The effect of annealing temperature on the martensitic transformation of a Ti49.2Ni50.8 alloy processed by equal channel angular pressing （ECAP） was investigated by X-ray diffraction （XRD）, transmission electron m...The effect of annealing temperature on the martensitic transformation of a Ti49.2Ni50.8 alloy processed by equal channel angular pressing （ECAP） was investigated by X-ray diffraction （XRD）, transmission electron microscopy （TEM） and differential scanning calorimetry （DSC）. The as-ECAP processed and subsequently annealed Ti49.2Ni50.8 alloys consist of B2 parent phase, Ti4Ni2O phase and B19′ martensite at room temperature. Upon cooling, all samples show B2→R→B19′ two-stage transformation. Upon heating, when the annealing temperature is less than 400℃, the samples show B19′→R→B2 two-stage transformation; when the annealing temperature is higher than 500 ℃, the samples show B19′→B2 single-stage transformation. The B2-R transformation is characterized by wide interval due to the dislocations introduced during ECAP.展开更多
A kind of micro/nanostructured 2205 duplex stainless steel(DSS)with uniform distribution of nanocrystals was prepared via aluminothermic reaction method.The analysis of stress-strain curve showed that the fracture str...A kind of micro/nanostructured 2205 duplex stainless steel(DSS)with uniform distribution of nanocrystals was prepared via aluminothermic reaction method.The analysis of stress-strain curve showed that the fracture strength and elongation of the specimen were 946 MPa and 24.7%,respectively.At present,the research on microstructure of bimodal 2205 DSS at room temperature(RT)mainly depended on scanning electron microscope(SEM)observation after loading experiments.The test result indicates that there are two different yield stages in stress-strain curve of specimen during tensile process.The microstructure of duplex bimodal structured stainless steel consists of two pairs of soft hard regions and phases.By studying deformation mechanism of bimodal structured stainless steel,the interaction between soft phase and hard phase are discussed.The principle of composition design and microstructure control of typical duplex stainless steel is obtained,which provides an important research basis for designing of advanced duplex stainless steel.展开更多
The results of XPS measurements of commercially pure titanium cp-Ti) before and after chemical treatment are presented. We have measured XPS spectra of core levels (Ti 2p, O 1s, C 1s, F 1s) and valence bands of coarse...The results of XPS measurements of commercially pure titanium cp-Ti) before and after chemical treatment are presented. We have measured XPS spectra of core levels (Ti 2p, O 1s, C 1s, F 1s) and valence bands of coarse-grained cp-Ti before and after standard acid treatment accepted in dentistry (in 1% HF and 40% HF for 1 min). It is found, that acid treatment of cp-Ti reduces the content of hydrocarbons increasing the surface energy and bio-compatibility of Ti-implants. On the other hand, it is fixed that oxygen concentration on the surface of the acid treated cp-Ti is much higher than for the untreated sample, because the acid treatment removes the contaminated surface layers, increases their reactivity, provides a better passivation and formation of thick protecting TiO2 layer.展开更多
In order to explore the exact nature of deformation defects previously observed in nanostructured Al-Mg alloys subjected to severe plastic deformation, a more thorough examination of the radiation effect on the format...In order to explore the exact nature of deformation defects previously observed in nanostructured Al-Mg alloys subjected to severe plastic deformation, a more thorough examination of the radiation effect on the formation of the planar defects in the high pressure torsion （HPT） alloys was conducted using high-resolution transmission electron microscopy （HRTEM）. The results show that high density defects in the HRTEM images disappear completely when these images are exposed under the electron beam for some duration of time. At the same time, lattice defects are never observed within no-defect areas even when the beam-exposure increases to the degree that holes appear in the areas. Therefore, it is confirmed that the planar defects observed in the HPT alloys mainly result from the significant plastic deformation and are not due to the radiation effect during HRTEM observation.展开更多
To have an insight into the occurrence of inverse Hall-Petch relationship in ultrafine-grained(UFG) aluminum alloys produced by severe plastic deformation(SPD),ultra-SPD(i.e.inducing several ten thousand shear strains...To have an insight into the occurrence of inverse Hall-Petch relationship in ultrafine-grained(UFG) aluminum alloys produced by severe plastic deformation(SPD),ultra-SPD(i.e.inducing several ten thousand shear strains via high-pressure torsion,HPT) followed by aging is applied to an Al-La-Ce alloy.Average nanograin sizes of 40 and 80 nm are successfully achieved together with strain-induced Lomer-Cottrell dislocation lock formation and aging-induced semi-coherent Al_(11)(La,Ce)_3 precipitation.Analysis of hardening mechanisms in this alloy compared to SPD-processed pure aluminum with micrometer grain sizes,SPD-processed