. The present work is a deep...Bio-silica issued from diatom, a microalgae, is attracted increasing attention in material science thanks to its peculiar nanoarchitecture and related properties with versatile applications. The present work is a deep analysis on morphological and chemical properties of bio-silica issued from fossil origin (diatomaceous earth) and living one (algal paste). An optimization in purification protocol was performed to obtain multiparous bio-silica from its raw media with keeping its original shape entirely. Multiple characterization methods as scanning electronic microscopy (SEM), infrared spectroscopy, x-ray diffraction (DRX), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption and inverse gas chromatography (IGC), were used to check the purification protocol efficiency as well as to gather accurate information on morphology and chemical composition of diatom material obtained in large amount.展开更多
The durability of reinforced concrete structures is greatly influenced by the corrosion of the reinforcement. In addition to air pollution related to the repair of corroded structures, chloride ions are the main facto...The durability of reinforced concrete structures is greatly influenced by the corrosion of the reinforcement. In addition to air pollution related to the repair of corroded structures, chloride ions are the main factors of corrosion of reinforced concrete structures. This study aims to valorize a clay inhibitor against reinforcement corrosion in reinforced concrete. This clay (Attapulgite) was incorporated into reinforced concretes at different percentages of substitution of calcined attapulgite (0%, 5% and 10%) to cement in the formulation. The corrosion inhibitory power of attapulgite is evaluated in reinforced concretes subjected to the action of chloride ions at different intervals in the NaCl solution (1 day, 21 days and 45 days) by electrochemical methods (zero current chronopotentiometry, polarization curves and electrochemical impedance spectroscopy). This study showed that in the presence of chloride ions, the composition based on 10% attapulgite has an appreciable inhibitory effect with an average inhibitory efficiency of 82%.展开更多
The photodisinfection process using biomolded semiconductor photocatalysts can inactivate bacteria in wastewater washing machine samples. The comparative study evaluated the photocatalyst material titanium dioxide (Ti...The photodisinfection process using biomolded semiconductor photocatalysts can inactivate bacteria in wastewater washing machine samples. The comparative study evaluated the photocatalyst material titanium dioxide (TiO2) synthesized with diatomite and biocharcoal biotemplate (TiO2-Biocharcoal and TiO2-Diatomite) in photodisinfection processes using domestic washing machine wastewater samples, the results of bacterial inactivation were above 96%. The efficiency of the photodisinfection process was evaluated by counting the number of colonies of the bacteria. Experiments under LED solar lamps presented similar bacterial inactivation, and a correlation with kinetic models. The kinetic study demonstrated a curved regression, indicating a better fit with the Hom model. A tail at the end of the modeling curve indicates the presence of a high concentration of inactive bacteria in the medium, while a shoulder at the beginning of the curve suggests a heterogeneous sample with a high concentration of gram-positive bacteria. The toxicity tests performed with wastewater samples without light exposure indicated low toxicity for both materials. The study presented promising disinfection results for an accessible and efficient photo-sterilization process of water contaminated with bacteria using abundant solar and renewable energy throughout the national territory. .展开更多
The purpose of this paper is to make a contribution to the use of diatomite as a mineral additive in the composition of compressed earth blocks. The aim is to study the influence of diatomite on the hygrothermal behav...The purpose of this paper is to make a contribution to the use of diatomite as a mineral additive in the composition of compressed earth blocks. The aim is to study the influence of diatomite on the hygrothermal behaviour of composites based on clay soils. For this reason, two clay soils with different physicochemical and mineralogical compositions were incorporated with diatomite at percentages ranging from 5% to 50% with a step of 5 to produce compressed earth blocks. After assessing the hydric and thermal characteristics of the composites, it was found that the incorporation of diatomite into the clay matrix favours the absorption of water by capillary action for all the composites. The diatomite-amended blocks subjected to the rain erosion test were less eroded than the unamended blocks. In addition, BYD composites were found to be more resistant than BTD composites, due to the high percentage of clay in T soil. The thermal conductivity of the latter decreases respectively from 0.72 to 0.29 W/m∙K for BTD composites and from 0.52 to 0.21 W/m∙K for BYD composites. This reduction proves the thermal insulating properties of diatomite. Despite the high capillary absorption capacity of these composites, they have good thermal properties, enabling them to be used in the construction of buildings for improved indoor thermal comfort.展开更多
