Introduction Scaling down to the micro- and nanoscale is a strong current trend in the development of science and technology. ＇Small is energy efficient and cost effective＇ has long been for the motto of the semico...Introduction Scaling down to the micro- and nanoscale is a strong current trend in the development of science and technology. ＇Small is energy efficient and cost effective＇ has long been for the motto of the semiconductor industry, including micro- and nanoelectronics, micro-electro-mechanical systems （MEMS） and nanoelectro-mechanical systems （NEMS）.展开更多
Flexible and wearable pressure sensors hold immense promise for health monitoring,covering disease detection and postoperative rehabilitation.Developing pressure sensors with high sensitivity,wide detection range,and ...Flexible and wearable pressure sensors hold immense promise for health monitoring,covering disease detection and postoperative rehabilitation.Developing pressure sensors with high sensitivity,wide detection range,and cost-effectiveness is paramount.By leveraging paper for its sustainability,biocompatibility,and inherent porous structure,herein,a solution-processed all-paper resistive pressure sensor is designed with outstanding performance.A ternary composite paste,comprising a compressible 3D carbon skeleton,conductive polymer poly(3,4-ethylene dioxythiophene):poly(styrenesulfonate),and cohesive carbon nanotubes,is blade-coated on paper and naturally dried to form the porous composite electrode with hierachical micro-and nano-structured surface.Combined with screen-printed Cu electrodes in submillimeter finger widths on rough paper,this creates a multiscale hierarchical contact interface between electrodes,significantly enhancing sensitivity(1014 kPa-1)and expanding the detection range(up to 300 kPa)of as-resulted all-paper pressure sensor with low detection limit and power consumption.Its versatility ranges from subtle wrist pulses,robust finger taps,to large-area spatial force detection,highlighting its intricate submillimetermicrometer-nanometer hierarchical interface and nanometer porosity in the composite electrode.Ultimately,this all-paper resistive pressure sensor,with its superior sensing capabilities,large-scale fabrication potential,and cost-effectiveness,paves the way for next-generation wearable electronics,ushering in an era of advanced,sustainable technological solutions.展开更多
In this paper, the cement paste and the mortar were tested using the PF-QNM technique. It is shown that the PF-QNM technique is very powerful to characterize the mechanical properties of micro-and nanostructures in th...In this paper, the cement paste and the mortar were tested using the PF-QNM technique. It is shown that the PF-QNM technique is very powerful to characterize the mechanical properties of micro-and nanostructures in the cement-based materials. It does not have strict requirements for test environment and it does not damage the surface of the material. High-resolution images can be obtained very easily, and they can be analyzed statistically. The test results show that PF-QNM analysis can test not only the mechanical properties of the cement paste, but also investigate the interfacial regions in the cement-based material, including the variation in the mechanical properties of interface regions and the extension of the interfacial regions. During the test, care must be taken to choose the size of test area;indeed, a test area too small is not representative but too large leads to lack of stability. The recommended side is a square with a length of in the range 10-30 μm.展开更多
The reliability of industrial installation requires minimum leakage of pressurized sealed joints during operation. At the design stage, the leakage behavior of the gasket must be one of the most important parameter in...The reliability of industrial installation requires minimum leakage of pressurized sealed joints during operation. At the design stage, the leakage behavior of the gasket must be one of the most important parameter in the gasket selection. The objective of the work presented in this paper is to develop an analytical leak rate prediction methodology used in gasketed joints. A pseudo analytical-experimental innovative approach was used to estimate the characteristics of the porous structure for the purpose of predicting accurate leak rate through gaskets with different fluids under conditions similar to those of operation. The analytical model assumes the flow to be continuum but employs a slip boundary condition on the leak path wall to determine the porosity parameters of the gasket. The analytical model results are validated and confronted against experimental data which were conducted under various conditions of fluid media, pressure, gasket stress and temperature. Two experimental test rigs fully automate that accurately reproduces the real leakage behavior of the gasketed joint have been developed to analyze the mechanical and thermal effects on the gasket flow regime. The gas leaks were measured with multi-gas mass spectrometers while liquid leaks were measure using a sophisticated detection system based on the pressure rise method.展开更多
A facile method to fabricate wettability pattern(two extreme wettabilities arranged in a pattern)to realize water self-pumping is proposed on cemented carbide while not necessarily depositing other materials on substr...A facile method to fabricate wettability pattern(two extreme wettabilities arranged in a pattern)to realize water self-pumping is proposed on cemented carbide while not necessarily depositing other materials on substrate surface.The water self-pumping is achieved by arranging wedge shaped superhydrophilic domain in superhydrophobic substrate using laser machining.Through single factor experiments,it is found that the key to the extreme wettabilities,micro⁃and nano⁃structures,is rendered by laser machining processes and is influenced by laser parameters.Meanwhile,the proper laser parameters that are used to fabricate required micro-and nano⁃structures are obtained.Finally,the water transport experiment is carried out,which shows that the velocity of water bulge could be up to 362 mm/s when the wedge angle is 3°.The mechanism of the water self-pumping is analyzed and it is found that the migration of water bulge is governed by Laplace pressure of the water bulge induced by the wedge micro-groove.展开更多
