With the air gap magnetic field distribution of surface mounted permanent magnet （PM） motors obtained using an analytical technique, the instantaneous electromagnetic torque and its corresponding components are inve...With the air gap magnetic field distribution of surface mounted permanent magnet （PM） motors obtained using an analytical technique, the instantaneous electromagnetic torque and its corresponding components are investigated with the Maxwell stress tensor method. Accurate results can easily be achieved using the proposed method without using the tedious finite element analysis （FEA）. In this paper, the electromagnetic torque of a surface mounted PM motor with two phases energized is decomposed into four torque components. This technique is useful not only for the design and optimization of the permanent magnet motor, but also for the choice of control strategy.展开更多
This paper presents an analytical method to design the high-efficiency surface permanent magnet synchronous motor(SPMSM)or generator(SPMSG).The air-gap and permanent magnet size can be approximately determined based o...This paper presents an analytical method to design the high-efficiency surface permanent magnet synchronous motor(SPMSM)or generator(SPMSG).The air-gap and permanent magnet size can be approximately determined based on our mathematics model,which is the most important part of SPMSM design.From our method,we can know that motor’s power out torque is related to the torque angle that we selected in our design and it affects the air-gap and permanent magnet size.If we choose a low torque angle,the motor or generator’s overload power handing capability will increase.The embrace value has a vital place in designing a motor or generator due to its effects on air gap flux density,cogging torque,efficiency and so on.In order to avoid the knee effect,the working point of the permanent magnet we selected in the design should be bigger than 0.5.The developed 36 slots,4 poles,surface mound permanent generator is proposed.The corresponding finite element analysis(FEA)model is built based on our design method.Structure optimization includes stator and rotor structure size,permanent magnet size,magnetic bridge and air gap length which are analyzed and simulated by ANSYS Maxwell 2D FEA.Thermal analysis is conducted,and the housing of the alternator is designed.The alternator prototype is fabricated and tested based on our design.展开更多
A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly forme...A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.展开更多
The surface-mounted and interior permanent magnet synchronous motor(SIPMSM)has the characteristics of multiple variables,strong coupling and nonlinearity.In order to improve the performance of SIPMSM,this paper presen...The surface-mounted and interior permanent magnet synchronous motor(SIPMSM)has the characteristics of multiple variables,strong coupling and nonlinearity.In order to improve the performance of SIPMSM,this paper presents a multi-objective optimal design process using Taguchi and response surface methodology(RSM).The peak value of cogging torque(PVCT),ratio value of average torque and permanent magnet weight(RTW),torque ripple and back-EMF total harmonics distortion(ETHD)are selected as optimization goals.The experiment matrix is established by Taguchi method,and analyzed the tendency and proportion of the effect of the optimization parameters on SIPMSM performance.The rules of choosing multi-objective optimization parameters are obtained.The least-squares method is used to establish the optimal objective function,and RSM is used to obtain the resolutions of the optimization objective function.Comparing the initial performance with optimized performance verifies the effectiveness of the proposed method.展开更多
In this paper,a design is presented for a high-speed,high-power motor for a four-legged robot actuator that was optimized using the weighted sum method(WSM)based on the Taguchi method,and the response surface method(R...In this paper,a design is presented for a high-speed,high-power motor for a four-legged robot actuator that was optimized using the weighted sum method(WSM)based on the Taguchi method,and the response surface method(RSM).First,output torque,torque constant,torque ripple,and efficiency were selected as objective functions for the optimized design.The sampling method was implemented to use a mixed orthogonal array and the single response characteristics of each objective function were compared using the Taguchi method.Moreover,to consider the multi-response characteristic of the objective functions,WSM was applied.Second,the 2D finite element analysis result of the RSM was compared with that using the WSM.Finally,an experiment was carried out on the manufactured motor and the optimized model is presented here.展开更多
A novel nonlinear model for surface permanent magnet synchronous motors（SPMSMs） is adopted to estimate the initial rotor position for hybrid electric vehicles（HEVs）. Usually, the accuracy of initial rotor position...A novel nonlinear model for surface permanent magnet synchronous motors（SPMSMs） is adopted to estimate the initial rotor position for hybrid electric vehicles（HEVs）. Usually, the accuracy of initial rotor position estimation for SPMSMs relies on magnetic saturation. To verify the saturation effect, the transient finite element analysis（FEA） model is presented first. Hybrid injection of a static voltage vector（SVV） superimposed with a high-frequency rotating voltage is proposed. The magnetic polarity is roughly identified with the aid of the saturation evaluation function, based on which an estimation of the position is performed. During this procedure, a special demodulation is suggested to extract signals of iron core saturation and rotor position. A Simulink/MATLAB platform for SPMSMs at standstill is constituted, and the effectiveness of the proposed strategy is verified. The proposed method is also validated by experimental results of an SPMSM drive.展开更多
基金Project supported by the Science Foundation of Shanghai Municipal Commission of Education （Grant No.04AB30）
文摘With the air gap magnetic field distribution of surface mounted permanent magnet （PM） motors obtained using an analytical technique, the instantaneous electromagnetic torque and its corresponding components are investigated with the Maxwell stress tensor method. Accurate results can easily be achieved using the proposed method without using the tedious finite element analysis （FEA）. In this paper, the electromagnetic torque of a surface mounted PM motor with two phases energized is decomposed into four torque components. This technique is useful not only for the design and optimization of the permanent magnet motor, but also for the choice of control strategy.
