The simulation of salinity at different locations of a tidal river using physically-based hydrodynamic models is quite cumbersome because it requires many types of data, such as hydrological and hydraulic time series ...The simulation of salinity at different locations of a tidal river using physically-based hydrodynamic models is quite cumbersome because it requires many types of data, such as hydrological and hydraulic time series at boundaries, river geometry, and adjusted coefficients. Therefore, an artificial neural network (ANN) technique using a back-propagation neural network (BPNN) and a radial basis function neural network (RBFNN) is adopted as an effective alternative in salinity simulation studies. The present study focuses on comparing the performance of BPNN, RBFNN, and three-dimensional hydrodynamic models as applied to a tidal estuarine system. The observed salinity data sets collected from 18 to 22 May, 16 to 22 October, and 26 to 30 October 2002 (totaling 4320 data points) were used for BPNN and RBFNN model training and for hydrodynamic model calibration. The data sets collected from 30 May to 2 June and 11 to 15 November 2002 (totaling 2592 data points) were adopted for BPNN and RBFNN model verification and for hydrodynamic model verification. The results revealed that the ANN (BPNN and RBFNN) models were capable of predicting the nonlinear time series behavior of salinity to the multiple forcing signals of water stages at different stations and freshwater input at upstream boundaries. The salinity predicted by the ANN models was better than that predicted by the physically based hydrodynamic model. This study suggests that BPNN and RBFNN models are easy-to-use modeling tools for simulating the salinity variation in a tidal estuarine system.展开更多
Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade compone...Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.展开更多
Despite its utility in identifying patterns in celestial objects, the Hertzsprung-Russell diagram is not supported in dim or small stars;it struggles to provide insights into certain celestial objects such as brown dw...Despite its utility in identifying patterns in celestial objects, the Hertzsprung-Russell diagram is not supported in dim or small stars;it struggles to provide insights into certain celestial objects such as brown dwarfs [1]. The purpose of this experiment is to create an improved version of the diagram with a three-dimensional model that includes a third z-axis to accurately predict and chart the life cycles of all stars regardless of size. The values of the stars’ absolute magnitude and color indices were used to chart the surface gravity and metallicity, variables that were chosen due to their ease of collection and their likeliness to be within the range of values being assessed. To obtain the values for the model, data points from the database GAIA DR2 were utilized via the TAP protocol to query the SQL database. The data was transferred into a local CSV file to facilitate data manipulation. The data could be read and interpreted, as dim stars would likely have higher values of these variables, making it easier to include them in the diagram. The Pandas DataFrames tool on Python 3 was used to organize and manage the data efficiently. Matplotlib Graphs visualized the relationships between different stellar attributes by developing a linear regression line and an algorithm and creating scatter plots and sky maps to explore trends, hence designing three-dimensional diagrams. It was determined that the surface gravity diagram had a higher efficacy than metallicity due to their standard deviations of 0.4641441715272741 and 0.786577627976148, respectively.展开更多
Hypoxia is a typical feature of the tumor microenvironment,one of the most critical factors affecting cell behavior and tumor progression.However,the lack of tumor models able to precisely emulate natural brain tumor ...Hypoxia is a typical feature of the tumor microenvironment,one of the most critical factors affecting cell behavior and tumor progression.However,the lack of tumor models able to precisely emulate natural brain tumor tissue has impeded the study of the effects of hypoxia on the progression and growth of tumor cells.This study reports a three-dimensional(3D)brain tumor model obtained by encapsulating U87MG(U87)cells in a hydrogel containing type I collagen.It also documents the effect of various oxygen concentrations(1%,7%,and 21%)in the culture environment on U87 cell morphology,proliferation,viability,cell cycle,apoptosis rate,and migration.Finally,it compares two-dimensional(2D)and 3D cultures.For comparison purposes,cells cultured in flat culture dishes were used as the control(2D model).Cells cultured in the 3D model proliferated more slowly but had a higher apoptosis rate and proportion of cells in the resting phase(G0 phase)/gap I phase(G1 phase)than those cultured in the 2D model.Besides,the two models yielded significantly different cell morphologies.Finally,hypoxia(e.g.,1%O2)affected cell morphology,slowed cell growth,reduced cell viability,and increased the apoptosis rate in the 3D model.These results indicate that the constructed 3D model is effective for investigating the effects of biological and chemical factors on cell morphology and function,and can be more representative of the tumor microenvironment than 2D culture systems.The developed 3D glioblastoma tumor model is equally applicable to other studies in pharmacology and pathology.展开更多
Objective:This study aimed to explore the applications of three-dimensional (3D) technology, including virtual reality, augmented reality (AR), and 3D printing system, in the field of medicine, particularly in renal i...Objective:This study aimed to explore the applications of three-dimensional (3D) technology, including virtual reality, augmented reality (AR), and 3D printing system, in the field of medicine, particularly in renal interventions for cancer treatment.Methods:A specialized software transforms 2D medical images into precise 3D digital models, facilitating improved anatomical understanding and surgical planning. Patient-specific 3D printed anatomical models are utilized for preoperative planning, intraoperative guidance, and surgical education. AR technology enables the overlay of digital perceptions onto real-world surgical environments.Results:Patient-specific 3D printed anatomical models have multiple applications, such as preoperative planning, intraoperative guidance, trainee education, and patient counseling. Virtual reality involves substituting the real world with a computer-generated 3D environment, while AR overlays digitally created perceptions onto the existing reality. The advances in 3D modeling technology have sparked considerable interest in their application to partial nephrectomy in the realm of renal cancer. 3D printing, also known as additive manufacturing, constructs 3D objects based on computer-aided design or digital 3D models. Utilizing 3D-printed preoperative renal models provides benefits for surgical planning, offering a more reliable assessment of the tumor's relationship with vital anatomical structures and enabling better preparation for procedures. AR technology allows surgeons to visualize patient-specific renal anatomical structures and their spatial relationships with surrounding organs by projecting CT/MRI images onto a live laparoscopic video. Incorporating patient-specific 3D digital models into healthcare enhances best practice, resulting in improved patient care, increased patient satisfaction, and cost saving for the healthcare system.展开更多
