Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturba...Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturbance suppression and have poor performance in suppressing complex nonlinear disturbances.In order to address these issues,this paper proposes an improved two-degree-of-freedom LADRC(TDOF-LADRC)strategy,which can enhance the disturbance rejection performance of the system while decoupling entirely the system's dynamic and anti-disturbance performance to boost the system robustness and simplify controller parameter tuning.PMSM models that consider total disturbances are developed to design the TDOF-LADRC speed controller accurately.Moreover,to evaluate the control performance of the TDOF-LADRC strategy,its stability is proven,and the influence of each controller parameter on the system control performance is analyzed.Based on it,a comparison is made between the disturbance observation ability and anti-disturbance performance of TDOF-LADRC and CLADRC to prove the superiority of TDOF-LADRC in rejecting disturbances.Finally,experiments are performed on a 750 W PMSM experimental platform,and the results demonstrate that the proposed TDOF-LADRC exhibits the properties of two degrees of freedom and improves the disturbance rejection performance of the PMSM system.展开更多
单相开路故障的五相永磁同步电机(permanent-magnet synchronous motor,PMSM)采用有限集模型预测转矩和磁链控制(finite-control-set model predictive torque and flux control,FCS-MPTFC)策略,存在转矩脉动大、价值函数的权重系数整...单相开路故障的五相永磁同步电机(permanent-magnet synchronous motor,PMSM)采用有限集模型预测转矩和磁链控制(finite-control-set model predictive torque and flux control,FCS-MPTFC)策略,存在转矩脉动大、价值函数的权重系数整定困难、迭代计算量大以及共模电压(commonmode voltage,CMV)高等问题。为此,该文提出一种简化FCS-MPTFC策略。首先,建立五相PMSM在单相开路故障情况下的数学模型,并分析CMV产生的机理。其次,以抑制3次谐波电流的原则合成等幅值虚拟电压矢量(virtual voltage vector,V^(3)),并将转矩和磁链价值函数等效转化为电压价值函数,同时采用无差拍控制思想计算出参考电压矢量,进而通过合理划分扇区,直接获得最优V^(3)。最后,选择方向相反的两个基电压矢量代替零矢量,以减小开路故障下的CMV。仿真和实验结果表明:所提控制策略不仅能抑制单相开路故障导致的转矩脉动、降低计算负荷和CMV、抑制电流谐波,而且具有优良的稳态和动态性能。展开更多
Two model reference adaptive system （MRAS） estimators are developed for identifying the parameters of permanent magnet synchronous motors （PMSM） based on the Lyapunov stability theorem and the Popov stability crit...Two model reference adaptive system （MRAS） estimators are developed for identifying the parameters of permanent magnet synchronous motors （PMSM） based on the Lyapunov stability theorem and the Popov stability criterion, respectively. The proposed estimators only need online measurement of currents, voltages, and rotor speed to effectively estimate stator resistance, inductance, and rotor flux-linkage simultaneously. The performance of the estimators is compared and verified through simulations and experiments, which show that the two estimators are simple, have good robustness against parameter variation, and are accurate in parameter tracking. However, the estimator based on the Popov stability criterion, which can overcome parameter variation in a practical system, is superior in terms of response speed and convergence speed since there are both proportional and integral units in the estimator, in contrast to only one integral unit in the estimator based on the Lyapunov stability theorem. In addition, the estimator based on the Popov stability criterion does not need the expertise that is required in designing a Lyapunov function.展开更多
Permanent magnet synchronous motors(PMSMs)have been widely employed in the industry. Finite-control-set model predictive control(FCS-MPC), as an advanced control scheme, has been developed and applied to improve the p...Permanent magnet synchronous motors(PMSMs)have been widely employed in the industry. Finite-control-set model predictive control(FCS-MPC), as an advanced control scheme, has been developed and applied to improve the performance and efficiency of the holistic PMSM drive systems. Based on the three elements of model predictive control, this paper provides an overview of the superiority of the FCS-MPC control scheme and its shortcomings in current applications. The problems of parameter mismatch, computational burden, and unfixed switching frequency are summarized. Moreover, other performance improvement schemes, such as the multi-vector application strategy, delay compensation scheme, and weight factor adjustment, are reviewed. Finally, future trends in this field is discussed, and several promising research topics are highlighted.展开更多
