The lattice parameter,measured with sufficient accuracy,can be utilized to evaluate the quality of single crystals and to determine the equation of state for materials.We propose an iterative method for obtaining more...The lattice parameter,measured with sufficient accuracy,can be utilized to evaluate the quality of single crystals and to determine the equation of state for materials.We propose an iterative method for obtaining more precise lattice parameters using the interaction points for the pseudo-Kossel pattern obtained from laser-induced X-ray diffraction(XRD).This method has been validated by the analysis of an XRD experiment conducted on iron single crystals.Furthermore,the method was used to calculate the compression ratio and rotated angle of an LiF sample under high pressure loading.This technique provides a robust tool for in-situ characterization of structural changes in single crystals under extreme conditions.It has significant implications for studying the equation of state and phase transitions.展开更多
A series of SnO2‐based catalysts modified by Mn, Zr, Ti and Pb oxides with a Sn/M （M=Mn, Zr, Ti and Pb） molar ratio of 9/1 were prepared by a co‐precipitation method and used for CH4 and CO oxidation. The Mn3＋, ...A series of SnO2‐based catalysts modified by Mn, Zr, Ti and Pb oxides with a Sn/M （M=Mn, Zr, Ti and Pb） molar ratio of 9/1 were prepared by a co‐precipitation method and used for CH4 and CO oxidation. The Mn3＋, Zr4＋, Ti4＋and Pb4＋cations are incorporated into the lattice of tetragonal rutile SnO2 to form a solid solution structure. As a consequence, the surface area and thermal stability of the catalysts are improved. Moreover, the oxygen species of the modified catalysts become easier to be reduced. Therefore, the oxidation activity over the catalysts was improved, except for the one modified by Pb oxide. Manganese oxide demonstrates the best promotional effects for SnO2. Using an X‐ray diffraction extrapolation method, the lattice capacity of SnO2 for Mn2O3 was 0.135 g Mn2O3/g SnO2, which indicates that to form stable solid solution, only 21%Sn4＋cations in the lattice can be maximally replaced by Mn3＋. If the amount of Mn3＋cations is over the capacity, Mn2O3 will be formed, which is not favorable for the activity of the catalysts. The Sn rich samples with only Sn‐Mn solid solution phase show higher activity than the ones with excess Mn2O3 species.展开更多
Twin roll cast ZK60 alloy strip/sheet with final thickness of 0.5 mm was prepared, and effect of rolling temperature on microstructure and texture development was investigated using OM and XRD technique, microstructur...Twin roll cast ZK60 alloy strip/sheet with final thickness of 0.5 mm was prepared, and effect of rolling temperature on microstructure and texture development was investigated using OM and XRD technique, microstructure and texture were measured on specimens subjected to rolling experiment at different rolling temperature, and macrotexture was also evaluated by X-ray diffraction method. In addition, the （1010）and （0002） pole figures were measured, and the tensile test was performed to reveal the influence of rolling temperature on mechanical properties. The results show that the microstrucmre of ZK60 alloy sheet consisted of fibrous structure with elongated grains, and shear bands along the rolling direction after warm rolling. Dynamic recrystallization could be found during the warm rolling process at rolling temperature 350℃ and above. And many fine recrystallized grain could be observed in the shear bands area. It is a little difficult to see the recrystallized grain in the sheet warm rolled at 300℃ because of higher density of shear bands. The warm rolled ZK60 alloy sheet exhibited strong （0002） pole texture, the intensity of （0002） pole figure decreases with the increasing of rolling temperature and the basal pole tilted slightly to the transverse direction after warm rolling.展开更多
In this work, BiV04 powders were synthesized by a sol-gel method, and the BiV04 gels with different calcination temperature were investigated by X-ray diffraction （XRD）. Absorption range and band gap energy, which a...In this work, BiV04 powders were synthesized by a sol-gel method, and the BiV04 gels with different calcination temperature were investigated by X-ray diffraction （XRD）. Absorption range and band gap energy, which are respon- sible for the observed photocatalyst behavior, were investigated by UV/vis diffuse reflectance spectroscopy （DRS） for pure and silver oxide loaded BiV04. Pbotocatalytic properties of the prepared samples were examined by studying the degradation of the methyl orange. When using NaCI02 as an electron acceptor, the possible photocatalytic mech- anism has been discussed by photocatalytic reactions. With the help of electron acceptor, the results show clearly that the BiV04 loaded silver oxide exhibited superior photocatalytic activity in simulated dye wastewater treatment.展开更多