Natural convection is a heat transfer mechanism driven by temperature or density differences,leading to fluid motion without external influence.It occurs in various natural and engineering phenomena,influencing heat t...Natural convection is a heat transfer mechanism driven by temperature or density differences,leading to fluid motion without external influence.It occurs in various natural and engineering phenomena,influencing heat transfer,climate,and fluid mixing in industrial processes.This work aims to use the Updated Lagrangian Particle Hydrodynamics(ULPH)theory to address natural convection problems.The Navier-Stokes equation is discretized using second-order nonlocal differential operators,allowing a direct solution of the Laplace operator for temperature in the energy equation.Various numerical simulations,including cases such as natural convection in square cavities and two concentric cylinders,were conducted to validate the reliability of the model.The results demonstrate that the proposed model exhibits excellent accuracy and performance,providing a promising and effective numerical approach for natural convection problems.展开更多
With drilling and seismic data of Transtensional(strike-slip)Fault System in the Ziyang area of the central Sichuan Basin,SW China plane-section integrated structural interpretation,3-D fault framework model building,...With drilling and seismic data of Transtensional(strike-slip)Fault System in the Ziyang area of the central Sichuan Basin,SW China plane-section integrated structural interpretation,3-D fault framework model building,fault throw analyzing,and balanced profile restoration,it is pointed out that the transtensional fault system in the Ziyang 3-D seismic survey consists of the northeast-trending F_(I)19 and F_(I)20 fault zones dominated by extensional deformation,as well as 3 sets of northwest-trending en echelon normal faults experienced dextral shear deformation.Among them,the F_(I)19 and F_(I)20 fault zones cut through the Neoproterozoic to Lower Triassic Jialingjiang Formation,presenting a 3-D structure of an“S”-shaped ribbon.And before Permian and during the Early Triassic,the F_(I)19 and F_(I)20 fault zones underwent at least two periods of structural superimposition.Besides,the 3 sets of northwest-trending en echelon normal faults are composed of small normal faults arranged in pairs,with opposite dip directions and partially left-stepped arrangement.And before Permian,they had formed almost,restricting the eastward growth and propagation of the F_(I)19 fault zone.The F_(I)19 and F_(I)20 fault zones communicate multiple sets of source rocks and reservoirs from deep to shallow,and the timing of fault activity matches well with oil and gas generation peaks.If there were favorable Cambrian-Triassic sedimentary facies and reservoirs developing on the local anticlinal belts of both sides of the F_(I)19 and F_(I)20 fault zones,the major reservoirs in this area are expected to achieve breakthroughs in oil and gas exploration.展开更多
Objective:To highlight the role of hyper accuracy three-dimensional(3D)reconstruction in facilitating surgical planning and guiding selective clamping during robot-assisted partial nephrectomy(RAPN).Methods:A transper...Objective:To highlight the role of hyper accuracy three-dimensional(3D)reconstruction in facilitating surgical planning and guiding selective clamping during robot-assisted partial nephrectomy(RAPN).Methods:A transperitoneal RAPN was performed in a 62-year-old male patient presenting with a 4 cm right anterior interpolar renal mass(R.E.N.A.L nephrometry score 7A).An abnormal vasculature was observed,with a single renal vein and two right renal arteries originating superiorly to the vein and anterior,when dividing in their segmental branches.According to the hyper accuracy 3D(HA3D^(®))rainbow model(MEDICS Srl,Turin,Italy),one branch belonging to one of the segmental arteries was feeding the tumor.This allowed for an accurate prediction of the area vascularized by each arterial branch.The 3D model was included in the intraoperative console view during the whole procedure,using the TilePro feature.A step-by-step explanation of the procedure is provided in the video attached to the present article.Results:The operative time was 90 min with a warm ischemia time on selective clamping of 13 min.Estimated blood loss was 180 mL.No intraoperative complication was encountered and no drain was placed at the end of the procedure.The patient was discharged on postoperative Day 2,without any early postoperative complications.The final pathology report showed a pathological tumor stage 1 clear cell renal cell carcinoma with negative surgical margins.Conclusion:The present study and the attached video illustrate the value of 3D rainbow model during the planning and execution of a RAPN with selective clamping.It shows how the surgeon can rely on this model to be more efficient by avoiding unnecessary surgical steps,and to safely adopt a“selective”clamping strategy that can translate in minimal functional impact.展开更多
Artificial fish reef is a kind of artificial structure in water,which provides a necessary and safe place for aquatic life such as fish to inhabit,grow,and breed,and creates an environment suitable for fish growth,so ...Artificial fish reef is a kind of artificial structure in water,which provides a necessary and safe place for aquatic life such as fish to inhabit,grow,and breed,and creates an environment suitable for fish growth,so as to protect and multiply fishery resources.In a large time scale,the physical process of sea area can deeply affect the chemical process and biological process,so the structure characteristics of artificial reef are the key factors affecting the flow field effect around the reef.In this study,through the hydrodynamic experiments of four kinds of reef models,including big windows box reef,big and small windows box reef,"(卐)"shaped reef and double-layer shellfish breeding reef,the influence of single reef structure on the flow field effect is analyzed,and the force conditions of different reefs under the same incoming current velocity are obtained.According to the simulation results,the safety research and calculation of five kinds of reef models are carried out,and the volumes of vortex area and upwelling area behind four kinds of reef are obtained.Using hydrodynamic model to simulate the flow field effect of reef area,optimizing the reef structure design,improving the maximum biological trapping and proliferation effect of reef,can provide theoretical guidance and scientific and technological support for the construction of reef area.展开更多