We demonstrate the synthesis of C-Cl-codoped titania/attapulgite（TiO2/ATT） composites containing a mixture of TiO2 phases by a facile sol-gel method at 70 ℃ using titanium tetraisopropoxide as the TiO2 precursor an...We demonstrate the synthesis of C-Cl-codoped titania/attapulgite（TiO2/ATT） composites containing a mixture of TiO2 phases by a facile sol-gel method at 70 ℃ using titanium tetraisopropoxide as the TiO2 precursor and ATT as a support for the TiO2 nanoparticles.The photocatalytic activity of the C-Cl-codoped TiO2/ATT composites with mixed anatase/brookite/rutile phases obtained at pH= 3.0 was much higher than that of commercially available Degussa P25 for the photocatalytic degradation of acid red G under visible-light irradiation.The excellent photocatalytic activity of the developed composite originates from the nonmetal codoping,which extends the absorption edge of TiO2 into visible region,and the presence of multiple phases,which slow the recombination of photoexcited electron/hole pairs.The formation of hydroxyl radicals during the photocatalytic degradation process was detected by photoluminescence probing using terephthalic acid.A mechanism for photocatalysis over the C-Cl-codoped TiO2/ATT composites was proposed.展开更多
A kind of neat asphalt and three kinds of diatomite asphalt are tested using differential scanning calorimetry（DSC）. The anti-cracking mechanism of diatomite asphalt is analyzed by DSC and the thermal stress restrai...A kind of neat asphalt and three kinds of diatomite asphalt are tested using differential scanning calorimetry（DSC）. The anti-cracking mechanism of diatomite asphalt is analyzed by DSC and the thermal stress restrained specimen test（TSRST） of the asphalt mixtures. The results show that the low temperature performance of diatomite asphalt is better than that of neat asphalt. The glass transition temperature can reflect the low temperature performance of the diatomite asphalt better and has a good relationship with breaking temperatures. Besides, the TSRST, the bending test, the compressing test and the contraction coefficient test are used to study the low temperature performance of the diatomite asphalt mixture. The results prove that the low temperature performance of the diatomite asphalt mixture is better than that of the neat asphalt mixture. The critical bending strain energy density and the compressing strain energy density of the diatomite asphalt mixture are greater than those of the neat asphalt mixture. After adding diatomite to the asphalt mixture, the contraction coefficient is reduced. Based on the above results, the anti-cracking mechanism of the diatomite asphalt mixture is analyzed from the angle of contraction performance and breaking energy.展开更多
Organo-attapulgite was obtained by modifying attapulgite with hexadecyltrimethyl ammonium bromide.A new organo-attapulgite based superabsorbent composite was prepared by polymerization of organo-attapulgite dispersed ...Organo-attapulgite was obtained by modifying attapulgite with hexadecyltrimethyl ammonium bromide.A new organo-attapulgite based superabsorbent composite was prepared by polymerization of organo-attapulgite dispersed acrylamide,using N,N′-methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator.The structure,morphology,thermal stability of organo-attapulgite and the composite were characterized by FTIR,XRD,SEM,TEM and TGA,respectively.The results indicated that a nanocomposite was successfully obtained after incorporating organo-attapulgite into the polyacrylamide network.The thermal stability and water absorbency of the nanocomposite were improved greatly after the organification of attapulgite.Water absorbencies for the nanocomposite incorporated with 10 wt% HDTMA-APT in distilled water and in a 0.9 wt% NaCl solution were 2803 g g -1 and 121 g g -1,respectively.展开更多
Diatomite-based porous ceramics were adopted as carriers to immobilize nano-TiO2 via a hydrolysis-deposition technique. The thermal degradation of as-prepared composites was investigated using thermogravimetric-differ...Diatomite-based porous ceramics were adopted as carriers to immobilize nano-TiO2 via a hydrolysis-deposition technique. The thermal degradation of as-prepared composites was investigated using thermogravimetric-differential thermal analysis, and the phase and microstructure were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and transmission electron microscopy. The results indicated that the carriers were encapsulated by nano-TiO2 with a thickness of 300-450 nm. The main crystalline phase of TiO2 calcined at 650~C was anatase, and the average grain size was 8.3 nm. The FT-IR absorption bands at 955.38 cm1 suggested that new chemical bonds among Ti, O, and Si had formed in the composites. The photocatalytic （PC） activity of the composites was investigated un- der UV irradiation. Furthermore, the photodegradation kinetics of formaldehyde was investigated using the composites as the cores of an air cleaner. A kinetics study showed that the reaction rate constants of the gas-phase PC reaction of formaldehyde were k = 0.576 mg＇m3·min^-1 and K = 0.048 m3/mg.展开更多
The surface ion-imprinting concept and chitosan incorporated sol-gel process were applied to the synthesis of a new attapulgitesupported polymer for selective separation of Ce（III） from aqueous solution. The imprint...The surface ion-imprinting concept and chitosan incorporated sol-gel process were applied to the synthesis of a new attapulgitesupported polymer for selective separation of Ce（III） from aqueous solution. The imprinting mechanism of prepared ion-imprinted polymer were discussed with the Characteristics of FT-IR and SEM. Results from the experiments of adsorption capacity and selectivity suggested that ion-imprinted polymer offered a fast kinetics for the adsorption of Ce（III） under the optimum conditions. Its maximum adsorption capacity was 38.02 mg/g, and the selective recognition towards Ce（III） was much higher than that of the non-imprinted polymer and attapulgite. The prepared functional polymer was shown to be promising for selective separation and enrichment of trace Ce（III） in environmental samples. ？2009 Yong Sheng Yan. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