Changes in trace substances in human metabolites, which are related to disease processes and health status, can serve as chemical markers for disease diagnosis and symptom monitoring. Real-time online detection is an ...Changes in trace substances in human metabolites, which are related to disease processes and health status, can serve as chemical markers for disease diagnosis and symptom monitoring. Real-time online detection is an inevitable trend for the future of health monitoring, and the construction of chips for detection faces major challenges. The response of sensors often fails to meet the requirements for chipbased detection of trace substances due to the low efficiency of interfacial heterogeneous reactions, necessitating a rational design approach for micro-and nano-structures to improve sensor performance with respect to sensitivity and detection limits. This review focuses on the influence of micro-and nanostructures that used in chip on sensing. Firstly, this review categorizes sensors into chemiresistors, electrochemical sensors, fluorescence sensors, and surface enhanced Raman scattering(SERS) sensors based on their sensing principle, which have significant applications in disease diagnosis. Subsequently, commencing from the application requirements in the field of sensing, this review focuses on the different structures of nanoparticle(NP) assemblies, including wire, layered, core-shell, hollow, concave and deformable structures. These structures change in the size, shape, and morphology of conventional structures to achieve characteristics such as ordered alignment, high specific surface area, space limitation,vertical diffusion, and swaying behavior with fluid, thereby addressing issues such as poor signal transmission efficiency, inadequate adsorption and capture capacity, and slow mass transfer speed during sensing. Finally, the design direction of micro-and nano-structures, and possible obstacles and solutions to promote chip-based detection have been discussed. It is hope that this article will inspire the exploration of interface micro-and nano-structures modulated sensing methods.展开更多
INTRODUCTION Recently,in polymer technology,there has been an evident change in the production of flexible functional film materials and devices on flexible polymer substrates.The aforementioned products are used in p...INTRODUCTION Recently,in polymer technology,there has been an evident change in the production of flexible functional film materials and devices on flexible polymer substrates.The aforementioned products are used in power engineering(light-emitting materials,solar cells),medicine(materials with incorporated drugs and other special ingredients,functionalized membranes,medical transdermal films),展开更多
We report a facile solution method to form titanium oxide(TiO_(2))nano-flower structure on the titanium(Ti)substrates for realizing good physical sterilization and biocompatibility.We first prepare TiO_(2) nanotubes(N...We report a facile solution method to form titanium oxide(TiO_(2))nano-flower structure on the titanium(Ti)substrates for realizing good physical sterilization and biocompatibility.We first prepare TiO_(2) nanotubes(NT)with a diameter of about 80-100 nm and a length of about 5μm on Ti substrates by anodization,which is utilized as precursor.Then,we employ immersion treatment in different concentrations of phosphoric acid solution at 75℃ for 5 h to realize the transformation from TiO_(2) NT to TiO_(2) nano-flower structure.In addition,we studied the effects of phosphoric acid concentration(1 wt%,2.5 wt%,5 wt% and 10 wt%)on the TiO_(2) nano-flower structure,and the antibacterial properties and biocompatibility of the TiO_(2) nano-flower structure.The results show that TiO_(2) nano-flower structure become larger and thicker with the increase in the phosphoric acid concentration,and the thickness of the coating can reach 6.88μm.Meanwhile,the TiO_(2) nano-flower structure shows good physical sterilization effect,especially for the TiO_(2) nano-flower structure formed in 10 wt%H^(3)PO_(4) solution,the antibacterial rate can reach 95%.In addition,the TiO_(2) nano-flower structure have no toxicity to the osteoblasts and support cell growth.展开更多
Various spectroscopic experiments performed on the AIRBUS ZERO G—located in Bordeaux, France—in the years 2002 to 2012 exhibit minute optical reflection/absorption changes (GIACs) as a result of gravitational change...Various spectroscopic experiments performed on the AIRBUS ZERO G—located in Bordeaux, France—in the years 2002 to 2012 exhibit minute optical reflection/absorption changes (GIACs) as a result of gravitational changes between 0 and 1.8 g in various biological species such as maize, oats, Arabidopsis and particularly Phycomyces sporangiophores. During a flight day, the AIRBUS ZERO G conducts 31 parabolas, each of which lasts about three minutes including a period of 22 s of weightlessness. So far, we participated in 11 parabolic flight campaigns including more than 1000 parabolas performing various kinds of experiments. During our campaigns, we observed an unexplainable variability of the measuring signals (GIACs). Using GPS-positioning systems and three dimensional magnetic field sensors, these finally were traced back to the changing earth’s magnetic field associated with the various flight directions. This is the first time that the interaction of gravity and the Earth’ magnetic field in the primary induction process in living system has been observed.展开更多
OM (optical microscope)/TEM (transmission electron microscope) micro- and submicrostructural analysis of hornblende rocks sheared at high temperatures from the Diancangshan area, western Yunnan reveals evidence for de...OM (optical microscope)/TEM (transmission electron microscope) micro- and submicrostructural analysis of hornblende rocks sheared at high temperatures from the Diancangshan area, western Yunnan reveals evidence for deformation in the brittle-ductile transition of hornblende at middle crustal level (about 637℃ and 0.653 GPa) and mechanisms of deformation in the transitional regime are further discussed. Sheared hornblende rocks at middle crustal level have typical mylonitic microstructures, shown by coarse porphyroclasts and fine matrix grains. Different mineral phases in the rocks show distinct deformation characteristics. Hornblende and feldspar grains are intensely deformed with ob- vious grainsize reduction, but quartz grains are recrystallized dominantly by grain growth. Hornblende grains show typical brittle-ductile transition nature. Initial crystallographic orientations of porphyro- clasts have strong effects on the behavior of grains during deformation. There are mainly two types of porphyroclasts, type I "hard" porphyroclasts and type II "soft" porphyroclasts, with [001] perpendicular and parallel to external shear stresses respectively. "Hard" porphyroclasts generally occur as compe- tent grains that are rarely deformed or sometimes deformed by fracturing and dislocation tangling. "Soft" porphyroclasts are highly deformed primarily by dislocation tangling (as shown in the cores of the porphyroclasts), but twinning, dislocation glide and climb probably due to hydrolytic weakening also contribute to dynamic recrystallization of the porphyroclasts into fine grains in the matrix. The micro- and submicrostructures of the two types of porphyroclasts and fine-grained matrix provide powerful evidence for the behavior of brittle-ductile transition of hornblende grains. It is concluded that twinning nucleation is one of the most important processes that operate during dynamic recrystalliza- tion of hornblende crystals at the brittle-ductile transition. (100) [001] twin gliding and dislocation creep (dislocation glide and climb) are mutually enhanced during twinning nucleation. As a newly discovered mechanism of dynamic recrystallization, it may have played more important roles than ever recognized during dynamic recrystallization of crystals with twins in the brittle-ductile transition.展开更多