To address the problem that the display effect of hydrologic test data was not intuitive,the three-dimensional modeling technology of a hydrologic test reach based on GIS technology was proposed.The reach of of the Ye...To address the problem that the display effect of hydrologic test data was not intuitive,the three-dimensional modeling technology of a hydrologic test reach based on GIS technology was proposed.The reach of of the Yellow River around Lanzhou hydrological station was selected to study three-dimensional modeling.The elevation data of river was processed through three-dimensional model constructing,water surface modeling and three-dimensional animation demonstration by using ArcGIS Pro software.Based on the historical highest flood level data of the test reach on September 15,1981,the real scene restoration was carried out based on the three-dimensional model,and the hydrological factors such as water depth and channel storage were analyzed.The three-dimensional modeling based on GIS technology can directly and realistically reflect the changes of topography and water surface of the test reach,and improve the application of hydrologic test results in flood control.展开更多
In order to facilitate engineering design and coastal flooding protection, the potential storm surge induced by a typhoon is studied.Using an unstructured mesh, a coupled model which combines the advanced circulation ...In order to facilitate engineering design and coastal flooding protection, the potential storm surge induced by a typhoon is studied.Using an unstructured mesh, a coupled model which combines the advanced circulation （ ADCIRC ） hydrodynamic model and simulating waves nearshore （ SWAN ） model is applied to analyze the storm surge and waves on the coast of Jiangsu Province.The verifications of wind velocity, tidal levels and wave height show that this coupling model performs well to reflect the characteristics of the water levels and waves in the studied region.Results show that the effect of radiation stress on storm surge is significant, especially in shallow areas such as the coast of Jiangsu Province and the Yangtze estuary.By running the coupled model, the simulated potential flooding results can be employed in coastal engineering applications in the Jiangsu coastal area, such as storm surge warnings and extreme water level predictions.展开更多
Integrating wave energy converters(WECs)with offshore platforms offers numerous advantages,such as reducing wave loads,supplying energy to the platform,and cost-sharing in construction.This paper reports an experiment...Integrating wave energy converters(WECs)with offshore platforms offers numerous advantages,such as reducing wave loads,supplying energy to the platform,and cost-sharing in construction.This paper reports an experimental investigation focusing on the hydrodynamic characteristics of a proposed modular floating structure system integrated with WEC-type floating artificial reefs.The proposed system comprises several serially arranged hexagonal floating structures,anchored by tension legs,and integrated with outermost WEC-type floating artificial reefs.A simplified wave energy converter utilizing the relative pitch motion between adjacent modules for energy conversion was constructed in the scale model test.The effects of chain-type modular expansion on the multi-body motion response,mooring tension response,and WEC performance of the system have been thoroughly investigated.The experimental results indicate that increasing the number of hexagonal modules can notably reduce the system’s surge response,particularly under survival sea conditions.The connection of the outermost reef modules slightly increases the tension leg load of the adjacent module,whereas the tension leg load remains relatively consistent across the inner hexagonal modules.Furthermore,through a comparison of the dynamic responses of the hexagonal module connected and unconnected outermost reefs,the good performance in terms of energy conversion and wave attenuation of the WECtype floating artificial reef modules was effectively validated.The main results from this work can provide useful references for engineering applications involving modular floating structures integrated with WECs.展开更多
This paper presents the features of newly designed hydrodynamics test for the scaled model of 4500 m deepsea open-framed remotely operated vehicle （ROV）, which is being researched and developed by Shanghai Jiao Tong...This paper presents the features of newly designed hydrodynamics test for the scaled model of 4500 m deepsea open-framed remotely operated vehicle （ROV）, which is being researched and developed by Shanghai Jiao Tong University. Accurate hydrodynamics coefficients measurement and spatial modeling of ROV are significant for the maneuverability and control algorithm. The scaled model of ROV was constructed by 1：1.6. Hydrodynamics coefficients were measured through VPMM and LAHPMM towing test. And dynamics model was derived as a set of equations, describing nonlinear and coupled 5-DOF spatial motions. Rotation control motion was simulated to verify spatial model proposed. Research and application of hydrodynamics coefficients are expected to enable ROV to overcome uncertainty and disturbances of deepsea environment, and accomplish some more challengeable and practical missions.展开更多
With the acceleration of marine construction in China,the exploitation and utilization of resources from islands and reefs are necessary.To prevent and dissipate waves in the process of resource exploitation and utili...With the acceleration of marine construction in China,the exploitation and utilization of resources from islands and reefs are necessary.To prevent and dissipate waves in the process of resource exploitation and utilization,a more effective method is to install floating breakwaters near the terrain of islands and reefs.The terrain around islands and reefs is complex,and waves undergo a series of changes due to the impact of the complex terrain in transmission.It is important to find a suitable location for floating breakwater systems on islands and reefs and investigate how the terrain affects the system’s hydrodynamic performance.This paper introduces a three-cylinder floating breakwater design.The breakwater system consists of 8 units connected by elastic structures and secured by a slack mooring system.To evaluate its effectiveness,a 3D model experiment was conducted in a wave basin.During the experiment,a model resembling the islands and reefs terrain was created on the basis of the water depth map of a specific region in the East China Sea.The transmission coefficients and motion responses of the three-cylinder floating breakwater system were then measured.This was done both in the middle of and behind the islands and reefs terrain.According to the experimental results,the three-cylinder floating breakwater system performs better in terms of hydrodynamics when it is placed behind the terrain of islands and reefs than in the middle of the same terrain.展开更多
This paper presents a hybrid model for three-dimensional Geographical Information Systems which is an integration of surface- and volume-based models. The Triangulated Irregular Network (TIN) and octree models are int...This paper presents a hybrid model for three-dimensional Geographical Information Systems which is an integration of surface- and volume-based models. The Triangulated Irregular Network (TIN) and octree models are integrated in this hybrid models. The TIN model works as a surface-based model which mainly serves for surface presentation and visualization. On the other hand, the octree encoding supports volumetric analysis. The designed data structure brings a major advantage in the three-dimensional selective retrieval. This technique increases the efficiency of three-dimensional data operation.展开更多