Al-based alloys with submicrometer grain sizes and ultra-SPD-processed Al-Ca alloy with nanograin sizes reveals the presence of two breaks in the Hall-Petch relationship.First,a positive upbreak appears when the grain sizes decrease from micrometer to submicrometer which is due to extra hardening by solute-dislocation interactions.Second,a negative down-break and softening occur by decreasing the grain sizes from submicrometer to nanometer which is caused by weakening the dislocation hardening mechanism with minor contribution of the inverse Hall-Petch mechanism.Detailed analyses confirm that nanograin formation is not necessarily a solution for extra hardening of Al-based alloys and other accompanying strategies such as grain-boundary segregation and precipitation are required to overcome such a down-break and softening.展开更多
Deformation twins and stacking faults were observed in nanostructure A1-Mg alloys subjected to high pressure torsion. These observations are surprising because deformation twinnings have never been observed in their c...Deformation twins and stacking faults were observed in nanostructure A1-Mg alloys subjected to high pressure torsion. These observations are surprising because deformation twinnings have never been observed in their coarse-grained counterparts under normal conditions. Experimental evidences are introduced on non-equilibrium grain boundaries, deformation twinnings and partial dislocation emissions from grain boundaries. Some of these features can be explained by the results reported from molecular-dynamics simulations of pure FCC metals. Special emphasis is laid on the recent observations of high density hexagonal and rhombic shaped nanostructures with an average size of 3 nm in the A1-Mg alloys processed by high pressure torsion. A possible formation process of these nanostructures is proposed based on molecular-dynamics simulations.展开更多
Ti Ni alloys, with their unique shape memory effects and super elastic properties, occupy an indispensable place in the family of metallic biomaterials. In the past years, surface treatment is the main technique to im...Ti Ni alloys, with their unique shape memory effects and super elastic properties, occupy an indispensable place in the family of metallic biomaterials. In the past years, surface treatment is the main technique to improve the bioinert nature of microcrystalline Ti Ni alloys and inhibit on the release of toxic nickel ions to obtain excellent osteogenesis and osseointegration function. In the present study, nanocrystalline Ti49.2Ni50.8 alloy has been fabricated via equal channel angular pressing(ECAP), and the in vitro and in vivo studies revealed that it had enhanced cell viability, adhesion, proliferation, ALP(Alkaline phosphatase)activity and mineralization, and increased periphery thickness of new bone, in comparison to the commercial coarse-grained counterpart. These findings indicate that the reduction of grain size is beneficial to increasing the biocompatibility of Ti49.2Ni50.8 shape memory alloy.展开更多
High-pressure torsion(HPT)processing under a pressure of 6.0 GPa was applied to Ti29.7Ni50.3Hf20(at.%)alloy.Two types of structure were observed after HPT with 3 revolutions:first one is the mixture of amorphous phase...High-pressure torsion(HPT)processing under a pressure of 6.0 GPa was applied to Ti29.7Ni50.3Hf20(at.%)alloy.Two types of structure were observed after HPT with 3 revolutions:first one is the mixture of amorphous phase and retained nanocrystalline;second is the alternating bands of amorphous phase and high defect density crystalline.As a result,post deformation annealing(PDA)at 500-700℃leads to the non-uniform distribution of martensite and parent phase grains.The grains of martensite are twice larger compared to that of parent phase.The nanocrystalline and ultrafine grains form after annealing at 500-600℃and 700℃,respectively.The twinning mechanism does not change with the reduction of martensitic grains up to^35 nm.The relationship between strength and grain size in Ti29.7Ni50.3Hf20 alloy obeys the classical Hall-Petch relationship with a coefficient of 10.80±0.39 GPa nm^1/2.展开更多
基金Project(51001035)supported by the National Natural Science Foundation of ChinaProject(LBH-Q14035)supported by the Postdoctoral Funds for Scientific Research Initiation of Heilongjiang Province,ChinaProject(HEUCF20151002)supported by the Fundamental Research Funds for the Central Universities,China
文摘The effect of annealing temperature on the martensitic transformation of a Ti49.2Ni50.8 alloy processed by equal channel angular pressing （ECAP） was investigated by X-ray diffraction （XRD）, transmission electron microscopy （TEM） and differential scanning calorimetry （DSC）. The as-ECAP processed and subsequently annealed Ti49.2Ni50.8 alloys consist of B2 parent phase, Ti4Ni2O phase and B19′ martensite at room temperature. Upon cooling, all samples show B2→R→B19′ two-stage transformation. Upon heating, when the annealing temperature is less than 400℃, the samples show B19′→R→B2 two-stage transformation; when the annealing temperature is higher than 500 ℃, the samples show B19′→B2 single-stage transformation. The B2-R transformation is characterized by wide interval due to the dislocations introduced during ECAP.