We improved the overall performance of fast-growing poplar by utilizing a low-cost, effective and simple method. The fast-growing poplar was modified by a vacuum-pressure impregnation method with three types of modifi...We improved the overall performance of fast-growing poplar by utilizing a low-cost, effective and simple method. The fast-growing poplar was modified by a vacuum-pressure impregnation method with three types of modification solutions composed of phe- nol-melamine-formaldehyde （PMF） co-condensed resin, diatomite, and 3-aminopropyl （diethoxy） methylsilane. We measured the weight percent gain （WPG）, bulking, leaching, anti-swelling efficiency （ASE）, wa- ter-repellent effectiveness （WRE）, and oxygen index of the modified specimens. All of the wood physical properties, which are beneficial for human uses, were significantly improved by the treatment. We improved various characteristics of wood and the oxygen index of poplar above 48.6% after the modification using diatomite and PMF co-condensed resin.展开更多
The feasibility of utilizing molybdenum tailing and diatomite as siliceous materials to prepare calcium silicate board was explored.The influences of molybdenum tailing/diatomite proportion on hydration characteristic...The feasibility of utilizing molybdenum tailing and diatomite as siliceous materials to prepare calcium silicate board was explored.The influences of molybdenum tailing/diatomite proportion on hydration characteristics,thermal conductivity,water absorption,flexural strength and moisture adsorption-desorption property of calcium silicate board were investigated in detail.The experimental results reveal that molybdenum tailing is environmentally friendly to prepare building materials.The main hydration products in calcium silicate board under autoclaved condition are C-S-H with low crystallinity and tobermorite.Molybdenum tailing is favorable to the formation of tobermorite.The flexural strength and bulk density of the calcium silicate board gradually increase when the content of molybdenum tailing increases.Netlike C-S-H is formed with the increase of diatomite content during autoclaved curing process,resulting in the enhancement of moisture adsorptiondesorption performance and the reduction of thermal conductivity.The optimal content of molybdenum tailing is 20%,furthermore,the flexual strength and thermal conductivity of calcium silicate board at this content meet the Chinese standard JC/T564.1-2008.展开更多
The purpose of this work is to study the possibility of anionic dyes Reactive Red M-8B（RR） and Direct Green B（DG） adsorbed on chitosan-modified diatomite. The characteristics of adsorbent, adsorption isotherms and...The purpose of this work is to study the possibility of anionic dyes Reactive Red M-8B（RR） and Direct Green B（DG） adsorbed on chitosan-modified diatomite. The characteristics of adsorbent, adsorption isotherms and the influence of adsorption time, temperature and pH were researched in this work. The results show that the mo- dified diatomite had a much better adsorption capability than the natural diatomite. The adsorption capacities of chitosan-modified diatomite for RR and DG were 94.46 and 137.0 mg/g, respectively. Both adsorption time and adsorption temperature provided a positive effect on the dye adsorption. Within the experimental pH range, the adsorbance was enhanced at lower pH but reduced sharply at high pH. On the basis of the experimental results and discussion, electrostatic attraction is considered as the main mechanism of this chemisorption.展开更多
Diatomite is a kind of natural low-cost mineral material. It has a number of unique physical properties and has been widely used as an adsorbent in wastewater treatment. This study was conducted to investigate the aer...Diatomite is a kind of natural low-cost mineral material. It has a number of unique physical properties and has been widely used as an adsorbent in wastewater treatment. This study was conducted to investigate the aerobic biodegradation of coal gasification wastewater with and without diatomite addition. Experimental results indicated that diatomite added in the activated sludge system could promote the biomass and also enhance the performance of the sludge settling. The average mixed-liquor volatile suspended solids （MLVSS） is increased from 4055 mg.L^-1 to 4518 mg.L^-1 and the average settling volume （SV） are changed only from 45.9% to 47.1%. Diatomite additive could enhance the efficiency of chemical oxygen demand （COD） and total phenols removal from the wastewater. The COD removal increased from 73.3% to near 80% and the total phenols removal increased from 81.4% to 85.8%. The mechanisms of the increase of biomass and pollutants removal may correlates to the improvement of bioavailability and sludge settlement characteristics by diatomite added. Micrograph of the sludge in the diatomite-activated sludge system indicated that the diatomite added could be the carrier of the microbe and also affect the biomass and pollutant removal.展开更多
Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load pheno...Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load phenolic resin, carbonization and activation isolated air. The influences of impregnation, curing, carbonization, activation etc. on the material property were discussed. The iodine value, SEM, elemental analyzer, BET and spectrum analysis chart were used to characterize the microstructures and performance of material at different conditions. The results showed that the excellent comprehensive property of activated carbon functional ceramic was gained when it adsorbed phenolic resin in 4 h under vacuum condition at curing temperature of 150 ℃ for 0.5 h and carbonization temperature of 600 ℃ for 1.0 h, and then put into 25wt% KOH for 4.0 h at activation temperature of 700 ℃ for 1.5 h. The iodine value is 176.9 mg/g, the specific surface area can reach 86.3 m2/g and the yield of carbonization is 50.48%.展开更多
Diatomite was used as raw material to prepare sodium silicate with a modulus of 3.1 by alkali dissolution method and the resulted sodium silicate solution was employed as a precursor. Methyl methaerylate monomers were...Diatomite was used as raw material to prepare sodium silicate with a modulus of 3.1 by alkali dissolution method and the resulted sodium silicate solution was employed as a precursor. Methyl methaerylate monomers were introduced in wet gels through solution-immersion, and upon heating at 70 ℃, the mesoporous surfaces throughout the skeletal framework were coated with the polymer layer. PMMA modified silica aerogels were successfully synthesized via ambient pressure drying. The properties were investigated by FT- IR, NMR, TGA, nitrogen adsorption-desorption, FESEM and nano-indentation, etc. Results indicate that with the increasing of PMMA incorporated into silica aerogels, the bulk density and the BET surface area increase, the porosity decreases. Through the observation of FESEM, it is found that the interconnecting pores and the big pores add, the pore size distribution expands from 5-17 to 28-150 urn. By comparison, the PMMA modified silica aerogels achieve a 52-fold increase in hardness and a 10-fold increase in modulus.展开更多
Li-ion batteries(LIBs)have demonstrated great promise in electric vehicles and hybrid electric vehicles.However,commercial graphite materials,the current predominant anodes in LIBs,have a low theoretical capacity of o...Li-ion batteries(LIBs)have demonstrated great promise in electric vehicles and hybrid electric vehicles.However,commercial graphite materials,the current predominant anodes in LIBs,have a low theoretical capacity of only 372 mAh·g?1,which cannot meet the everincreasing demand of LIBs for high energy density.Nanoscale Si is considered an ideal form of Si for the fabrication of LIB anodes as Si–C composites.Synthesis of nanoscale Si in a facile,cost-effective way,however,still poses a great challenge.In this work,nanoscale Si was prepared by a controlled magnesiothermic reaction using diatomite as the Si source.It was found that the nanoscale Si prepared under optimized conditions(800°C,10 h)can deliver a high initial specific capacity(3053 mAh·g?1 on discharge,2519 mAh·g?1 on charge)with a high first coulombic efficiency(82.5%).When using sand-milled diatomite as a precursor,the obtained nanoscale Si exhibited a well-dispersed morphology and had a higher first coulombic efficiency(85.6%).The Si–C(Si:graphite=1:7 in weight)composite using Si from the sand-milled diatomite demonstrated a high specific capacity(over 700 mAh·g?1 at 100 mA·g?1),good rate capability(587 mAh·g?1 at 500 mA·g?1),and a long cycle life(480 mAh·g?1 after 200 cycles at 500 mA·g?1).This work gives a facile method to synthesize nanoscale Si with both high capacity and high first coulombic efficiency.展开更多
基金the funding support from the National Natural Science Foundation of China(Grant No.42177133)the Primary Research and Development Plan of Jiangsu Province(Grant No.BE2022830)the Primary Research and Development Plan of Anhui Province(Grant No.2023t07020018).
文摘Compacted clay liners are extensively used as barriers to control the upward diffusion of vapors of volatile or semi-volatile organic contaminants released from unsaturated contaminated soils at industrycontaminated sites.This study aimed to investigate the gas diffusion barrier performance of compacted clayey soils amended with three agents including attapulgite and diatomite individually,and attapulgite/diatomite mixture.The properties including water retention,volumetric shrinkage,gas diffusion,and unconfined compressive strength were evaluated through a series of laboratory tests of amended compacted clayey soils.The results demonstrate that the decrease in volume proportions of interaggregate pores leads to an increase in unconfined compressive strength(qu).Both hydrophilic groups and microstructures of attapulgite and diatomite result in an increase in water retention percent(Wt)of compacted clayey soil specimens after amendment regardless of the type of agent or initial water content(w0).Furthermore,the ratio of the gas diffusion coefficient(De)to the gas diffusion coefficient in the air(Da)was significantly reduced owing to a decrease in volume proportions of inter-aggregate pores,hydrophilic group,and microstructures of attapulgite and diatomite.Scanning electron microscope analyses revealed that rod-shaped attapulgite filled the inter-aggregate pores formed by clay particles,whereas the disc-shaped diatomite particles,characterized by micropores,failed to obstruct the interaggregate pores due to their larger particle size.Mercury intrusion porosimetry(MIP)analyses showed a reduction in pore volume in the inter-aggregate pores,leading to a reduction in the total pore volume for both the attapulgite and attapulgite/diatomite mixture amended clays,which is in accordance with the scanning electron microscope(SEM)results.The findings are pertinent to the practical application of compacted clay liners as gas barriers against the upward migration of volatile or semi-volatile organic contaminants at contaminated sites.