The hydrodynamic forces and flow field of artificial reef models in steady flow were numerically investigated using the RNG κ-ε turbulent model. The numerical simulation results are consistent with results observed ...The hydrodynamic forces and flow field of artificial reef models in steady flow were numerically investigated using the RNG κ-ε turbulent model. The numerical simulation results are consistent with results observed by experimental means. A comparative study indicates that the corresponding errors of forces between calculated values and values observed in the experiment vary in the range of2.3%-11.2% and that the corresponding errors of velocities vary in the range of 1.3%-15.8%. The flow field numerical results show that upstream and vortices exist when the current passes over and through the surface of the reef model. This study suggests that the numerical simulation method can be applied to predict the forces and flow field associated with artificial reefs.展开更多
A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal d...A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal direction and z-level grid in the vertical direction. The three-dimensional model is discretized by the semi-implicit finite-volume method, in that the free-surface and the vertical diffusion are semi-implicit, thereby removing stability limitations associated with the surface gravity wave and vertical diffusion terms. The remaining terms in the momentum equations are discretized explicitly by an integral method. The partial cell method is used for resolving topography, which enables the model to better represent irregular topography. The model has been tested against analytical cases for wind and tidal oscillation circulation, and is applied to simulating the tidal flow in the Bohal Sea. The results are in good agreement both with the analytical solutions and measurement results.展开更多
Merits of the Fernandes model(Fernandes et al.1983)for two-phase slug flow in verticaltubes are reviewed in this paper.While predicting many macroscopic parameters of slug flow in verti-cal tubes,it fails to present c...Merits of the Fernandes model(Fernandes et al.1983)for two-phase slug flow in verticaltubes are reviewed in this paper.While predicting many macroscopic parameters of slug flow in verti-cal tubes,it fails to present correctly the trend that the average voidage in liquid slugs increases asthe rising velocity of Taylor bubbles is increased.It is also desirable to extend its application toelectrolyte systems, and to churn flow conditions.Based on the diagnostic analysis,the model equa-tion for gas entrainment by falling liquid film is reformulated and the influence of surface tension isalso accounted for.Development of the falling liquid film is recognized in the revised model in or-der to suit the case of short Taylor bubbles as well.The modified model predicts the variation of av-erage voidage in liquid slugs in good agreement with available experimental data.展开更多
Radius of ceramic cone can largely contribute into final solution of analytic models of penetration into ceramic/metal targets.In the present research,a modified model based on radius of ceramic cone was presented for...Radius of ceramic cone can largely contribute into final solution of analytic models of penetration into ceramic/metal targets.In the present research,a modified model based on radius of ceramic cone was presented for ceramic/aluminum targets.In order to investigate and evaluate accuracy of the presented analytic model,obtained results were compared against the results of the Florence’s analytic model and also against numerical modeling results.The phenomenon of impact onto ceramic/aluminum composites were modeled using smoothed particle hydrodynamics(SPH)implemented utilizing ABAQUS Software.Results indicated that,with increasing initial velocity and ceramic thickness and decreasing support layer thickness,the radius of ceramic cone decreases;this ends up increasing residual velocity of the projectile and penetration time and extending the area across which the pressure is distributed.These findings indicate enhanced levels of target energy absorption and the required energy for bending and tensioning the target.As such,it can be observed that,at the same thickness and areal density,the ceramic target has its efficiency enhanced with increasing ceramic thickness and decreasing the support layer thickness.Finally,the results revealed that the associated data with SPH confirm the modified analytic model at higher accuracy than the Florence’s analytic model.展开更多
A test rig is built to model the dynamic response of submarine pipelines with an underwater shaking table in the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, China. Model ...A test rig is built to model the dynamic response of submarine pipelines with an underwater shaking table in the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, China. Model tests are carried out to consider the effects of exciting wave directions and types. Based on the experimental results, two hydrodynamic force models derived from Morisen equation and Wake model are presented respectively. By use of hydrodynamic force models suitable for free spanning submarine pipelines under earthquakes, diseretized equations of motion are obtained and finite element models are established to analyze dynamic response of free spanning submarine pipeline subjected to multi-support seismic excitations. The comparison of numerical results with experimental results shows that the improved Morison and Wake hydrodynamic force models could satisfactorily predict dynamic response on the free spanning submarine pipelines subjected to earthquakes.展开更多
文摘The simulation of salinity at different locations of a tidal river using physically-based hydrodynamic models is quite cumbersome because it requires many types of data, such as hydrological and hydraulic time series at boundaries, river geometry, and adjusted coefficients. Therefore, an artificial neural network (ANN) technique using a back-propagation neural network (BPNN) and a radial basis function neural network (RBFNN) is adopted as an effective alternative in salinity simulation studies. The present study focuses on comparing the performance of BPNN, RBFNN, and three-dimensional hydrodynamic models as applied to a tidal estuarine system. The observed salinity data sets collected from 18 to 22 May, 16 to 22 October, and 26 to 30 October 2002 (totaling 4320 data points) were used for BPNN and RBFNN model training and for hydrodynamic model calibration. The data sets collected from 30 May to 2 June and 11 to 15 November 2002 (totaling 2592 data points) were adopted for BPNN and RBFNN model verification and for hydrodynamic model verification. The results revealed that the ANN (BPNN and RBFNN) models were capable of predicting the nonlinear time series behavior of salinity to the multiple forcing signals of water stages at different stations and freshwater input at upstream boundaries. The salinity predicted by the ANN models was better than that predicted by the physically based hydrodynamic model. This study suggests that BPNN and RBFNN models are easy-to-use modeling tools for simulating the salinity variation in a tidal estuarine system.