This paper presents an analysis based on analytical method for solid rotor motors for determining the rotor eddy current losses due to the current harmonics of the stator winding. The accuracy of the analytical result...This paper presents an analysis based on analytical method for solid rotor motors for determining the rotor eddy current losses due to the current harmonics of the stator winding. The accuracy of the analytical results is verified by experiments.展开更多
Aiming at the control problem of strongly nonlinear and coupled permanent magnet synchronous motor(PMSM)oil rig,this paper presents a predictive control method based on dynamic matrix model.In this method,the dynamic ...Aiming at the control problem of strongly nonlinear and coupled permanent magnet synchronous motor(PMSM)oil rig,this paper presents a predictive control method based on dynamic matrix model.In this method,the dynamic matrix algorithm using multistep prediction technique is applied to the speed loop control of the motor vector control.And its control effect is compared with the traditional proportional integral(PI)control of the motor.By comparing the initial dynamic response and the steady-state recovery under load interference of the two methods,it is shown that the dynamic response and the robustness of the motor controlled by the new method is better than that controlled by conventional PI method.And the feasibility of new control in the application of PMSM oil rig is verified.展开更多
Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model...Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model predictive flux control(MPFC)method is proposed.First,establish a mathematical model between the motor torque and the stator flux linkage according to the mathematical equations of PMSM.Thus,the control of the motor torque and stator flux linkage in the MPTC is transformed into the control of a single stator flux linkage vector,omitting the cumbersome weight setting process in the traditional MPTC.The midpoint potential control strategy is proposed,which uses the characteristics of redundant small vectors to balance the midpoint potential.After that,a fine-division strategy is proposed,which effectively reduces the number of candidate vectors and the computational burden of the system.Finally,the proposed MPFC is compared with MPTC by simulation.The results show that the proposed fine-division MPFC effectively reduces the system calculation,and has the advantages of simple principle and better dynamic and steady-state control performance.The feasibility of the control strategy is verified.展开更多
Employing matrix converter （MC） as driving mode, the strategy of model predictive torque control （MPTC） is proposed for three phase permanent magnet synchronous motor （PMSM） system. MC is applied instead of conv...Employing matrix converter （MC） as driving mode, the strategy of model predictive torque control （MPTC） is proposed for three phase permanent magnet synchronous motor （PMSM） system. MC is applied instead of conventional AC DC AC converter to increase the power factor （PF） of the system input side. MPTC is used to select optimal voltage space vector to enable the system to have satisfactory torque and flux control effect. The resultant MPTC strategy not only makes the MC fed PMSM system operate reliably and have perfect control performance, but also makes the PF of the system input side be 1. Compared with direct torque control （DTC）, the proposed MPTC strategy guarantees that MC fed PMSM has better command following characteristics in the presence of variation of load torque and tracking reference speed. Simulation results verify the feasibility and effectiveness of the proposed strategy.展开更多
A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly forme...A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.展开更多