Micro-and nanorobotic is an emerging field of research arising from the cross-fusion of micro/nano technology and robotics and has become an important part of robotics. Micro-and nanorobots have the advantages of smal...Micro-and nanorobotic is an emerging field of research arising from the cross-fusion of micro/nano technology and robotics and has become an important part of robotics. Micro-and nanorobots have the advantages of small size, low weight, large thrust-toweight ratio, high flexibility, and high sensitivity. Due to the characteristics distinguishing from macroscopic robots, micro-and nanorobots have stimulated the research interest of the scientific community and opened up numerous application fields such as drug delivery and disease diagnosis. In the past 30 years, research on micro-and nanorobots has made considerable progress.This article provides a comprehensive overview of the development of these robots. First, the application of the robots is reviewed. Then, the key components of the robots are discussed separately, covering their actuation, design, fabrication and control. In addition, from the perspectives of intelligence and sensing, clinical applications, materials and performance, the challenges that may be encountered in the development of such robots in the future are discussed. Finally, the entire article is summarized, and concepts for future micro-and nanorobots are described.展开更多
Cytochrome P450 enzyme-copper phosphate hybrid materials with flower-like shape were prepared with a simple but efficient coprecipitation method.The growth process of the hybrid flowers can be divided into three succe...Cytochrome P450 enzyme-copper phosphate hybrid materials with flower-like shape were prepared with a simple but efficient coprecipitation method.The growth process of the hybrid flowers can be divided into three successive steps：coordination/nucleation,growth,and further ripen.The concentration of enzymes in the mother liquor exerted great influence on the morphology and surface enzyme content of the nano-composites.The catalytic performance in the reaction of selective oxidation of sulfide to sulfoxide was also investigated.The hybrid flowers exhibited superior catalytic performance：satisfied thioanisole conversion and selectivity to methyl phenyl sulfoxide （both above 97%） with H2O2 as oxidant under mild reaction conditions,excellent stability and recyclability,and wide scope of substrates.Such results indicate that the hybrid materials are potentially good candidates in the industrial enzyme catalysis.展开更多
1 Results Simultaneous micro-and nanostructuring was prepared on polyolefin surfaces by injection molding.The molds were made of electropolished aluminum foil where the micropatterns were structured with a custom made...1 Results Simultaneous micro-and nanostructuring was prepared on polyolefin surfaces by injection molding.The molds were made of electropolished aluminum foil where the micropatterns were structured with a custom made robot.Nanopatterns were subsequently created on the molds by oxidizing the aluminum surface electrochemically in polyprotic acid.The preparation technique allowed simultaneous control of the dimensions of the micro-and nanostructures.Structuring has a remarkable effect on the contact angle...展开更多
Attributed to the miniaturized body size and active mobility,micro-and nanomotors(MNMs)have demonstrated tremendous potential for medical applications.However,from bench to bedside,massive efforts are needed to addres...Attributed to the miniaturized body size and active mobility,micro-and nanomotors(MNMs)have demonstrated tremendous potential for medical applications.However,from bench to bedside,massive efforts are needed to address critical issues,such as cost-effective fabrication,on-demand integration of multiple functions,biocompatibility,biodegradability,controlled propulsion and in vivo navigation.Herein,we summarize the advances of biomedical MNMs reported in the past two decades,with particular emphasis on the design,fabrication,propulsion,navigation,and the abilities of biological barriers penetration,biosensing,diagnosis,minimally invasive surgery and targeted cargo delivery.Future perspectives and challenges are discussed as well.This review can lay the foundation for the future direction of medical MNMs,pushing one step forward on the road to achieving practical theranostics using MNMs.展开更多
III-nitride materials are of great importance in the development of modern optoelectronics,but they have been limited over years by low light utilization rate and high dislocation densities in heteroepitaxial films gr...III-nitride materials are of great importance in the development of modern optoelectronics,but they have been limited over years by low light utilization rate and high dislocation densities in heteroepitaxial films grown on foreign substrate with limited refractive index contrast and large lattice mismatches.Here,we demonstrate a paradigm of high-throughput manufacturing bioinspired microstructures on warped substrates by flexible nanoimprint lithography for promoting the light extraction capability.We design a flexible nanoimprinting mold of copolymer and a two-step etching process that enable high-efficiency fabrication of nanoimprinted compound-eye-like Al2O3 microstructure(NCAM)and nanoimprinted compound-eye-like SiO_(2)microstructure(NCSM)template,achieving a 6.4-fold increase in throughput and 25%savings in economic costs over stepper projection lithography.Compared to NCAM template,we find that the NCSM template can not only improve the light extraction capability,but also modulate the morphology of AlN nucleation layer and reduce the formation of misoriented GaN grains on the inclined sidewall of microstructures,which suppresses the dislocations generated during coalescence,resulting in 40%reduction in dislocation density.This study provides a low-cost,high-quality,and high-throughput solution for manufacturing microstructures on warped surfaces of III-nitride optoelectronic devices.展开更多
Piezoelectric semiconductors bear the bifunctional photocatalysis and piezocatalysis,while the absent or weak internal charge driving force severely restricts its catalytic activity.Developing polarization strategy is...Piezoelectric semiconductors bear the bifunctional photocatalysis and piezocatalysis,while the absent or weak internal charge driving force severely restricts its catalytic activity.Developing polarization strategy is desirable,and particularly understanding its mechanism from a microscopic perspective remains scanty.Herein,we report a secondary recrystallization approach to achieving the simultaneous micro-and macroscopic polarization enhancement on Bi2WO6 nanosheets for boosting piezo-photocatalytic oxygen activation,and unravel the mechanism at an atom-level.The secondary recrystallization process not only results in a strengthened distortion of[WO6]octahedra with distortion index enhancement by~20%for a single octahedron,but also enables lateral crystal growth of nanosheets along the ab plane(av.50 to 180 nm),which separately allows the rise in dipole moment of unit cell(e.g.,1.63 D increase along a axis)and the stacking of the distorted[WO6]octahedron to accumulate the unit cell dipole,collectively contributing to the considerably strengthened spontaneous polarization and piezoelectricity.Besides,exposure of large-area{001}front facet enables more efficient capture and conversion of stress into piezo-potential.Therefore,the well-recrystallized Bi2WO6 nanosheets exhibit considerably promoted piezo-photocatalytic reactive oxygen species generation,given the decreased specific surface area.This work presents a feasible methodology to regulate inside-out polarization for guiding carriers transfer behavior,and may advance the solid understanding on the intrinsic mechanism.展开更多