基金Project supported by the National Natural Science Foundation of China(Nos.12372071 and 12372070)the Aeronautical Science Fund of China(No.2022Z055052001)the Foundation of China Scholarship Council(No.202306830079)。
文摘Currently,there are a limited number of dynamic models available for braided composite plates with large overall motions,despite the incorporation of three-dimensional(3D)braided composites into rotating blade components.In this paper,a dynamic model of 3D 4-directional braided composite thin plates considering braiding directions is established.Based on Kirchhoff's plate assumptions,the displacement variables of the plate are expressed.By incorporating the braiding directions into the constitutive equation of the braided composites,the dynamic model of the plate considering braiding directions is obtained.The effects of the speeds,braiding directions,and braided angles on the responses of the plate with fixed-axis rotation and translational motion,respectively,are investigated.This paper presents a dynamic theory for calculating the deformation of 3D braided composite structures undergoing both translational and rotational motions.It also provides a simulation method for investigating the dynamic behavior of non-isotropic material plates in various applications.
文摘Despite its utility in identifying patterns in celestial objects, the Hertzsprung-Russell diagram is not supported in dim or small stars;it struggles to provide insights into certain celestial objects such as brown dwarfs [1]. The purpose of this experiment is to create an improved version of the diagram with a three-dimensional model that includes a third z-axis to accurately predict and chart the life cycles of all stars regardless of size. The values of the stars’ absolute magnitude and color indices were used to chart the surface gravity and metallicity, variables that were chosen due to their ease of collection and their likeliness to be within the range of values being assessed. To obtain the values for the model, data points from the database GAIA DR2 were utilized via the TAP protocol to query the SQL database. The data was transferred into a local CSV file to facilitate data manipulation. The data could be read and interpreted, as dim stars would likely have higher values of these variables, making it easier to include them in the diagram. The Pandas DataFrames tool on Python 3 was used to organize and manage the data efficiently. Matplotlib Graphs visualized the relationships between different stellar attributes by developing a linear regression line and an algorithm and creating scatter plots and sky maps to explore trends, hence designing three-dimensional diagrams. It was determined that the surface gravity diagram had a higher efficacy than metallicity due to their standard deviations of 0.4641441715272741 and 0.786577627976148, respectively.
基金supported by the National Natural Science Foundation of China (No. 52275291)the Fundamental Research Funds for the Central Universitiesthe Program for Innovation Team of Shaanxi Province,China (No. 2023-CX-TD-17)
文摘Hypoxia is a typical feature of the tumor microenvironment,one of the most critical factors affecting cell behavior and tumor progression.However,the lack of tumor models able to precisely emulate natural brain tumor tissue has impeded the study of the effects of hypoxia on the progression and growth of tumor cells.This study reports a three-dimensional(3D)brain tumor model obtained by encapsulating U87MG(U87)cells in a hydrogel containing type I collagen.It also documents the effect of various oxygen concentrations(1%,7%,and 21%)in the culture environment on U87 cell morphology,proliferation,viability,cell cycle,apoptosis rate,and migration.Finally,it compares two-dimensional(2D)and 3D cultures.For comparison purposes,cells cultured in flat culture dishes were used as the control(2D model).Cells cultured in the 3D model proliferated more slowly but had a higher apoptosis rate and proportion of cells in the resting phase(G0 phase)/gap I phase(G1 phase)than those cultured in the 2D model.Besides,the two models yielded significantly different cell morphologies.Finally,hypoxia(e.g.,1%O2)affected cell morphology,slowed cell growth,reduced cell viability,and increased the apoptosis rate in the 3D model.These results indicate that the constructed 3D model is effective for investigating the effects of biological and chemical factors on cell morphology and function,and can be more representative of the tumor microenvironment than 2D culture systems.The developed 3D glioblastoma tumor model is equally applicable to other studies in pharmacology and pathology.