Mesoporous CeO2 was first synthesized by hydrothermal method,and then used to synthesize different contents of CuO)x/CeO2(x:molar ratio of Cu to Ce) by deposition-precipitation method.These materials were characterize...Mesoporous CeO2 was first synthesized by hydrothermal method,and then used to synthesize different contents of CuO)x/CeO2(x:molar ratio of Cu to Ce) by deposition-precipitation method.These materials were characterized by X-ray diffraction(XRD),N2 adsorption and desorption,H2 temperature programmed reduction(H2-TPR) and O2 temperature programmed desorption(O2-TPD) to study the crystal structure,surface area,and the mechanism of CO oxidation.The results show that,on XRD patterns,no evidence of CuO diffraction peaks is present until Cu loading is increased to 20%.The BET surface area decreases noticeably with the increase of Cu content.Compared with other samples,the better reducibility and activity oxygen species of(CuO)10%/CeO2coincide with its better catalytic activity.展开更多
ZnO nanorods, with the c-axis orientation used for transparent conductors, solar cells, sensors especially the functionalized ZnO nanorods with some kinds of enzymes have been used for biosensor. In this work, we desc...ZnO nanorods, with the c-axis orientation used for transparent conductors, solar cells, sensors especially the functionalized ZnO nanorods with some kinds of enzymes have been used for biosensor. In this work, we describe the process immobilization of galactose oxidase on ZnO nanorods surface with glutaraldehyde as a cross-linker molecule to make the working electrode in electrochemical biosensor. ZnO nanorods were grown on FTO （Fluorine-doped tin oxide） substrate by solution method at low temperature. The crystalline phase and orientation of ZnO nanorods were identified using X-ray diffraction. The efficiency of the immobilization was calculated by Braford method showed that about 36% enzyme content was immobilized on ZnO nanorods surface. The working electrode based on the immobilized ZnO nanorods was tested in galactose solution by CV （cyclic voltammetry） method indicated the value of current intensity is about 0.14 μA. These results clearly demonstrate the potential of galactose sensor based on ZnO nanorod.展开更多
Based on analysis on X-ray diffraction, the metamorphic grade of coal in southeast Qinshui Basin was discussed, and a precise evaluation of coal rank through XRD analysis was made, in addition, the correlation of coal...Based on analysis on X-ray diffraction, the metamorphic grade of coal in southeast Qinshui Basin was discussed, and a precise evaluation of coal rank through XRD analysis was made, in addition, the correlation of coal rank and vitrinite reflectance （Ro） was compared. XRD spectra of coal shows （002）-band and γ-band, and based on fitting calculation and multi-peak separation methods, the values of 2θ002 and 2θγ can be obtained, as well as corresponding intensities I002 and Iγ, consequently the coal rank can be quantized as the ratio of I002 and Iγ, that is coal rank=I002/Iγ. The research shows that the values of θ002 and θγ increase with the metamorphic grade, and a very good linear positive correlation exists between calculated Coal Rank and Ro.展开更多
Crystals of CdSxSe1-x alloys have been grown from the vapour phase. Some of the physical properties, such as lattice parameters, crystal structure and x-rays data of CdSxSe1-x alloys were determined using x-ray diffra...Crystals of CdSxSe1-x alloys have been grown from the vapour phase. Some of the physical properties, such as lattice parameters, crystal structure and x-rays data of CdSxSe1-x alloys were determined using x-ray diffractometry. X-ray diffractometry has shown that CdS-CdSe mixed crystals had the wurtzite structure for all compositions between CdS and CdSe. The lattice parameters （both a and c） were found to show a linear dependence with composition. The dependence of the lattice parameters of a and c on composition can be expressed as： a（x） = 4.165 ＋ 0.16x; c（x） = 6.713 ＋ 0.27x. The variation of band gap with composition was determined for these samples from optical absorption measurements, which showed that the band gap varied smoothly and monotonically, but not linearly over the composition range typical results were found between 2.42-1.74 eV at room temperature.展开更多
The target products were prepared by homogeneous precipitation method using SDS and PEG 800, respectively, as surfactant at a reaction temperature of 95 ℃ for 3 h, followed by calcination at 400 ~C for 3 h. The sampl...The target products were prepared by homogeneous precipitation method using SDS and PEG 800, respectively, as surfactant at a reaction temperature of 95 ℃ for 3 h, followed by calcination at 400 ~C for 3 h. The samples were charac- terized and analyzed by XRD, SEM, FTIR and zeta potential measurements. The products were modified with different sur- factants to improve their dispersion stability, both the amount and the best zeta potential values of which were identified in this work. The surface-modified nano-particles were added at a mass fraction of 1.0%, 2.0%, 3.0%, and 4.0%, respectively, into the base oil. It was showed that the additive in base oil has good oil solubility without detectable corrosion of copper stripe, and had excellent behavior in terms of anti-wear performance and lower friction coefficient.展开更多