Self-propelling micro-and nano-motors(MNMs)have been extensively investigated as an emerging oral drug delivery carrier for gastrointestinal(GI)tract diseases.However,the propulsion of current MNMs reported so far is ...Self-propelling micro-and nano-motors(MNMs)have been extensively investigated as an emerging oral drug delivery carrier for gastrointestinal(GI)tract diseases.However,the propulsion of current MNMs reported so far is mostly based on the redox reaction of metals(such as Zn and Mg)with severe propulsion gas generation,remaining non-degradable residue in the GI tract.Here,we develop a bioinspired enzyme-powered biopolymer micromotor mimicking the mucin penetrating behavior of Helicobacter pylori in the stomach.It converts urea to ammonia and the subsequent increase of pH induces local gel-sol transition of the mucin layer facilitating the penetration into the stomach tissue layer.The successful fabrication of micromotors is confirmed by high-resolution transmission electron microscopy,electron energy loss spectroscopy,dynamic light scattering analysis,zeta-potential analysis.In acidic condition,the immobilized urease can efficiently converted urea to ammonia,comparable with that of neutral condition because of the increase of surrounding pH during propulsion.After administration into the stomach,the micromotors show enhanced penetration and prolonged retention in the stomach for 24 h.Furthermore,histological analysis shows that the micromotors are cleared within 3 days without causing any toxicity in the GI tract.The enhanced penetration and retention of the micromotors as an active oral delivery carrier in the stomach would be successfully harnessed for the treatment of various GI tract diseases.展开更多
At the end of the 1970s,it was confirmed that dielectric multilayers can sustain Bloch surface waves(BSWs).However,BSWs were not widely studied until more recently.Taking advantage of their high-quality factor,sensing...At the end of the 1970s,it was confirmed that dielectric multilayers can sustain Bloch surface waves(BSWs).However,BSWs were not widely studied until more recently.Taking advantage of their high-quality factor,sensing applications have focused on BSWs.Thus far,no work has been performed to manipulate and control the natural surface propagations in terms of defined functions with two-dimensional(2D)components,targeting the realization of a 2D system.In this study,we demonstrate that 2D photonic components can be implemented by coating an in-plane shaped ultrathin(l/15)polymer layer on the dielectric multilayer.The presence of the polymer modifies the local effective refractive index,enabling direct manipulation of the BSW.By locally shaping the geometries of the 2D components,the BSW can be deflected,diffracted,focused and coupled with 2D freedom.Enabling BSW manipulation in 2D,the dielectric multilayer can play a new role as a robust platform for 2D optics,which can pave the way for integration in photonic chips.Multiheterodyne near-field measurements are used to study light propagation through micro-and nano-optical components.We demonstrate that a lens-shaped polymer layer can be considered as a 2D component based on the agreement between near-field measurements and theoretical calculations.Both the focal shift and the resolution of a 2D BSW lens are measured for the first time.The proposed platform enables the design of 2D all-optical integrated systems,which have numerous potential applications,including molecular sensing and photonic circuits.展开更多
Uniform flower-like TiO2 coated Au nanostars and core-shell Au@Ag nanostars with different amounts of Ag coating were prepared through a facile method by hydrolysis of TiF4 under an acidic environment. The photocataly...Uniform flower-like TiO2 coated Au nanostars and core-shell Au@Ag nanostars with different amounts of Ag coating were prepared through a facile method by hydrolysis of TiF4 under an acidic environment. The photocatalytic capability of these flower-like nanocomposites under visible light irradiation was found to be enhanced by up to 4.7-fold compared to commercial P25 TiO2 nanoparticles. The enhanced photocatalytic activity was ascribed to improved light absorption and hot electron inj ection from the photo-excited Au@Ag core to the TiO2 shell.展开更多
Lipid-based nanomedicines(LBNMs),including liposomes,lipid nanoparticles(LNPs)and extracellular vesicles(EVs),are recognized as one of the most clinically acceptable nano-formulations.However,the bench-to-bedside tran...Lipid-based nanomedicines(LBNMs),including liposomes,lipid nanoparticles(LNPs)and extracellular vesicles(EVs),are recognized as one of the most clinically acceptable nano-formulations.However,the bench-to-bedside translation efficiency is far from satisfactory,mainly due to the lack of in-depth understanding of their physical and biochemical attributes at the single-particle level.In this review,we first give a brief introduction of LBNMs,highlighting some milestones and related scientific and clinical achievements in the past several decades,as well as the grand challenges in the characterization of LBNMs.Next,we present an overview of each category of LB-NMs as well as the core properties that largely dictate their biological characteristics and clinical performance,such as size distribution,particle concentration,morphology,drug encapsulation and surface properties.Then,the recent applications of several analytical techniques including electron microscopy,atomic force microscopy,fluorescence microscopy,Raman microscopy,nanoparticle tracking analysis,tunable resistive pulse sensing and flow cytometry on the single-particle characterization of LBNMs are thoroughly discussed.Particularly,the com-parative advantages of the newly developed nano-flow cytometry that enables quantitative analysis of both the physical and biochemical characteristics of LBNMs smaller than 40 nm with high throughput and statistical ro-bustness are emphasized.The overall aim of this review article is to illustrate the importance,challenges and achievements associated with single-particle characterization of LBNMs.展开更多
文摘Introduction Scaling down to the micro- and nanoscale is a strong current trend in the development of science and technology. ＇Small is energy efficient and cost effective＇ has long been for the motto of the semiconductor industry, including micro- and nanoelectronics, micro-electro-mechanical systems （MEMS） and nanoelectro-mechanical systems （NEMS）.