As a driving motor, surface mounted permanent magnet synchronous motor exhibits high efficiency and high power density. However, it is susceptible to suffer irreversible demagnetization and insulation failure of coils...As a driving motor, surface mounted permanent magnet synchronous motor exhibits high efficiency and high power density. However, it is susceptible to suffer irreversible demagnetization and insulation failure of coils under severe thermal load condition. Therefore, it is essential to predict temperattrre distribution in the driving motor. In this paper, a lumped parameter thermal mode/of surface mounted permanent magnet is investigated. By using finite element method, the iron loss distribution in various parts of the driving motor is achieved. Moreover, the influences of interface gap and flow rate on temperature distribution are discussed. Finally, the simulation of temperature distribution in different parts of the driving motor is achieved. The presented methodology contributes to verify the feasibility of the driving motor design.展开更多
针对传统谐振控制器与PI控制器并联(PIR)无法克服积分环节饱和等因素引起的系统动态过程中超调震荡问题,提出了一种改进双环自抗扰谐振控制器(dual-loop active disturbance rejection control,DLADRC)。DLADRC速度环与电流环均采用自...针对传统谐振控制器与PI控制器并联(PIR)无法克服积分环节饱和等因素引起的系统动态过程中超调震荡问题,提出了一种改进双环自抗扰谐振控制器(dual-loop active disturbance rejection control,DLADRC)。DLADRC速度环与电流环均采用自抗扰控制,速度环采用传统的自抗扰控制。电流环采用一种改进的谐振扩张状态观测器,将观测电流作为谐振控制器的输入,令谐振控制器的输出直接作用到电流环输出,从而降低了谐振电流环设计的复杂性。双环自抗扰谐振控制器保留了谐振控制器抑制特定频率谐波电流的特性,同时优化了系统的超调量与调节时间,有效提升了谐振控制系统的动态性能。仿真结果验证DLADRC系统的有效性。展开更多
Permanent magnet synchronous motor（PMSM） displays chaotic osdllation with certain parameter values, which threatens the secure operation of the power system. To control these unwanted chaotic oscillations, a new con...Permanent magnet synchronous motor（PMSM） displays chaotic osdllation with certain parameter values, which threatens the secure operation of the power system. To control these unwanted chaotic oscillations, a new control scheme which depended on external torque was designed. Based on Lyapunov stability theorem and the matrix theory, several sufficient conditions were derived, which ensured the global asymptotic stability and exponential stability for the chaotic PMSM with uncertain pulse disturbance. The designed controller based on external torque was able to eliminate the chaotic oscillations. A numerical example was given to demonstrate the effectiveness of the proposed results.展开更多
在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MP...在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MPFTC来实现相开路和短路故障情况下的统一容错控制。首先,将模型预测电流控制的电流代价函数等效转化为电压代价函数,并采用无差拍方法通过电流模型计算出参考电压。然后,基于抑制三次谐波电流为0的原则合成虚拟电压矢量(virtual voltage vector,V^(3));通过重构V^(3)和扇区,以直接获得参考电压矢量对应的最优电压矢量。最后,对传统和简化FCS-MPFTC在开路和短路故障下进行对比实验。结果表明,所提策略能够有效减小故障后计算量、转矩脉动以及电流谐波含量。展开更多
文摘Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturbance suppression and have poor performance in suppressing complex nonlinear disturbances.In order to address these issues,this paper proposes an improved two-degree-of-freedom LADRC(TDOF-LADRC)strategy,which can enhance the disturbance rejection performance of the system while decoupling entirely the system's dynamic and anti-disturbance performance to boost the system robustness and simplify controller parameter tuning.PMSM models that consider total disturbances are developed to design the TDOF-LADRC speed controller accurately.Moreover,to evaluate the control performance of the TDOF-LADRC strategy,its stability is proven,and the influence of each controller parameter on the system control performance is analyzed.Based on it,a comparison is made between the disturbance observation ability and anti-disturbance performance of TDOF-LADRC and CLADRC to prove the superiority of TDOF-LADRC in rejecting disturbances.Finally,experiments are performed on a 750 W PMSM experimental platform,and the results demonstrate that the proposed TDOF-LADRC exhibits the properties of two degrees of freedom and improves the disturbance rejection performance of the PMSM system.