基金Funded by the National Natural Science Foundation of China(No.51911530119)the Department of Education of Gansu Province Innovation Fund(No.2021A-023)the Open Fund Project of Key Laboratory of Solar Power System Engineering Project(No.2022SPKL01)。
文摘A kind of micro/nanostructured 2205 duplex stainless steel(DSS)with uniform distribution of nanocrystals was prepared via aluminothermic reaction method.The analysis of stress-strain curve showed that the fracture strength and elongation of the specimen were 946 MPa and 24.7%,respectively.At present,the research on microstructure of bimodal 2205 DSS at room temperature(RT)mainly depended on scanning electron microscope(SEM)observation after loading experiments.The test result indicates that there are two different yield stages in stress-strain curve of specimen during tensile process.The microstructure of duplex bimodal structured stainless steel consists of two pairs of soft hard regions and phases.By studying deformation mechanism of bimodal structured stainless steel,the interaction between soft phase and hard phase are discussed.The principle of composition design and microstructure control of typical duplex stainless steel is obtained,which provides an important research basis for designing of advanced duplex stainless steel.
文摘The results of XPS measurements of commercially pure titanium cp-Ti) before and after chemical treatment are presented. We have measured XPS spectra of core levels (Ti 2p, O 1s, C 1s, F 1s) and valence bands of coarse-grained cp-Ti before and after standard acid treatment accepted in dentistry (in 1% HF and 40% HF for 1 min). It is found, that acid treatment of cp-Ti reduces the content of hydrocarbons increasing the surface energy and bio-compatibility of Ti-implants. On the other hand, it is fixed that oxygen concentration on the surface of the acid treated cp-Ti is much higher than for the untreated sample, because the acid treatment removes the contaminated surface layers, increases their reactivity, provides a better passivation and formation of thick protecting TiO2 layer.
基金Project (50971087) supported by the National Natural Science Foundation of ChinaProject (BK2012715) supported by the Basic Research Program (Natural Science Foundation) of Jiangsu Province, China+1 种基金Project (10371800) supported by the Research Council of Norway under the NEW Light (NEWLIGHT) Metals of the Strategic Area (SA) MaterialsProject (11JDG070) supported by the Senior Talent Research Foundation of Jiangsu University, China
文摘In order to explore the exact nature of deformation defects previously observed in nanostructured Al-Mg alloys subjected to severe plastic deformation, a more thorough examination of the radiation effect on the formation of the planar defects in the high pressure torsion （HPT） alloys was conducted using high-resolution transmission electron microscopy （HRTEM）. The results show that high density defects in the HRTEM images disappear completely when these images are exposed under the electron beam for some duration of time. At the same time, lattice defects are never observed within no-defect areas even when the beam-exposure increases to the degree that holes appear in the areas. Therefore, it is confirmed that the planar defects observed in the HPT alloys mainly result from the significant plastic deformation and are not due to the radiation effect during HRTEM observation.