基金support by the Science Fund of Shandong Laboratory of Advanced Materials and Green Manufacturing at Yantai(AMGM2021A03)the"Special Lubrication and Sealing for Aerospace"Shaanxi Provincial Science and Technology Innovation Team(2024RS-CXTD-63)+1 种基金the Xianyang2023 Key Research and Development Plan(L2023-ZDYF-QYCX-009)the World First Class University and First Class Academic Discipline Construction Funding 2023(0604024GH0201332,0604024SH0201332).
文摘Flexible and wearable pressure sensors hold immense promise for health monitoring,covering disease detection and postoperative rehabilitation.Developing pressure sensors with high sensitivity,wide detection range,and cost-effectiveness is paramount.By leveraging paper for its sustainability,biocompatibility,and inherent porous structure,herein,a solution-processed all-paper resistive pressure sensor is designed with outstanding performance.A ternary composite paste,comprising a compressible 3D carbon skeleton,conductive polymer poly(3,4-ethylene dioxythiophene):poly(styrenesulfonate),and cohesive carbon nanotubes,is blade-coated on paper and naturally dried to form the porous composite electrode with hierachical micro-and nano-structured surface.Combined with screen-printed Cu electrodes in submillimeter finger widths on rough paper,this creates a multiscale hierarchical contact interface between electrodes,significantly enhancing sensitivity(1014 kPa-1)and expanding the detection range(up to 300 kPa)of as-resulted all-paper pressure sensor with low detection limit and power consumption.Its versatility ranges from subtle wrist pulses,robust finger taps,to large-area spatial force detection,highlighting its intricate submillimetermicrometer-nanometer hierarchical interface and nanometer porosity in the composite electrode.Ultimately,this all-paper resistive pressure sensor,with its superior sensing capabilities,large-scale fabrication potential,and cost-effectiveness,paves the way for next-generation wearable electronics,ushering in an era of advanced,sustainable technological solutions.
基金Funded by the National Natural Science Foundation of China(51778582&51879235)the National Key R&D Plan(2017YFC0804809)
文摘In this paper, the cement paste and the mortar were tested using the PF-QNM technique. It is shown that the PF-QNM technique is very powerful to characterize the mechanical properties of micro-and nanostructures in the cement-based materials. It does not have strict requirements for test environment and it does not damage the surface of the material. High-resolution images can be obtained very easily, and they can be analyzed statistically. The test results show that PF-QNM analysis can test not only the mechanical properties of the cement paste, but also investigate the interfacial regions in the cement-based material, including the variation in the mechanical properties of interface regions and the extension of the interfacial regions. During the test, care must be taken to choose the size of test area;indeed, a test area too small is not representative but too large leads to lack of stability. The recommended side is a square with a length of in the range 10-30 μm.
文摘The reliability of industrial installation requires minimum leakage of pressurized sealed joints during operation. At the design stage, the leakage behavior of the gasket must be one of the most important parameter in the gasket selection. The objective of the work presented in this paper is to develop an analytical leak rate prediction methodology used in gasketed joints. A pseudo analytical-experimental innovative approach was used to estimate the characteristics of the porous structure for the purpose of predicting accurate leak rate through gaskets with different fluids under conditions similar to those of operation. The analytical model assumes the flow to be continuum but employs a slip boundary condition on the leak path wall to determine the porosity parameters of the gasket. The analytical model results are validated and confronted against experimental data which were conducted under various conditions of fluid media, pressure, gasket stress and temperature. Two experimental test rigs fully automate that accurately reproduces the real leakage behavior of the gasketed joint have been developed to analyze the mechanical and thermal effects on the gasket flow regime. The gas leaks were measured with multi-gas mass spectrometers while liquid leaks were measure using a sophisticated detection system based on the pressure rise method.
基金the National Natural Science Foundation of China(No.51875285)the Natural Science Foundation of Jiangsu Province(No.BK20190066)+1 种基金the Fundamental Research Funds for the Central Universities(No.NE2020005)the Foundation of the Graduate Innovation Center,Nanjing University of Aeronautics and Astronautics(No.kfjj20190508).
文摘A facile method to fabricate wettability pattern(two extreme wettabilities arranged in a pattern)to realize water self-pumping is proposed on cemented carbide while not necessarily depositing other materials on substrate surface.The water self-pumping is achieved by arranging wedge shaped superhydrophilic domain in superhydrophobic substrate using laser machining.Through single factor experiments,it is found that the key to the extreme wettabilities,micro⁃and nano⁃structures,is rendered by laser machining processes and is influenced by laser parameters.Meanwhile,the proper laser parameters that are used to fabricate required micro-and nano⁃structures are obtained.Finally,the water transport experiment is carried out,which shows that the velocity of water bulge could be up to 362 mm/s when the wedge angle is 3°.The mechanism of the water self-pumping is analyzed and it is found that the migration of water bulge is governed by Laplace pressure of the water bulge induced by the wedge micro-groove.
基金financially supported by the National Natural Science Foundation of China (No.21925405)。
文摘Changes in trace substances in human metabolites, which are related to disease processes and health status, can serve as chemical markers for disease diagnosis and symptom monitoring. Real-time online detection is an inevitable trend for the future of health monitoring, and the construction of chips for detection faces major challenges. The response of sensors often fails to meet the requirements for chipbased detection of trace substances due to the low efficiency of interfacial heterogeneous reactions, necessitating a rational design approach for micro-and nano-structures to improve sensor performance with respect to sensitivity and detection limits. This review focuses on the influence of micro-and nanostructures that used in chip on sensing. Firstly, this review categorizes sensors into chemiresistors, electrochemical sensors, fluorescence sensors, and surface enhanced Raman scattering(SERS) sensors based on their sensing principle, which have significant applications in disease diagnosis. Subsequently, commencing from the application requirements in the field of sensing, this review focuses on the different structures of nanoparticle(NP) assemblies, including wire, layered, core-shell, hollow, concave and deformable structures. These structures change in the size, shape, and morphology of conventional structures to achieve characteristics such as ordered alignment, high specific surface area, space limitation,vertical diffusion, and swaying behavior with fluid, thereby addressing issues such as poor signal transmission efficiency, inadequate adsorption and capture capacity, and slow mass transfer speed during sensing. Finally, the design direction of micro-and nano-structures, and possible obstacles and solutions to promote chip-based detection have been discussed. It is hope that this article will inspire the exploration of interface micro-and nano-structures modulated sensing methods.