文摘单相开路故障的五相永磁同步电机(permanent-magnet synchronous motor,PMSM)采用有限集模型预测转矩和磁链控制(finite-control-set model predictive torque and flux control,FCS-MPTFC)策略,存在转矩脉动大、价值函数的权重系数整定困难、迭代计算量大以及共模电压(commonmode voltage,CMV)高等问题。为此,该文提出一种简化FCS-MPTFC策略。首先,建立五相PMSM在单相开路故障情况下的数学模型,并分析CMV产生的机理。其次,以抑制3次谐波电流的原则合成等幅值虚拟电压矢量(virtual voltage vector,V^(3)),并将转矩和磁链价值函数等效转化为电压价值函数,同时采用无差拍控制思想计算出参考电压矢量,进而通过合理划分扇区,直接获得最优V^(3)。最后,选择方向相反的两个基电压矢量代替零矢量,以减小开路故障下的CMV。仿真和实验结果表明:所提控制策略不仅能抑制单相开路故障导致的转矩脉动、降低计算负荷和CMV、抑制电流谐波,而且具有优良的稳态和动态性能。
基金supported by China Scholarship Council, National Natural Science Foundation of China (No. 60634020)Scientific Research Foundation of Education Ministry for the Doctors(No. 20060532026)
文摘Two model reference adaptive system （MRAS） estimators are developed for identifying the parameters of permanent magnet synchronous motors （PMSM） based on the Lyapunov stability theorem and the Popov stability criterion, respectively. The proposed estimators only need online measurement of currents, voltages, and rotor speed to effectively estimate stator resistance, inductance, and rotor flux-linkage simultaneously. The performance of the estimators is compared and verified through simulations and experiments, which show that the two estimators are simple, have good robustness against parameter variation, and are accurate in parameter tracking. However, the estimator based on the Popov stability criterion, which can overcome parameter variation in a practical system, is superior in terms of response speed and convergence speed since there are both proportional and integral units in the estimator, in contrast to only one integral unit in the estimator based on the Lyapunov stability theorem. In addition, the estimator based on the Popov stability criterion does not need the expertise that is required in designing a Lyapunov function.
基金supported in part by the National Natural Science Foundation of China(51875261)the Postgraduate Research and Practice Innovation Program of Jiangsu Province(KYCX21_3331)+1 种基金the Faculty of Agricultural Equipment of Jiangsu University(NZXB20210103)。
文摘Permanent magnet synchronous motors(PMSMs)have been widely employed in the industry. Finite-control-set model predictive control(FCS-MPC), as an advanced control scheme, has been developed and applied to improve the performance and efficiency of the holistic PMSM drive systems. Based on the three elements of model predictive control, this paper provides an overview of the superiority of the FCS-MPC control scheme and its shortcomings in current applications. The problems of parameter mismatch, computational burden, and unfixed switching frequency are summarized. Moreover, other performance improvement schemes, such as the multi-vector application strategy, delay compensation scheme, and weight factor adjustment, are reviewed. Finally, future trends in this field is discussed, and several promising research topics are highlighted.
文摘This paper presents an analysis based on analytical method for solid rotor motors for determining the rotor eddy current losses due to the current harmonics of the stator winding. The accuracy of the analytical results is verified by experiments.
基金Open Fund Project of State Key Laboratory of Large Electric Transmission Systems and Equipment Technology(No.2012AA052903)
文摘Aiming at the control problem of strongly nonlinear and coupled permanent magnet synchronous motor(PMSM)oil rig,this paper presents a predictive control method based on dynamic matrix model.In this method,the dynamic matrix algorithm using multistep prediction technique is applied to the speed loop control of the motor vector control.And its control effect is compared with the traditional proportional integral(PI)control of the motor.By comparing the initial dynamic response and the steady-state recovery under load interference of the two methods,it is shown that the dynamic response and the robustness of the motor controlled by the new method is better than that controlled by conventional PI method.And the feasibility of new control in the application of PMSM oil rig is verified.
基金National Natural Science Foundation of China(No.51867012)。
文摘Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model predictive flux control(MPFC)method is proposed.First,establish a mathematical model between the motor torque and the stator flux linkage according to the mathematical equations of PMSM.Thus,the control of the motor torque and stator flux linkage in the MPTC is transformed into the control of a single stator flux linkage vector,omitting the cumbersome weight setting process in the traditional MPTC.The midpoint potential control strategy is proposed,which uses the characteristics of redundant small vectors to balance the midpoint potential.After that,a fine-division strategy is proposed,which effectively reduces the number of candidate vectors and the computational burden of the system.Finally,the proposed MPFC is compared with MPTC by simulation.The results show that the proposed fine-division MPFC effectively reduces the system calculation,and has the advantages of simple principle and better dynamic and steady-state control performance.The feasibility of the control strategy is verified.