This is a mini-review-like article including our recent results and methods for （new） metal oxides and （previously reported） composite materials composed of metal complexes and metal oxides for comparison to enhan...This is a mini-review-like article including our recent results and methods for （new） metal oxides and （previously reported） composite materials composed of metal complexes and metal oxides for comparison to enhance anisotropic structural changes intentionally. Some complex inorganic oxides are known that they may be promising color materials （absorbing visible light of certain wavelengths region） having potential application for environmentally benign catalysts, for example, photocatalysts. Chiral copper（Ⅱ） complexes having bidentate amine ligands （[CuL2]2＋） can be acted as cationic building blocks of bimetallic metal complexes. We have prepared some chiral bimetallic complexes with various anionic metal complexes such as [PtCl4]2-, [M02O7]2 and Mn12 clusters （typical single-molecule magnets） which characterized by means of solid-state electronic and CD （circular dichroism） spectra, IR （infrared） spectra, synchrotron XRD （X-ray diffraction） and XAS （soft X-ray absorption spectroscopy）. By sintering these precursor chiral bimetallic complexes, we have prepared complex inorganic oxides from them. The IR spectra indicated substituting metal-ligand bonds and losing organic moieties. The XRD pattern indicated complete changes of crystal structures. The XAS revealed replacing coordination atoms as well as oxidation of valences of metal ions. Furthermore, we will also investigate possibility of patterning by homogeneous precipitation method as bimetallic complexes to prepare desirable complex inorganic oxides.展开更多
Self-made enriched IUB boric acid as raw material was purified by recrystallization. The effects of final crystallization temperature, crystallization time, stirring speed, crystallization frequency and other factors ...Self-made enriched IUB boric acid as raw material was purified by recrystallization. The effects of final crystallization temperature, crystallization time, stirring speed, crystallization frequency and other factors on the purity were investigated. The appropriate operating condition was that the final crystallization temperature and time were 5 ℃ and 10 h respectively under a low-speed stirring for crystallizing twice, which would make the purity and yield of boric acid reach 99.94% and 95.36%, respectively. Taking this as foundation, recrystallization process was optimized with acetone as anti-solvent, whose amount was the most important index. The boric acid solution was added into acetone and recrystallized under the same condition, and the purity and yield of boric acid would reach 99.98% and 99.61%, respectively. The product detected by XRD was confirmed as boric acid crystal. Main ion concentration in the product was detected by ICP, which basically met the national standard of high purity. Crystal morphology of boric acid was observed by SEM.展开更多
基金National Natural Science Foundation of China(12102410)Fund of National Key Laboratory of Shock Wave and Detonation Physics(JCKYS2022212005)。
文摘The lattice parameter,measured with sufficient accuracy,can be utilized to evaluate the quality of single crystals and to determine the equation of state for materials.We propose an iterative method for obtaining more precise lattice parameters using the interaction points for the pseudo-Kossel pattern obtained from laser-induced X-ray diffraction(XRD).This method has been validated by the analysis of an XRD experiment conducted on iron single crystals.Furthermore,the method was used to calculate the compression ratio and rotated angle of an LiF sample under high pressure loading.This technique provides a robust tool for in-situ characterization of structural changes in single crystals under extreme conditions.It has significant implications for studying the equation of state and phase transitions.
基金supported by the National Natural Science Foundation of China (21263015,21567016 and 21503106)the Education Department Foundation of Jiangxi Province (KJLD14005 and GJJ150016)the Natural Science Foundation of Jiangxi Province (20142BAB213013 and 20151BBE50006),which are greatly acknowledged by the authors~~
文摘A series of SnO2‐based catalysts modified by Mn, Zr, Ti and Pb oxides with a Sn/M （M=Mn, Zr, Ti and Pb） molar ratio of 9/1 were prepared by a co‐precipitation method and used for CH4 and CO oxidation. The Mn3＋, Zr4＋, Ti4＋and Pb4＋cations are incorporated into the lattice of tetragonal rutile SnO2 to form a solid solution structure. As a consequence, the surface area and thermal stability of the catalysts are improved. Moreover, the oxygen species of the modified catalysts become easier to be reduced. Therefore, the oxidation activity over the catalysts was improved, except for the one modified by Pb oxide. Manganese oxide demonstrates the best promotional effects for SnO2. Using an X‐ray diffraction extrapolation method, the lattice capacity of SnO2 for Mn2O3 was 0.135 g Mn2O3/g SnO2, which indicates that to form stable solid solution, only 21%Sn4＋cations in the lattice can be maximally replaced by Mn3＋. If the amount of Mn3＋cations is over the capacity, Mn2O3 will be formed, which is not favorable for the activity of the catalysts. The Sn rich samples with only Sn‐Mn solid solution phase show higher activity than the ones with excess Mn2O3 species.