文摘Objective:This study aimed to explore the applications of three-dimensional (3D) technology, including virtual reality, augmented reality (AR), and 3D printing system, in the field of medicine, particularly in renal interventions for cancer treatment.Methods:A specialized software transforms 2D medical images into precise 3D digital models, facilitating improved anatomical understanding and surgical planning. Patient-specific 3D printed anatomical models are utilized for preoperative planning, intraoperative guidance, and surgical education. AR technology enables the overlay of digital perceptions onto real-world surgical environments.Results:Patient-specific 3D printed anatomical models have multiple applications, such as preoperative planning, intraoperative guidance, trainee education, and patient counseling. Virtual reality involves substituting the real world with a computer-generated 3D environment, while AR overlays digitally created perceptions onto the existing reality. The advances in 3D modeling technology have sparked considerable interest in their application to partial nephrectomy in the realm of renal cancer. 3D printing, also known as additive manufacturing, constructs 3D objects based on computer-aided design or digital 3D models. Utilizing 3D-printed preoperative renal models provides benefits for surgical planning, offering a more reliable assessment of the tumor's relationship with vital anatomical structures and enabling better preparation for procedures. AR technology allows surgeons to visualize patient-specific renal anatomical structures and their spatial relationships with surrounding organs by projecting CT/MRI images onto a live laparoscopic video. Incorporating patient-specific 3D digital models into healthcare enhances best practice, resulting in improved patient care, increased patient satisfaction, and cost saving for the healthcare system.
基金support from the National Natural Science Foundations of China(Nos.11972267 and 11802214)the Open Foundation of the Hubei Key Laboratory of Theory and Application of Advanced Materials Mechanics and the Open Foundation of Hubei Key Laboratory of Engineering Structural Analysis and Safety Assessment.
文摘Natural convection is a heat transfer mechanism driven by temperature or density differences,leading to fluid motion without external influence.It occurs in various natural and engineering phenomena,influencing heat transfer,climate,and fluid mixing in industrial processes.This work aims to use the Updated Lagrangian Particle Hydrodynamics(ULPH)theory to address natural convection problems.The Navier-Stokes equation is discretized using second-order nonlocal differential operators,allowing a direct solution of the Laplace operator for temperature in the energy equation.Various numerical simulations,including cases such as natural convection in square cavities and two concentric cylinders,were conducted to validate the reliability of the model.The results demonstrate that the proposed model exhibits excellent accuracy and performance,providing a promising and effective numerical approach for natural convection problems.
基金Supported by the Key Project of National Natural Science Foundation of China(42330810).
文摘With drilling and seismic data of Transtensional(strike-slip)Fault System in the Ziyang area of the central Sichuan Basin,SW China plane-section integrated structural interpretation,3-D fault framework model building,fault throw analyzing,and balanced profile restoration,it is pointed out that the transtensional fault system in the Ziyang 3-D seismic survey consists of the northeast-trending F_(I)19 and F_(I)20 fault zones dominated by extensional deformation,as well as 3 sets of northwest-trending en echelon normal faults experienced dextral shear deformation.Among them,the F_(I)19 and F_(I)20 fault zones cut through the Neoproterozoic to Lower Triassic Jialingjiang Formation,presenting a 3-D structure of an“S”-shaped ribbon.And before Permian and during the Early Triassic,the F_(I)19 and F_(I)20 fault zones underwent at least two periods of structural superimposition.Besides,the 3 sets of northwest-trending en echelon normal faults are composed of small normal faults arranged in pairs,with opposite dip directions and partially left-stepped arrangement.And before Permian,they had formed almost,restricting the eastward growth and propagation of the F_(I)19 fault zone.The F_(I)19 and F_(I)20 fault zones communicate multiple sets of source rocks and reservoirs from deep to shallow,and the timing of fault activity matches well with oil and gas generation peaks.If there were favorable Cambrian-Triassic sedimentary facies and reservoirs developing on the local anticlinal belts of both sides of the F_(I)19 and F_(I)20 fault zones,the major reservoirs in this area are expected to achieve breakthroughs in oil and gas exploration.
文摘Objective:To highlight the role of hyper accuracy three-dimensional(3D)reconstruction in facilitating surgical planning and guiding selective clamping during robot-assisted partial nephrectomy(RAPN).Methods:A transperitoneal RAPN was performed in a 62-year-old male patient presenting with a 4 cm right anterior interpolar renal mass(R.E.N.A.L nephrometry score 7A).An abnormal vasculature was observed,with a single renal vein and two right renal arteries originating superiorly to the vein and anterior,when dividing in their segmental branches.According to the hyper accuracy 3D(HA3D^(®))rainbow model(MEDICS Srl,Turin,Italy),one branch belonging to one of the segmental arteries was feeding the tumor.This allowed for an accurate prediction of the area vascularized by each arterial branch.The 3D model was included in the intraoperative console view during the whole procedure,using the TilePro feature.A step-by-step explanation of the procedure is provided in the video attached to the present article.Results:The operative time was 90 min with a warm ischemia time on selective clamping of 13 min.Estimated blood loss was 180 mL.No intraoperative complication was encountered and no drain was placed at the end of the procedure.The patient was discharged on postoperative Day 2,without any early postoperative complications.The final pathology report showed a pathological tumor stage 1 clear cell renal cell carcinoma with negative surgical margins.Conclusion:The present study and the attached video illustrate the value of 3D rainbow model during the planning and execution of a RAPN with selective clamping.It shows how the surgeon can rely on this model to be more efficient by avoiding unnecessary surgical steps,and to safely adopt a“selective”clamping strategy that can translate in minimal functional impact.