基金supported by the Russian Foundation for Basic Research (project no.13-03-00734a)
文摘INTRODUCTION Recently,in polymer technology,there has been an evident change in the production of flexible functional film materials and devices on flexible polymer substrates.The aforementioned products are used in power engineering(light-emitting materials,solar cells),medicine(materials with incorporated drugs and other special ingredients,functionalized membranes,medical transdermal films),
基金jointly supported by the Four“Batches”Innovation Project of Invigorating Medical through Science and Technology of Shanxi Province(2022XM12)the Central Leading Science and Technology Development Foundation of Shanxi Province(YDZJSX2021A019)+1 种基金the Key Research and Development Program of Shanxi Province(202102130501007)the Natural Science Foundation of Shanxi Province(202103021223102,202203021222127).
文摘We report a facile solution method to form titanium oxide(TiO_(2))nano-flower structure on the titanium(Ti)substrates for realizing good physical sterilization and biocompatibility.We first prepare TiO_(2) nanotubes(NT)with a diameter of about 80-100 nm and a length of about 5μm on Ti substrates by anodization,which is utilized as precursor.Then,we employ immersion treatment in different concentrations of phosphoric acid solution at 75℃ for 5 h to realize the transformation from TiO_(2) NT to TiO_(2) nano-flower structure.In addition,we studied the effects of phosphoric acid concentration(1 wt%,2.5 wt%,5 wt% and 10 wt%)on the TiO_(2) nano-flower structure,and the antibacterial properties and biocompatibility of the TiO_(2) nano-flower structure.The results show that TiO_(2) nano-flower structure become larger and thicker with the increase in the phosphoric acid concentration,and the thickness of the coating can reach 6.88μm.Meanwhile,the TiO_(2) nano-flower structure shows good physical sterilization effect,especially for the TiO_(2) nano-flower structure formed in 10 wt%H^(3)PO_(4) solution,the antibacterial rate can reach 95%.In addition,the TiO_(2) nano-flower structure have no toxicity to the osteoblasts and support cell growth.
基金supported by grant BW 1025 from the DLR/BMBF(Deutsches Zentrum für Luftund Raumfahrt,and Bundesministerium für Bildung und Forschung).
文摘Various spectroscopic experiments performed on the AIRBUS ZERO G—located in Bordeaux, France—in the years 2002 to 2012 exhibit minute optical reflection/absorption changes (GIACs) as a result of gravitational changes between 0 and 1.8 g in various biological species such as maize, oats, Arabidopsis and particularly Phycomyces sporangiophores. During a flight day, the AIRBUS ZERO G conducts 31 parabolas, each of which lasts about three minutes including a period of 22 s of weightlessness. So far, we participated in 11 parabolic flight campaigns including more than 1000 parabolas performing various kinds of experiments. During our campaigns, we observed an unexplainable variability of the measuring signals (GIACs). Using GPS-positioning systems and three dimensional magnetic field sensors, these finally were traced back to the changing earth’s magnetic field associated with the various flight directions. This is the first time that the interaction of gravity and the Earth’ magnetic field in the primary induction process in living system has been observed.
基金State Key Research "973" Plan of China (Grant No. 2002CB412607)Geological Survey of China Project (Grant No. 1212010661311)+1 种基金State Key Laboratory of Geological Processes and Mineral Resources (Grant No. GPMR200637)the Project of Ministry of Science and Technology (Grant No. 2006BAB01A03)
文摘OM (optical microscope)/TEM (transmission electron microscope) micro- and submicrostructural analysis of hornblende rocks sheared at high temperatures from the Diancangshan area, western Yunnan reveals evidence for deformation in the brittle-ductile transition of hornblende at middle crustal level (about 637℃ and 0.653 GPa) and mechanisms of deformation in the transitional regime are further discussed. Sheared hornblende rocks at middle crustal level have typical mylonitic microstructures, shown by coarse porphyroclasts and fine matrix grains. Different mineral phases in the rocks show distinct deformation characteristics. Hornblende and feldspar grains are intensely deformed with ob- vious grainsize reduction, but quartz grains are recrystallized dominantly by grain growth. Hornblende grains show typical brittle-ductile transition nature. Initial crystallographic orientations of porphyro- clasts have strong effects on the behavior of grains during deformation. There are mainly two types of porphyroclasts, type I "hard" porphyroclasts and type II "soft" porphyroclasts, with [001] perpendicular and parallel to external shear stresses respectively. "Hard" porphyroclasts generally occur as compe- tent grains that are rarely deformed or sometimes deformed by fracturing and dislocation tangling. "Soft" porphyroclasts are highly deformed primarily by dislocation tangling (as shown in the cores of the porphyroclasts), but twinning, dislocation glide and climb probably due to hydrolytic weakening also contribute to dynamic recrystallization of the porphyroclasts into fine grains in the matrix. The micro- and submicrostructures of the two types of porphyroclasts and fine-grained matrix provide powerful evidence for the behavior of brittle-ductile transition of hornblende grains. It is concluded that twinning nucleation is one of the most important processes that operate during dynamic recrystalliza- tion of hornblende crystals at the brittle-ductile transition. (100) [001] twin gliding and dislocation creep (dislocation glide and climb) are mutually enhanced during twinning nucleation. As a newly discovered mechanism of dynamic recrystallization, it may have played more important roles than ever recognized during dynamic recrystallization of crystals with twins in the brittle-ductile transition.