基金National Natural Science Foundation of China(No.61463025)Program for Excellent Team of Scientific Research in Lanzhou Jiaotong University(No.201701)
文摘Employing matrix converter （MC） as driving mode, the strategy of model predictive torque control （MPTC） is proposed for three phase permanent magnet synchronous motor （PMSM） system. MC is applied instead of conventional AC DC AC converter to increase the power factor （PF） of the system input side. MPTC is used to select optimal voltage space vector to enable the system to have satisfactory torque and flux control effect. The resultant MPTC strategy not only makes the MC fed PMSM system operate reliably and have perfect control performance, but also makes the PF of the system input side be 1. Compared with direct torque control （DTC）, the proposed MPTC strategy guarantees that MC fed PMSM has better command following characteristics in the presence of variation of load torque and tracking reference speed. Simulation results verify the feasibility and effectiveness of the proposed strategy.
基金supported by National Natural Science Foundation of China(61075065,60774045,61473314,U1134108)Ph.D.Programs Foundation of Ministry of Education of China(20110162110041)Science Foundation of Innovation Research Groups of National Natural Science Foundation of China(61321003)
基金Project (60835004) supported by the National Natural Science Foundation of China
文摘A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.
文摘As a driving motor, surface mounted permanent magnet synchronous motor exhibits high efficiency and high power density. However, it is susceptible to suffer irreversible demagnetization and insulation failure of coils under severe thermal load condition. Therefore, it is essential to predict temperattrre distribution in the driving motor. In this paper, a lumped parameter thermal mode/of surface mounted permanent magnet is investigated. By using finite element method, the iron loss distribution in various parts of the driving motor is achieved. Moreover, the influences of interface gap and flow rate on temperature distribution are discussed. Finally, the simulation of temperature distribution in different parts of the driving motor is achieved. The presented methodology contributes to verify the feasibility of the driving motor design.
文摘针对传统谐振控制器与PI控制器并联(PIR)无法克服积分环节饱和等因素引起的系统动态过程中超调震荡问题,提出了一种改进双环自抗扰谐振控制器(dual-loop active disturbance rejection control,DLADRC)。DLADRC速度环与电流环均采用自抗扰控制,速度环采用传统的自抗扰控制。电流环采用一种改进的谐振扩张状态观测器,将观测电流作为谐振控制器的输入,令谐振控制器的输出直接作用到电流环输出,从而降低了谐振电流环设计的复杂性。双环自抗扰谐振控制器保留了谐振控制器抑制特定频率谐波电流的特性,同时优化了系统的超调量与调节时间,有效提升了谐振控制系统的动态性能。仿真结果验证DLADRC系统的有效性。
基金National Natural Science Foundation of China(No.61573095)Natural Science Foundation of Shanghai,China(No.15ZR1401800)
文摘Permanent magnet synchronous motor（PMSM） displays chaotic osdllation with certain parameter values, which threatens the secure operation of the power system. To control these unwanted chaotic oscillations, a new control scheme which depended on external torque was designed. Based on Lyapunov stability theorem and the matrix theory, several sufficient conditions were derived, which ensured the global asymptotic stability and exponential stability for the chaotic PMSM with uncertain pulse disturbance. The designed controller based on external torque was able to eliminate the chaotic oscillations. A numerical example was given to demonstrate the effectiveness of the proposed results.
文摘在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MPFTC来实现相开路和短路故障情况下的统一容错控制。首先,将模型预测电流控制的电流代价函数等效转化为电压代价函数,并采用无差拍方法通过电流模型计算出参考电压。然后,基于抑制三次谐波电流为0的原则合成虚拟电压矢量(virtual voltage vector,V^(3));通过重构V^(3)和扇区,以直接获得参考电压矢量对应的最优电压矢量。最后,对传统和简化FCS-MPFTC在开路和短路故障下进行对比实验。结果表明,所提策略能够有效减小故障后计算量、转矩脉动以及电流谐波含量。