基金supported by the National Key R&D Plan(No.2023YFD2401104)Tianjin Agricultural Development Service Center Science and Technology Innovation Project for Youth(No.ZXKJ202429 and No.ZXKJ202454).
文摘Artificial fish reef is a kind of artificial structure in water,which provides a necessary and safe place for aquatic life such as fish to inhabit,grow,and breed,and creates an environment suitable for fish growth,so as to protect and multiply fishery resources.In a large time scale,the physical process of sea area can deeply affect the chemical process and biological process,so the structure characteristics of artificial reef are the key factors affecting the flow field effect around the reef.In this study,through the hydrodynamic experiments of four kinds of reef models,including big windows box reef,big and small windows box reef,"(卐)"shaped reef and double-layer shellfish breeding reef,the influence of single reef structure on the flow field effect is analyzed,and the force conditions of different reefs under the same incoming current velocity are obtained.According to the simulation results,the safety research and calculation of five kinds of reef models are carried out,and the volumes of vortex area and upwelling area behind four kinds of reef are obtained.Using hydrodynamic model to simulate the flow field effect of reef area,optimizing the reef structure design,improving the maximum biological trapping and proliferation effect of reef,can provide theoretical guidance and scientific and technological support for the construction of reef area.
文摘To address the problem that the display effect of hydrologic test data was not intuitive,the three-dimensional modeling technology of a hydrologic test reach based on GIS technology was proposed.The reach of of the Yellow River around Lanzhou hydrological station was selected to study three-dimensional modeling.The elevation data of river was processed through three-dimensional model constructing,water surface modeling and three-dimensional animation demonstration by using ArcGIS Pro software.Based on the historical highest flood level data of the test reach on September 15,1981,the real scene restoration was carried out based on the three-dimensional model,and the hydrological factors such as water depth and channel storage were analyzed.The three-dimensional modeling based on GIS technology can directly and realistically reflect the changes of topography and water surface of the test reach,and improve the application of hydrologic test results in flood control.
基金The National Natural Science Foundation of China(No.51209040,51279134)the Natural Science Foundation of Jiangsu Province(No.BK2012341)+1 种基金the Fundamental Research Funds for the Central Universities(No.SJLX_0087)the Research Fund of Nanjing Hydraulic Research Institute(No.Y213012)
文摘In order to facilitate engineering design and coastal flooding protection, the potential storm surge induced by a typhoon is studied.Using an unstructured mesh, a coupled model which combines the advanced circulation （ ADCIRC ） hydrodynamic model and simulating waves nearshore （ SWAN ） model is applied to analyze the storm surge and waves on the coast of Jiangsu Province.The verifications of wind velocity, tidal levels and wave height show that this coupling model performs well to reflect the characteristics of the water levels and waves in the studied region.Results show that the effect of radiation stress on storm surge is significant, especially in shallow areas such as the coast of Jiangsu Province and the Yangtze estuary.By running the coupled model, the simulated potential flooding results can be employed in coastal engineering applications in the Jiangsu coastal area, such as storm surge warnings and extreme water level predictions.
基金financially supported by the National Natural Science Foundation of China(Grant No.52161041)the Natural Science Foundation of Hainan Province(Grant No.520RC552).
文摘Integrating wave energy converters(WECs)with offshore platforms offers numerous advantages,such as reducing wave loads,supplying energy to the platform,and cost-sharing in construction.This paper reports an experimental investigation focusing on the hydrodynamic characteristics of a proposed modular floating structure system integrated with WEC-type floating artificial reefs.The proposed system comprises several serially arranged hexagonal floating structures,anchored by tension legs,and integrated with outermost WEC-type floating artificial reefs.A simplified wave energy converter utilizing the relative pitch motion between adjacent modules for energy conversion was constructed in the scale model test.The effects of chain-type modular expansion on the multi-body motion response,mooring tension response,and WEC performance of the system have been thoroughly investigated.The experimental results indicate that increasing the number of hexagonal modules can notably reduce the system’s surge response,particularly under survival sea conditions.The connection of the outermost reef modules slightly increases the tension leg load of the adjacent module,whereas the tension leg load remains relatively consistent across the inner hexagonal modules.Furthermore,through a comparison of the dynamic responses of the hexagonal module connected and unconnected outermost reefs,the good performance in terms of energy conversion and wave attenuation of the WECtype floating artificial reef modules was effectively validated.The main results from this work can provide useful references for engineering applications involving modular floating structures integrated with WECs.
基金financially supported by the National High Technology Research and Development Program of China(863 Program,Grant No.2008AA092301)
文摘This paper presents the features of newly designed hydrodynamics test for the scaled model of 4500 m deepsea open-framed remotely operated vehicle （ROV）, which is being researched and developed by Shanghai Jiao Tong University. Accurate hydrodynamics coefficients measurement and spatial modeling of ROV are significant for the maneuverability and control algorithm. The scaled model of ROV was constructed by 1：1.6. Hydrodynamics coefficients were measured through VPMM and LAHPMM towing test. And dynamics model was derived as a set of equations, describing nonlinear and coupled 5-DOF spatial motions. Rotation control motion was simulated to verify spatial model proposed. Research and application of hydrodynamics coefficients are expected to enable ROV to overcome uncertainty and disturbances of deepsea environment, and accomplish some more challengeable and practical missions.
基金financially supported by the China National Funds for Distinguished Young Scientists(Grant No.52025112).