基金support from the National Key Research and Development Program of China(No.2021YFB3701503)the Key Research and Development Program of Ningbo,China(No.2023Z107)+1 种基金the Jiangsu Key R&D program,China(No.BE2019072)the special project of Gansu regional science and technology cooperation,China(No.20JR10 QA579).
文摘Exploring high-efficiency and broadband microwave absorption(MA)materials with corrosion resistance and low cost is ur-gently needed for wide practical applications.Herein,the natural porous attapulgite(ATP)nanorods embedded with TiO_(2)and polyaniline(PANI)nanoparticles are synthesized via heterogeneous precipitation and in-situ polymerization.The obtained PANI-TiO_(2)-ATP one-di-mensional(1D)nanostructures can intertwine into three-dimensional(3D)conductive network,which favors energy dissipation.The min-imum reflection loss(RL_(min))of the PANI-TiO_(2)-ATP coating(20wt%)reaches-49.36 dB at 9.53 GHz,and the effective absorption band-width(EAB)can reach 6.53 GHz with a thickness of 2.1 mm.The excellent MA properties are attributed to interfacial polarization,mul-tiple loss mechanisms,and good impedance matching induced by the synergistic effect of PANI-TiO_(2)nanoparticle shells and ATP nanor-ods.In addition,salt spray and Tafel polarization curve tests reveal that the PANI-TiO_(2)-ATP coating shows outstanding corrosion resist-ance performance.This study provides a low-cost and high-efficiency strategy for constructing 1D nanonetwork composites for MA and corrosion resistance applications using natural porous ATP nanorods as carriers.
文摘Bio-silica issued from diatom, a microalgae, is attracted increasing attention in material science thanks to its peculiar nanoarchitecture and related properties with versatile applications. The present work is a deep analysis on morphological and chemical properties of bio-silica issued from fossil origin (diatomaceous earth) and living one (algal paste). An optimization in purification protocol was performed to obtain multiparous bio-silica from its raw media with keeping its original shape entirely. Multiple characterization methods as scanning electronic microscopy (SEM), infrared spectroscopy, x-ray diffraction (DRX), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption and inverse gas chromatography (IGC), were used to check the purification protocol efficiency as well as to gather accurate information on morphology and chemical composition of diatom material obtained in large amount.
文摘The durability of reinforced concrete structures is greatly influenced by the corrosion of the reinforcement. In addition to air pollution related to the repair of corroded structures, chloride ions are the main factors of corrosion of reinforced concrete structures. This study aims to valorize a clay inhibitor against reinforcement corrosion in reinforced concrete. This clay (Attapulgite) was incorporated into reinforced concretes at different percentages of substitution of calcined attapulgite (0%, 5% and 10%) to cement in the formulation. The corrosion inhibitory power of attapulgite is evaluated in reinforced concretes subjected to the action of chloride ions at different intervals in the NaCl solution (1 day, 21 days and 45 days) by electrochemical methods (zero current chronopotentiometry, polarization curves and electrochemical impedance spectroscopy). This study showed that in the presence of chloride ions, the composition based on 10% attapulgite has an appreciable inhibitory effect with an average inhibitory efficiency of 82%.
文摘The photodisinfection process using biomolded semiconductor photocatalysts can inactivate bacteria in wastewater washing machine samples. The comparative study evaluated the photocatalyst material titanium dioxide (TiO2) synthesized with diatomite and biocharcoal biotemplate (TiO2-Biocharcoal and TiO2-Diatomite) in photodisinfection processes using domestic washing machine wastewater samples, the results of bacterial inactivation were above 96%. The efficiency of the photodisinfection process was evaluated by counting the number of colonies of the bacteria. Experiments under LED solar lamps presented similar bacterial inactivation, and a correlation with kinetic models. The kinetic study demonstrated a curved regression, indicating a better fit with the Hom model. A tail at the end of the modeling curve indicates the presence of a high concentration of inactive bacteria in the medium, while a shoulder at the beginning of the curve suggests a heterogeneous sample with a high concentration of gram-positive bacteria. The toxicity tests performed with wastewater samples without light exposure indicated low toxicity for both materials. The study presented promising disinfection results for an accessible and efficient photo-sterilization process of water contaminated with bacteria using abundant solar and renewable energy throughout the national territory. .