基金supported by the National Natural Science Foundation of China(Grant Nos.61673372,91748212,61522312,U1613220,and61433017)the Key Research Program of Frontier Sciences,CAS(Grant No.QYZDB-SSW-JSC008)the CAS/SAFEA International Partnership Program for Creative Research Teams
文摘Micro-and nanorobotic is an emerging field of research arising from the cross-fusion of micro/nano technology and robotics and has become an important part of robotics. Micro-and nanorobots have the advantages of small size, low weight, large thrust-toweight ratio, high flexibility, and high sensitivity. Due to the characteristics distinguishing from macroscopic robots, micro-and nanorobots have stimulated the research interest of the scientific community and opened up numerous application fields such as drug delivery and disease diagnosis. In the past 30 years, research on micro-and nanorobots has made considerable progress.This article provides a comprehensive overview of the development of these robots. First, the application of the robots is reviewed. Then, the key components of the robots are discussed separately, covering their actuation, design, fabrication and control. In addition, from the perspectives of intelligence and sensing, clinical applications, materials and performance, the challenges that may be encountered in the development of such robots in the future are discussed. Finally, the entire article is summarized, and concepts for future micro-and nanorobots are described.
文摘Cytochrome P450 enzyme-copper phosphate hybrid materials with flower-like shape were prepared with a simple but efficient coprecipitation method.The growth process of the hybrid flowers can be divided into three successive steps：coordination/nucleation,growth,and further ripen.The concentration of enzymes in the mother liquor exerted great influence on the morphology and surface enzyme content of the nano-composites.The catalytic performance in the reaction of selective oxidation of sulfide to sulfoxide was also investigated.The hybrid flowers exhibited superior catalytic performance：satisfied thioanisole conversion and selectivity to methyl phenyl sulfoxide （both above 97%） with H2O2 as oxidant under mild reaction conditions,excellent stability and recyclability,and wide scope of substrates.Such results indicate that the hybrid materials are potentially good candidates in the industrial enzyme catalysis.
文摘1 Results Simultaneous micro-and nanostructuring was prepared on polyolefin surfaces by injection molding.The molds were made of electropolished aluminum foil where the micropatterns were structured with a custom made robot.Nanopatterns were subsequently created on the molds by oxidizing the aluminum surface electrochemically in polyprotic acid.The preparation technique allowed simultaneous control of the dimensions of the micro-and nanostructures.Structuring has a remarkable effect on the contact angle...
基金supported by the National Natural Science Foundation of China(Grant No.22175083,51973241,82001845,52072095,92163109 and 22193033)。
文摘Attributed to the miniaturized body size and active mobility,micro-and nanomotors(MNMs)have demonstrated tremendous potential for medical applications.However,from bench to bedside,massive efforts are needed to address critical issues,such as cost-effective fabrication,on-demand integration of multiple functions,biocompatibility,biodegradability,controlled propulsion and in vivo navigation.Herein,we summarize the advances of biomedical MNMs reported in the past two decades,with particular emphasis on the design,fabrication,propulsion,navigation,and the abilities of biological barriers penetration,biosensing,diagnosis,minimally invasive surgery and targeted cargo delivery.Future perspectives and challenges are discussed as well.This review can lay the foundation for the future direction of medical MNMs,pushing one step forward on the road to achieving practical theranostics using MNMs.
基金supported by the National Natural Science Foundation of China(52075394)the National Key R&D Program of China(2022YFB3603603 and 2021YFB3600204)+1 种基金the Key Research and Development Program of Hubei Province(2023BAB137)the Knowledge Innovation Program of Wuhan-Basic Research,the National Youth Talent Support Program,and the Fundamental Research Funds for the Central Universities.
文摘III-nitride materials are of great importance in the development of modern optoelectronics,but they have been limited over years by low light utilization rate and high dislocation densities in heteroepitaxial films grown on foreign substrate with limited refractive index contrast and large lattice mismatches.Here,we demonstrate a paradigm of high-throughput manufacturing bioinspired microstructures on warped substrates by flexible nanoimprint lithography for promoting the light extraction capability.We design a flexible nanoimprinting mold of copolymer and a two-step etching process that enable high-efficiency fabrication of nanoimprinted compound-eye-like Al2O3 microstructure(NCAM)and nanoimprinted compound-eye-like SiO_(2)microstructure(NCSM)template,achieving a 6.4-fold increase in throughput and 25%savings in economic costs over stepper projection lithography.Compared to NCAM template,we find that the NCSM template can not only improve the light extraction capability,but also modulate the morphology of AlN nucleation layer and reduce the formation of misoriented GaN grains on the inclined sidewall of microstructures,which suppresses the dislocations generated during coalescence,resulting in 40%reduction in dislocation density.This study provides a low-cost,high-quality,and high-throughput solution for manufacturing microstructures on warped surfaces of III-nitride optoelectronic devices.
基金the National Key Research and Development Program of China(No.2022YFB3803600)the National Natural Science Foundation of China(Nos.52272244 and 51972288)+1 种基金the Fundamental Research Funds for the Central Universities(No.2652022202)2021 Graduate Innovation Fund Project of China University of Geosciences,Beijing(No.ZY2021YC006).