基金Project(35060905) supported by the Doctoral Foundation of Jiangsu University of Science and Technology
文摘Twin roll cast ZK60 alloy strip/sheet with final thickness of 0.5 mm was prepared, and effect of rolling temperature on microstructure and texture development was investigated using OM and XRD technique, microstructure and texture were measured on specimens subjected to rolling experiment at different rolling temperature, and macrotexture was also evaluated by X-ray diffraction method. In addition, the （1010）and （0002） pole figures were measured, and the tensile test was performed to reveal the influence of rolling temperature on mechanical properties. The results show that the microstrucmre of ZK60 alloy sheet consisted of fibrous structure with elongated grains, and shear bands along the rolling direction after warm rolling. Dynamic recrystallization could be found during the warm rolling process at rolling temperature 350℃ and above. And many fine recrystallized grain could be observed in the shear bands area. It is a little difficult to see the recrystallized grain in the sheet warm rolled at 300℃ because of higher density of shear bands. The warm rolled ZK60 alloy sheet exhibited strong （0002） pole texture, the intensity of （0002） pole figure decreases with the increasing of rolling temperature and the basal pole tilted slightly to the transverse direction after warm rolling.
基金Supported by the Education Department of Heilongjiang Province(12541111)the Program for Innovative Research Team in University of Heilongjiang Province(2013TD008)the Key Laboratory of Green Chemical Engineering and Technology of College of Heilongjiang Province and Harbin University of Science and Technology and the Technology and Innovative Experimental Project of Harbin University of Science and Technology
文摘In this work, BiV04 powders were synthesized by a sol-gel method, and the BiV04 gels with different calcination temperature were investigated by X-ray diffraction （XRD）. Absorption range and band gap energy, which are respon- sible for the observed photocatalyst behavior, were investigated by UV/vis diffuse reflectance spectroscopy （DRS） for pure and silver oxide loaded BiV04. Pbotocatalytic properties of the prepared samples were examined by studying the degradation of the methyl orange. When using NaCI02 as an electron acceptor, the possible photocatalytic mech- anism has been discussed by photocatalytic reactions. With the help of electron acceptor, the results show clearly that the BiV04 loaded silver oxide exhibited superior photocatalytic activity in simulated dye wastewater treatment.
基金Project(2011FZ030)supported by the Natural Science Foundation of Yunnan Province,ChinaProjects(2011144,2011221)supported by Analysis and Test Foundation of Kunming University of Science and Technology,China
文摘Mesoporous CeO2 was first synthesized by hydrothermal method,and then used to synthesize different contents of CuO)x/CeO2(x:molar ratio of Cu to Ce) by deposition-precipitation method.These materials were characterized by X-ray diffraction(XRD),N2 adsorption and desorption,H2 temperature programmed reduction(H2-TPR) and O2 temperature programmed desorption(O2-TPD) to study the crystal structure,surface area,and the mechanism of CO oxidation.The results show that,on XRD patterns,no evidence of CuO diffraction peaks is present until Cu loading is increased to 20%.The BET surface area decreases noticeably with the increase of Cu content.Compared with other samples,the better reducibility and activity oxygen species of(CuO)10%/CeO2coincide with its better catalytic activity.
文摘ZnO nanorods, with the c-axis orientation used for transparent conductors, solar cells, sensors especially the functionalized ZnO nanorods with some kinds of enzymes have been used for biosensor. In this work, we describe the process immobilization of galactose oxidase on ZnO nanorods surface with glutaraldehyde as a cross-linker molecule to make the working electrode in electrochemical biosensor. ZnO nanorods were grown on FTO （Fluorine-doped tin oxide） substrate by solution method at low temperature. The crystalline phase and orientation of ZnO nanorods were identified using X-ray diffraction. The efficiency of the immobilization was calculated by Braford method showed that about 36% enzyme content was immobilized on ZnO nanorods surface. The working electrode based on the immobilized ZnO nanorods was tested in galactose solution by CV （cyclic voltammetry） method indicated the value of current intensity is about 0.14 μA. These results clearly demonstrate the potential of galactose sensor based on ZnO nanorod.