文摘The purpose of this paper is to make a contribution to the use of diatomite as a mineral additive in the composition of compressed earth blocks. The aim is to study the influence of diatomite on the hygrothermal behaviour of composites based on clay soils. For this reason, two clay soils with different physicochemical and mineralogical compositions were incorporated with diatomite at percentages ranging from 5% to 50% with a step of 5 to produce compressed earth blocks. After assessing the hydric and thermal characteristics of the composites, it was found that the incorporation of diatomite into the clay matrix favours the absorption of water by capillary action for all the composites. The diatomite-amended blocks subjected to the rain erosion test were less eroded than the unamended blocks. In addition, BYD composites were found to be more resistant than BTD composites, due to the high percentage of clay in T soil. The thermal conductivity of the latter decreases respectively from 0.72 to 0.29 W/m∙K for BTD composites and from 0.52 to 0.21 W/m∙K for BYD composites. This reduction proves the thermal insulating properties of diatomite. Despite the high capillary absorption capacity of these composites, they have good thermal properties, enabling them to be used in the construction of buildings for improved indoor thermal comfort.
基金supported by the National Basic Research Program of China (973 Program, 2007CB613302)the Natural Science Foundation of Hubei Province (2016CFA078)~~
文摘We demonstrate the synthesis of C-Cl-codoped titania/attapulgite（TiO2/ATT） composites containing a mixture of TiO2 phases by a facile sol-gel method at 70 ℃ using titanium tetraisopropoxide as the TiO2 precursor and ATT as a support for the TiO2 nanoparticles.The photocatalytic activity of the C-Cl-codoped TiO2/ATT composites with mixed anatase/brookite/rutile phases obtained at pH= 3.0 was much higher than that of commercially available Degussa P25 for the photocatalytic degradation of acid red G under visible-light irradiation.The excellent photocatalytic activity of the developed composite originates from the nonmetal codoping,which extends the absorption edge of TiO2 into visible region,and the presence of multiple phases,which slow the recombination of photoexcited electron/hole pairs.The formation of hydroxyl radicals during the photocatalytic degradation process was detected by photoluminescence probing using terephthalic acid.A mechanism for photocatalysis over the C-Cl-codoped TiO2/ATT composites was proposed.
基金The National Natural Science Foundation of China(No.50778057)
文摘A kind of neat asphalt and three kinds of diatomite asphalt are tested using differential scanning calorimetry（DSC）. The anti-cracking mechanism of diatomite asphalt is analyzed by DSC and the thermal stress restrained specimen test（TSRST） of the asphalt mixtures. The results show that the low temperature performance of diatomite asphalt is better than that of neat asphalt. The glass transition temperature can reflect the low temperature performance of the diatomite asphalt better and has a good relationship with breaking temperatures. Besides, the TSRST, the bending test, the compressing test and the contraction coefficient test are used to study the low temperature performance of the diatomite asphalt mixture. The results prove that the low temperature performance of the diatomite asphalt mixture is better than that of the neat asphalt mixture. The critical bending strain energy density and the compressing strain energy density of the diatomite asphalt mixture are greater than those of the neat asphalt mixture. After adding diatomite to the asphalt mixture, the contraction coefficient is reduced. Based on the above results, the anti-cracking mechanism of the diatomite asphalt mixture is analyzed from the angle of contraction performance and breaking energy.
文摘Organo-attapulgite was obtained by modifying attapulgite with hexadecyltrimethyl ammonium bromide.A new organo-attapulgite based superabsorbent composite was prepared by polymerization of organo-attapulgite dispersed acrylamide,using N,N′-methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator.The structure,morphology,thermal stability of organo-attapulgite and the composite were characterized by FTIR,XRD,SEM,TEM and TGA,respectively.The results indicated that a nanocomposite was successfully obtained after incorporating organo-attapulgite into the polyacrylamide network.The thermal stability and water absorbency of the nanocomposite were improved greatly after the organification of attapulgite.Water absorbencies for the nanocomposite incorporated with 10 wt% HDTMA-APT in distilled water and in a 0.9 wt% NaCl solution were 2803 g g -1 and 121 g g -1,respectively.