文摘With the acceleration of marine construction in China,the exploitation and utilization of resources from islands and reefs are necessary.To prevent and dissipate waves in the process of resource exploitation and utilization,a more effective method is to install floating breakwaters near the terrain of islands and reefs.The terrain around islands and reefs is complex,and waves undergo a series of changes due to the impact of the complex terrain in transmission.It is important to find a suitable location for floating breakwater systems on islands and reefs and investigate how the terrain affects the system’s hydrodynamic performance.This paper introduces a three-cylinder floating breakwater design.The breakwater system consists of 8 units connected by elastic structures and secured by a slack mooring system.To evaluate its effectiveness,a 3D model experiment was conducted in a wave basin.During the experiment,a model resembling the islands and reefs terrain was created on the basis of the water depth map of a specific region in the East China Sea.The transmission coefficients and motion responses of the three-cylinder floating breakwater system were then measured.This was done both in the middle of and behind the islands and reefs terrain.According to the experimental results,the three-cylinder floating breakwater system performs better in terms of hydrodynamics when it is placed behind the terrain of islands and reefs than in the middle of the same terrain.
文摘This paper presents a hybrid model for three-dimensional Geographical Information Systems which is an integration of surface- and volume-based models. The Triangulated Irregular Network (TIN) and octree models are integrated in this hybrid models. The TIN model works as a surface-based model which mainly serves for surface presentation and visualization. On the other hand, the octree encoding supports volumetric analysis. The designed data structure brings a major advantage in the three-dimensional selective retrieval. This technique increases the efficiency of three-dimensional data operation.
基金Supported by the National High Technology Research and Development Program of China(863 Programs)(No.2006AA100301)Science and Technology Development Program of Shandong Province(No.2005GG3205102)
文摘The hydrodynamic forces and flow field of artificial reef models in steady flow were numerically investigated using the RNG κ-ε turbulent model. The numerical simulation results are consistent with results observed by experimental means. A comparative study indicates that the corresponding errors of forces between calculated values and values observed in the experiment vary in the range of2.3%-11.2% and that the corresponding errors of velocities vary in the range of 1.3%-15.8%. The flow field numerical results show that upstream and vortices exist when the current passes over and through the surface of the reef model. This study suggests that the numerical simulation method can be applied to predict the forces and flow field associated with artificial reefs.
基金The Major State Basic Research Program of China under contract No. 2012CB417002the National Natural Science Foundation of China under contract Nos 50909065 and 51109039
文摘A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal direction and z-level grid in the vertical direction. The three-dimensional model is discretized by the semi-implicit finite-volume method, in that the free-surface and the vertical diffusion are semi-implicit, thereby removing stability limitations associated with the surface gravity wave and vertical diffusion terms. The remaining terms in the momentum equations are discretized explicitly by an integral method. The partial cell method is used for resolving topography, which enables the model to better represent irregular topography. The model has been tested against analytical cases for wind and tidal oscillation circulation, and is applied to simulating the tidal flow in the Bohal Sea. The results are in good agreement both with the analytical solutions and measurement results.
文摘Merits of the Fernandes model(Fernandes et al.1983)for two-phase slug flow in verticaltubes are reviewed in this paper.While predicting many macroscopic parameters of slug flow in verti-cal tubes,it fails to present correctly the trend that the average voidage in liquid slugs increases asthe rising velocity of Taylor bubbles is increased.It is also desirable to extend its application toelectrolyte systems, and to churn flow conditions.Based on the diagnostic analysis,the model equa-tion for gas entrainment by falling liquid film is reformulated and the influence of surface tension isalso accounted for.Development of the falling liquid film is recognized in the revised model in or-der to suit the case of short Taylor bubbles as well.The modified model predicts the variation of av-erage voidage in liquid slugs in good agreement with available experimental data.
文摘Radius of ceramic cone can largely contribute into final solution of analytic models of penetration into ceramic/metal targets.In the present research,a modified model based on radius of ceramic cone was presented for ceramic/aluminum targets.In order to investigate and evaluate accuracy of the presented analytic model,obtained results were compared against the results of the Florence’s analytic model and also against numerical modeling results.The phenomenon of impact onto ceramic/aluminum composites were modeled using smoothed particle hydrodynamics(SPH)implemented utilizing ABAQUS Software.Results indicated that,with increasing initial velocity and ceramic thickness and decreasing support layer thickness,the radius of ceramic cone decreases;this ends up increasing residual velocity of the projectile and penetration time and extending the area across which the pressure is distributed.These findings indicate enhanced levels of target energy absorption and the required energy for bending and tensioning the target.As such,it can be observed that,at the same thickness and areal density,the ceramic target has its efficiency enhanced with increasing ceramic thickness and decreasing the support layer thickness.Finally,the results revealed that the associated data with SPH confirm the modified analytic model at higher accuracy than the Florence’s analytic model.
基金supported jointly by the National Natural Science Foundation of China and Korea Scienceand Engineering Foundation(Grant No.50811140341)
文摘A test rig is built to model the dynamic response of submarine pipelines with an underwater shaking table in the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, China. Model tests are carried out to consider the effects of exciting wave directions and types. Based on the experimental results, two hydrodynamic force models derived from Morisen equation and Wake model are presented respectively. By use of hydrodynamic force models suitable for free spanning submarine pipelines under earthquakes, diseretized equations of motion are obtained and finite element models are established to analyze dynamic response of free spanning submarine pipeline subjected to multi-support seismic excitations. The comparison of numerical results with experimental results shows that the improved Morison and Wake hydrodynamic force models could satisfactorily predict dynamic response on the free spanning submarine pipelines subjected to earthquakes.