基金Supported by the National Natural Science Foundation of China （40972106） the Major Projects of the National Science and Technology of China （2011ZX05042-001-002） the Central Universities Fundamental Research Special Foundation of China （292011266）
文摘Based on analysis on X-ray diffraction, the metamorphic grade of coal in southeast Qinshui Basin was discussed, and a precise evaluation of coal rank through XRD analysis was made, in addition, the correlation of coal rank and vitrinite reflectance （Ro） was compared. XRD spectra of coal shows （002）-band and γ-band, and based on fitting calculation and multi-peak separation methods, the values of 2θ002 and 2θγ can be obtained, as well as corresponding intensities I002 and Iγ, consequently the coal rank can be quantized as the ratio of I002 and Iγ, that is coal rank=I002/Iγ. The research shows that the values of θ002 and θγ increase with the metamorphic grade, and a very good linear positive correlation exists between calculated Coal Rank and Ro.
文摘Crystals of CdSxSe1-x alloys have been grown from the vapour phase. Some of the physical properties, such as lattice parameters, crystal structure and x-rays data of CdSxSe1-x alloys were determined using x-ray diffractometry. X-ray diffractometry has shown that CdS-CdSe mixed crystals had the wurtzite structure for all compositions between CdS and CdSe. The lattice parameters （both a and c） were found to show a linear dependence with composition. The dependence of the lattice parameters of a and c on composition can be expressed as： a（x） = 4.165 ＋ 0.16x; c（x） = 6.713 ＋ 0.27x. The variation of band gap with composition was determined for these samples from optical absorption measurements, which showed that the band gap varied smoothly and monotonically, but not linearly over the composition range typical results were found between 2.42-1.74 eV at room temperature.
基金supported by the Liaoning Provincial Office of Education for Innovation Team (2006T001)Liaoning Province of Key Laboratory Project (2008403001)
文摘The target products were prepared by homogeneous precipitation method using SDS and PEG 800, respectively, as surfactant at a reaction temperature of 95 ℃ for 3 h, followed by calcination at 400 ~C for 3 h. The samples were charac- terized and analyzed by XRD, SEM, FTIR and zeta potential measurements. The products were modified with different sur- factants to improve their dispersion stability, both the amount and the best zeta potential values of which were identified in this work. The surface-modified nano-particles were added at a mass fraction of 1.0%, 2.0%, 3.0%, and 4.0%, respectively, into the base oil. It was showed that the additive in base oil has good oil solubility without detectable corrosion of copper stripe, and had excellent behavior in terms of anti-wear performance and lower friction coefficient.
文摘This is a mini-review-like article including our recent results and methods for （new） metal oxides and （previously reported） composite materials composed of metal complexes and metal oxides for comparison to enhance anisotropic structural changes intentionally. Some complex inorganic oxides are known that they may be promising color materials （absorbing visible light of certain wavelengths region） having potential application for environmentally benign catalysts, for example, photocatalysts. Chiral copper（Ⅱ） complexes having bidentate amine ligands （[CuL2]2＋） can be acted as cationic building blocks of bimetallic metal complexes. We have prepared some chiral bimetallic complexes with various anionic metal complexes such as [PtCl4]2-, [M02O7]2 and Mn12 clusters （typical single-molecule magnets） which characterized by means of solid-state electronic and CD （circular dichroism） spectra, IR （infrared） spectra, synchrotron XRD （X-ray diffraction） and XAS （soft X-ray absorption spectroscopy）. By sintering these precursor chiral bimetallic complexes, we have prepared complex inorganic oxides from them. The IR spectra indicated substituting metal-ligand bonds and losing organic moieties. The XRD pattern indicated complete changes of crystal structures. The XAS revealed replacing coordination atoms as well as oxidation of valences of metal ions. Furthermore, we will also investigate possibility of patterning by homogeneous precipitation method as bimetallic complexes to prepare desirable complex inorganic oxides.
文摘Self-made enriched IUB boric acid as raw material was purified by recrystallization. The effects of final crystallization temperature, crystallization time, stirring speed, crystallization frequency and other factors on the purity were investigated. The appropriate operating condition was that the final crystallization temperature and time were 5 ℃ and 10 h respectively under a low-speed stirring for crystallizing twice, which would make the purity and yield of boric acid reach 99.94% and 95.36%, respectively. Taking this as foundation, recrystallization process was optimized with acetone as anti-solvent, whose amount was the most important index. The boric acid solution was added into acetone and recrystallized under the same condition, and the purity and yield of boric acid would reach 99.98% and 99.61%, respectively. The product detected by XRD was confirmed as boric acid crystal. Main ion concentration in the product was detected by ICP, which basically met the national standard of high purity. Crystal morphology of boric acid was observed by SEM.