文摘This paper presents an analytical method to design the high-efficiency surface permanent magnet synchronous motor(SPMSM)or generator(SPMSG).The air-gap and permanent magnet size can be approximately determined based on our mathematics model,which is the most important part of SPMSM design.From our method,we can know that motor’s power out torque is related to the torque angle that we selected in our design and it affects the air-gap and permanent magnet size.If we choose a low torque angle,the motor or generator’s overload power handing capability will increase.The embrace value has a vital place in designing a motor or generator due to its effects on air gap flux density,cogging torque,efficiency and so on.In order to avoid the knee effect,the working point of the permanent magnet we selected in the design should be bigger than 0.5.The developed 36 slots,4 poles,surface mound permanent generator is proposed.The corresponding finite element analysis(FEA)model is built based on our design method.Structure optimization includes stator and rotor structure size,permanent magnet size,magnetic bridge and air gap length which are analyzed and simulated by ANSYS Maxwell 2D FEA.Thermal analysis is conducted,and the housing of the alternator is designed.The alternator prototype is fabricated and tested based on our design.
基金Project (60835004) supported by the National Natural Science Foundation of China
文摘A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.
基金Supported by National Natural Science Foundation of China(U1361109,51777060)Natural Science Foundation of Henan province(162300410117).
文摘The surface-mounted and interior permanent magnet synchronous motor(SIPMSM)has the characteristics of multiple variables,strong coupling and nonlinearity.In order to improve the performance of SIPMSM,this paper presents a multi-objective optimal design process using Taguchi and response surface methodology(RSM).The peak value of cogging torque(PVCT),ratio value of average torque and permanent magnet weight(RTW),torque ripple and back-EMF total harmonics distortion(ETHD)are selected as optimization goals.The experiment matrix is established by Taguchi method,and analyzed the tendency and proportion of the effect of the optimization parameters on SIPMSM performance.The rules of choosing multi-objective optimization parameters are obtained.The least-squares method is used to establish the optimal objective function,and RSM is used to obtain the resolutions of the optimization objective function.Comparing the initial performance with optimized performance verifies the effectiveness of the proposed method.
基金supported by the Industrial Strategic Technology Development Program(10070171,Development of core technology for advanced locomotion/manipulation based on high-speed/power robot platform and robot intelligence)funded By the Ministry of Trade,Industry&Energy(MI,Korea).
文摘In this paper,a design is presented for a high-speed,high-power motor for a four-legged robot actuator that was optimized using the weighted sum method(WSM)based on the Taguchi method,and the response surface method(RSM).First,output torque,torque constant,torque ripple,and efficiency were selected as objective functions for the optimized design.The sampling method was implemented to use a mixed orthogonal array and the single response characteristics of each objective function were compared using the Taguchi method.Moreover,to consider the multi-response characteristic of the objective functions,WSM was applied.Second,the 2D finite element analysis result of the RSM was compared with that using the WSM.Finally,an experiment was carried out on the manufactured motor and the optimized model is presented here.
基金Project supported by the National Natural Science Foundation of China（Nos.51207029 and 51507039） the Fundamental Research Funds for the Central Universities,China（No.HIT.NSRIF.2017013） the China Postdoctoral Science Foundation（No.2016M591529）
文摘A novel nonlinear model for surface permanent magnet synchronous motors（SPMSMs） is adopted to estimate the initial rotor position for hybrid electric vehicles（HEVs）. Usually, the accuracy of initial rotor position estimation for SPMSMs relies on magnetic saturation. To verify the saturation effect, the transient finite element analysis（FEA） model is presented first. Hybrid injection of a static voltage vector（SVV） superimposed with a high-frequency rotating voltage is proposed. The magnetic polarity is roughly identified with the aid of the saturation evaluation function, based on which an estimation of the position is performed. During this procedure, a special demodulation is suggested to extract signals of iron core saturation and rotor position. A Simulink/MATLAB platform for SPMSMs at standstill is constituted, and the effectiveness of the proposed strategy is verified. The proposed method is also validated by experimental results of an SPMSM drive.