文摘Piezoelectric semiconductors bear the bifunctional photocatalysis and piezocatalysis,while the absent or weak internal charge driving force severely restricts its catalytic activity.Developing polarization strategy is desirable,and particularly understanding its mechanism from a microscopic perspective remains scanty.Herein,we report a secondary recrystallization approach to achieving the simultaneous micro-and macroscopic polarization enhancement on Bi2WO6 nanosheets for boosting piezo-photocatalytic oxygen activation,and unravel the mechanism at an atom-level.The secondary recrystallization process not only results in a strengthened distortion of[WO6]octahedra with distortion index enhancement by~20%for a single octahedron,but also enables lateral crystal growth of nanosheets along the ab plane(av.50 to 180 nm),which separately allows the rise in dipole moment of unit cell(e.g.,1.63 D increase along a axis)and the stacking of the distorted[WO6]octahedron to accumulate the unit cell dipole,collectively contributing to the considerably strengthened spontaneous polarization and piezoelectricity.Besides,exposure of large-area{001}front facet enables more efficient capture and conversion of stress into piezo-potential.Therefore,the well-recrystallized Bi2WO6 nanosheets exhibit considerably promoted piezo-photocatalytic reactive oxygen species generation,given the decreased specific surface area.This work presents a feasible methodology to regulate inside-out polarization for guiding carriers transfer behavior,and may advance the solid understanding on the intrinsic mechanism.
基金This research was supported by the Basic Science Research Program(2020R1A2C3014070)the Korea Medical Device Development Fund grant(2020M3E5D8105732)+1 种基金Bio&Medical Technology Development Program(2021M3E5E7021473)the Engineering Research Center(ERC)Program(NRF-2017R1A5A1014708)of the National Research Foundation(NRF)funded by the Ministry of Science and ICT,Korea.
文摘Self-propelling micro-and nano-motors(MNMs)have been extensively investigated as an emerging oral drug delivery carrier for gastrointestinal(GI)tract diseases.However,the propulsion of current MNMs reported so far is mostly based on the redox reaction of metals(such as Zn and Mg)with severe propulsion gas generation,remaining non-degradable residue in the GI tract.Here,we develop a bioinspired enzyme-powered biopolymer micromotor mimicking the mucin penetrating behavior of Helicobacter pylori in the stomach.It converts urea to ammonia and the subsequent increase of pH induces local gel-sol transition of the mucin layer facilitating the penetration into the stomach tissue layer.The successful fabrication of micromotors is confirmed by high-resolution transmission electron microscopy,electron energy loss spectroscopy,dynamic light scattering analysis,zeta-potential analysis.In acidic condition,the immobilized urease can efficiently converted urea to ammonia,comparable with that of neutral condition because of the increase of surrounding pH during propulsion.After administration into the stomach,the micromotors show enhanced penetration and prolonged retention in the stomach for 24 h.Furthermore,histological analysis shows that the micromotors are cleared within 3 days without causing any toxicity in the GI tract.The enhanced penetration and retention of the micromotors as an active oral delivery carrier in the stomach would be successfully harnessed for the treatment of various GI tract diseases.
基金This work was supported by the Swiss National Science Foundation.
文摘At the end of the 1970s,it was confirmed that dielectric multilayers can sustain Bloch surface waves(BSWs).However,BSWs were not widely studied until more recently.Taking advantage of their high-quality factor,sensing applications have focused on BSWs.Thus far,no work has been performed to manipulate and control the natural surface propagations in terms of defined functions with two-dimensional(2D)components,targeting the realization of a 2D system.In this study,we demonstrate that 2D photonic components can be implemented by coating an in-plane shaped ultrathin(l/15)polymer layer on the dielectric multilayer.The presence of the polymer modifies the local effective refractive index,enabling direct manipulation of the BSW.By locally shaping the geometries of the 2D components,the BSW can be deflected,diffracted,focused and coupled with 2D freedom.Enabling BSW manipulation in 2D,the dielectric multilayer can play a new role as a robust platform for 2D optics,which can pave the way for integration in photonic chips.Multiheterodyne near-field measurements are used to study light propagation through micro-and nano-optical components.We demonstrate that a lens-shaped polymer layer can be considered as a 2D component based on the agreement between near-field measurements and theoretical calculations.Both the focal shift and the resolution of a 2D BSW lens are measured for the first time.The proposed platform enables the design of 2D all-optical integrated systems,which have numerous potential applications,including molecular sensing and photonic circuits.
基金supportedby the Ministry of Education of Singapore(R-143-000-607-112)the National Natural Science Foundation of China(21673155)
文摘Uniform flower-like TiO2 coated Au nanostars and core-shell Au@Ag nanostars with different amounts of Ag coating were prepared through a facile method by hydrolysis of TiF4 under an acidic environment. The photocatalytic capability of these flower-like nanocomposites under visible light irradiation was found to be enhanced by up to 4.7-fold compared to commercial P25 TiO2 nanoparticles. The enhanced photocatalytic activity was ascribed to improved light absorption and hot electron inj ection from the photo-excited Au@Ag core to the TiO2 shell.
基金We are grateful to the National Natural Science Foundation of China(21934004,21627811)the National Key R&D Program of China(2021YFA0909400)the Natural Science Foundation of Fujian Province(2022J01329)for financial support.
文摘Lipid-based nanomedicines(LBNMs),including liposomes,lipid nanoparticles(LNPs)and extracellular vesicles(EVs),are recognized as one of the most clinically acceptable nano-formulations.However,the bench-to-bedside translation efficiency is far from satisfactory,mainly due to the lack of in-depth understanding of their physical and biochemical attributes at the single-particle level.In this review,we first give a brief introduction of LBNMs,highlighting some milestones and related scientific and clinical achievements in the past several decades,as well as the grand challenges in the characterization of LBNMs.Next,we present an overview of each category of LB-NMs as well as the core properties that largely dictate their biological characteristics and clinical performance,such as size distribution,particle concentration,morphology,drug encapsulation and surface properties.Then,the recent applications of several analytical techniques including electron microscopy,atomic force microscopy,fluorescence microscopy,Raman microscopy,nanoparticle tracking analysis,tunable resistive pulse sensing and flow cytometry on the single-particle characterization of LBNMs are thoroughly discussed.Particularly,the com-parative advantages of the newly developed nano-flow cytometry that enables quantitative analysis of both the physical and biochemical characteristics of LBNMs smaller than 40 nm with high throughput and statistical ro-bustness are emphasized.The overall aim of this review article is to illustrate the importance,challenges and achievements associated with single-particle characterization of LBNMs.