基金financially supported by the National Natural Science Foundation of China (No. 50708037)the National Science Fund for Excellent Young Scholars of China (No. 51522402)+1 种基金the Science and Technology Research Projects in Zhengzhou (No. 141PPTGG388)the National Innovation and Entrepreneurship Training Program of the Undergraduate (No. 201610078034)
文摘Diatomite-based porous ceramics were adopted as carriers to immobilize nano-TiO2 via a hydrolysis-deposition technique. The thermal degradation of as-prepared composites was investigated using thermogravimetric-differential thermal analysis, and the phase and microstructure were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and transmission electron microscopy. The results indicated that the carriers were encapsulated by nano-TiO2 with a thickness of 300-450 nm. The main crystalline phase of TiO2 calcined at 650~C was anatase, and the average grain size was 8.3 nm. The FT-IR absorption bands at 955.38 cm1 suggested that new chemical bonds among Ti, O, and Si had formed in the composites. The photocatalytic （PC） activity of the composites was investigated un- der UV irradiation. Furthermore, the photodegradation kinetics of formaldehyde was investigated using the composites as the cores of an air cleaner. A kinetics study showed that the reaction rate constants of the gas-phase PC reaction of formaldehyde were k = 0.576 mg＇m3·min^-1 and K = 0.048 m3/mg.
基金supported by the National Natural Science Foundation of China(No.20877036).
文摘The surface ion-imprinting concept and chitosan incorporated sol-gel process were applied to the synthesis of a new attapulgitesupported polymer for selective separation of Ce（III） from aqueous solution. The imprinting mechanism of prepared ion-imprinted polymer were discussed with the Characteristics of FT-IR and SEM. Results from the experiments of adsorption capacity and selectivity suggested that ion-imprinted polymer offered a fast kinetics for the adsorption of Ce（III） under the optimum conditions. Its maximum adsorption capacity was 38.02 mg/g, and the selective recognition towards Ce（III） was much higher than that of the non-imprinted polymer and attapulgite. The prepared functional polymer was shown to be promising for selective separation and enrichment of trace Ce（III） in environmental samples. ？2009 Yong Sheng Yan. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
基金supported by Program for New Century Excellent Talents in University(NCET-10-0311)the National Natural Science Foundation of China(31000271)the Fundamental Research Funds for the Central Universities(DL11BB29)
文摘We improved the overall performance of fast-growing poplar by utilizing a low-cost, effective and simple method. The fast-growing poplar was modified by a vacuum-pressure impregnation method with three types of modification solutions composed of phe- nol-melamine-formaldehyde （PMF） co-condensed resin, diatomite, and 3-aminopropyl （diethoxy） methylsilane. We measured the weight percent gain （WPG）, bulking, leaching, anti-swelling efficiency （ASE）, wa- ter-repellent effectiveness （WRE）, and oxygen index of the modified specimens. All of the wood physical properties, which are beneficial for human uses, were significantly improved by the treatment. We improved various characteristics of wood and the oxygen index of poplar above 48.6% after the modification using diatomite and PMF co-condensed resin.
基金Funded by the National Key R&D Program of China(No.2017YFC0703206).
文摘The feasibility of utilizing molybdenum tailing and diatomite as siliceous materials to prepare calcium silicate board was explored.The influences of molybdenum tailing/diatomite proportion on hydration characteristics,thermal conductivity,water absorption,flexural strength and moisture adsorption-desorption property of calcium silicate board were investigated in detail.The experimental results reveal that molybdenum tailing is environmentally friendly to prepare building materials.The main hydration products in calcium silicate board under autoclaved condition are C-S-H with low crystallinity and tobermorite.Molybdenum tailing is favorable to the formation of tobermorite.The flexural strength and bulk density of the calcium silicate board gradually increase when the content of molybdenum tailing increases.Netlike C-S-H is formed with the increase of diatomite content during autoclaved curing process,resulting in the enhancement of moisture adsorptiondesorption performance and the reduction of thermal conductivity.The optimal content of molybdenum tailing is 20%,furthermore,the flexual strength and thermal conductivity of calcium silicate board at this content meet the Chinese standard JC/T564.1-2008.
基金Supported by the Research Fund of Environmental Protection Bureau in Jilin Province,China(No.2007-13)
文摘The purpose of this work is to study the possibility of anionic dyes Reactive Red M-8B（RR） and Direct Green B（DG） adsorbed on chitosan-modified diatomite. The characteristics of adsorbent, adsorption isotherms and the influence of adsorption time, temperature and pH were researched in this work. The results show that the mo- dified diatomite had a much better adsorption capability than the natural diatomite. The adsorption capacities of chitosan-modified diatomite for RR and DG were 94.46 and 137.0 mg/g, respectively. Both adsorption time and adsorption temperature provided a positive effect on the dye adsorption. Within the experimental pH range, the adsorbance was enhanced at lower pH but reduced sharply at high pH. On the basis of the experimental results and discussion, electrostatic attraction is considered as the main mechanism of this chemisorption.
基金Supported by the Shanghai Committee of Education (07ZZ158)
文摘Diatomite is a kind of natural low-cost mineral material. It has a number of unique physical properties and has been widely used as an adsorbent in wastewater treatment. This study was conducted to investigate the aerobic biodegradation of coal gasification wastewater with and without diatomite addition. Experimental results indicated that diatomite added in the activated sludge system could promote the biomass and also enhance the performance of the sludge settling. The average mixed-liquor volatile suspended solids （MLVSS） is increased from 4055 mg.L^-1 to 4518 mg.L^-1 and the average settling volume （SV） are changed only from 45.9% to 47.1%. Diatomite additive could enhance the efficiency of chemical oxygen demand （COD） and total phenols removal from the wastewater. The COD removal increased from 73.3% to near 80% and the total phenols removal increased from 81.4% to 85.8%. The mechanisms of the increase of biomass and pollutants removal may correlates to the improvement of bioavailability and sludge settlement characteristics by diatomite added. Micrograph of the sludge in the diatomite-activated sludge system indicated that the diatomite added could be the carrier of the microbe and also affect the biomass and pollutant removal.
基金Sponsored by the 2007 Fujian University and College New Century Excellent Talent Support Program (No. XSJRC2007-17)Natural Science Foundation of Fujian Province (No. 2010J01279)
文摘Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load phenolic resin, carbonization and activation isolated air. The influences of impregnation, curing, carbonization, activation etc. on the material property were discussed. The iodine value, SEM, elemental analyzer, BET and spectrum analysis chart were used to characterize the microstructures and performance of material at different conditions. The results showed that the excellent comprehensive property of activated carbon functional ceramic was gained when it adsorbed phenolic resin in 4 h under vacuum condition at curing temperature of 150 ℃ for 0.5 h and carbonization temperature of 600 ℃ for 1.0 h, and then put into 25wt% KOH for 4.0 h at activation temperature of 700 ℃ for 1.5 h. The iodine value is 176.9 mg/g, the specific surface area can reach 86.3 m2/g and the yield of carbonization is 50.48%.
基金Supported by the the National Natural Science Foundation of China(No.51278086)Petro China Innovation Fundation(No.2013D-5006-0606)+3 种基金the Program for New Century Excellent Talents in University by Ministry of Education of the People’s Republic of China(No.NCET-12-0084)Liaoning BaiQianWan Talents of Science and Technology Program(No.2012921073)Henan Open and Cooperation Project of Scienceand Technology(No.142106000023)Dalian Plan Projects of Science and Technology(No.2013A16GX113)
文摘Diatomite was used as raw material to prepare sodium silicate with a modulus of 3.1 by alkali dissolution method and the resulted sodium silicate solution was employed as a precursor. Methyl methaerylate monomers were introduced in wet gels through solution-immersion, and upon heating at 70 ℃, the mesoporous surfaces throughout the skeletal framework were coated with the polymer layer. PMMA modified silica aerogels were successfully synthesized via ambient pressure drying. The properties were investigated by FT- IR, NMR, TGA, nitrogen adsorption-desorption, FESEM and nano-indentation, etc. Results indicate that with the increasing of PMMA incorporated into silica aerogels, the bulk density and the BET surface area increase, the porosity decreases. Through the observation of FESEM, it is found that the interconnecting pores and the big pores add, the pore size distribution expands from 5-17 to 28-150 urn. By comparison, the PMMA modified silica aerogels achieve a 52-fold increase in hardness and a 10-fold increase in modulus.
基金the National Natural Science Foundation of China(No.51572238)Zhejiang Provincial Natural Science Foundation(No.LY19E020013)the Joint Research Project of Zhejiang University with Zotye Automobile Corporation Limited on Si-Based Anode Materials(No.P-ZH-2018-003).
文摘Li-ion batteries(LIBs)have demonstrated great promise in electric vehicles and hybrid electric vehicles.However,commercial graphite materials,the current predominant anodes in LIBs,have a low theoretical capacity of only 372 mAh·g?1,which cannot meet the everincreasing demand of LIBs for high energy density.Nanoscale Si is considered an ideal form of Si for the fabrication of LIB anodes as Si–C composites.Synthesis of nanoscale Si in a facile,cost-effective way,however,still poses a great challenge.In this work,nanoscale Si was prepared by a controlled magnesiothermic reaction using diatomite as the Si source.It was found that the nanoscale Si prepared under optimized conditions(800°C,10 h)can deliver a high initial specific capacity(3053 mAh·g?1 on discharge,2519 mAh·g?1 on charge)with a high first coulombic efficiency(82.5%).When using sand-milled diatomite as a precursor,the obtained nanoscale Si exhibited a well-dispersed morphology and had a higher first coulombic efficiency(85.6%).The Si–C(Si:graphite=1:7 in weight)composite using Si from the sand-milled diatomite demonstrated a high specific capacity(over 700 mAh·g?1 at 100 mA·g?1),good rate capability(587 mAh·g?1 at 500 mA·g?1),and a long cycle life(480 mAh·g?1 after 200 cycles at 500 mA·g?1).This work gives a facile method to synthesize nanoscale Si with both high capacity and high first coulombic efficiency.