基金financially supported by the Light Metals Educational Foundation of Japan,the Ministry of Education,Culture,Sports,Science and Technology (MEXT) of Japan (No. 19H05176,21H00150)the Russian Science Foundation (No. 17-19-01311)。
文摘To have an insight into the occurrence of inverse Hall-Petch relationship in ultrafine-grained(UFG) aluminum alloys produced by severe plastic deformation(SPD),ultra-SPD(i.e.inducing several ten thousand shear strains via high-pressure torsion,HPT) followed by aging is applied to an Al-La-Ce alloy.Average nanograin sizes of 40 and 80 nm are successfully achieved together with strain-induced Lomer-Cottrell dislocation lock formation and aging-induced semi-coherent Al_(11)(La,Ce)_3 precipitation.Analysis of hardening mechanisms in this alloy compared to SPD-processed pure aluminum with micrometer grain sizes,SPD-processed Al-based alloys with submicrometer grain sizes and ultra-SPD-processed Al-Ca alloy with nanograin sizes reveals the presence of two breaks in the Hall-Petch relationship.First,a positive upbreak appears when the grain sizes decrease from micrometer to submicrometer which is due to extra hardening by solute-dislocation interactions.Second,a negative down-break and softening occur by decreasing the grain sizes from submicrometer to nanometer which is caused by weakening the dislocation hardening mechanism with minor contribution of the inverse Hall-Petch mechanism.Detailed analyses confirm that nanograin formation is not necessarily a solution for extra hardening of Al-based alloys and other accompanying strategies such as grain-boundary segregation and precipitation are required to overcome such a down-break and softening.
基金Project(50971087) supported by the National Natural Science Foundation of ChinaProject supported by the Research Council of Norway under the Strategic University Program on Light Metals Technology Projects(67692, 71594) supported by the Hungarian National Science Foundation
文摘Deformation twins and stacking faults were observed in nanostructure A1-Mg alloys subjected to high pressure torsion. These observations are surprising because deformation twinnings have never been observed in their coarse-grained counterparts under normal conditions. Experimental evidences are introduced on non-equilibrium grain boundaries, deformation twinnings and partial dislocation emissions from grain boundaries. Some of these features can be explained by the results reported from molecular-dynamics simulations of pure FCC metals. Special emphasis is laid on the recent observations of high density hexagonal and rhombic shaped nanostructures with an average size of 3 nm in the A1-Mg alloys processed by high pressure torsion. A possible formation process of these nanostructures is proposed based on molecular-dynamics simulations.
基金supported by the National Key R&D Program of China (No. 2018YFC1106600)National Natural Science Foundation of China (NSFC)+4 种基金the Russian Foundation for Basic Research (RFBR) NSFC-RFBR Cooperative Project (No. 51611130054)the National Natural Science Foundation of China (Nos. 51431002 and 51871004)the National Natural Science Foundation of China (NSFC)the Research Grants Council (RGC) of Hong Kong NSFC-RGC Joint Research Scheme (Grant No. 5161101031)the financial support from Saint Petersburg State University in the framework of Call 3 project (id 26130576)
文摘Ti Ni alloys, with their unique shape memory effects and super elastic properties, occupy an indispensable place in the family of metallic biomaterials. In the past years, surface treatment is the main technique to improve the bioinert nature of microcrystalline Ti Ni alloys and inhibit on the release of toxic nickel ions to obtain excellent osteogenesis and osseointegration function. In the present study, nanocrystalline Ti49.2Ni50.8 alloy has been fabricated via equal channel angular pressing(ECAP), and the in vitro and in vivo studies revealed that it had enhanced cell viability, adhesion, proliferation, ALP(Alkaline phosphatase)activity and mineralization, and increased periphery thickness of new bone, in comparison to the commercial coarse-grained counterpart. These findings indicate that the reduction of grain size is beneficial to increasing the biocompatibility of Ti49.2Ni50.8 shape memory alloy.
基金supported by National Key R&D Program of China[grant number 2017YFE0123500]National Natural Science Foundation of China[grant number 51971072,51671064]+2 种基金the Fundamental Research Funds for the Central University[grant number HEUCFG201836]the support from the RFBR-CNPq-DST research project№19-58-80018the support in part from the Russian Foundation for Basic Research(project No.20-03-00614)。
文摘High-pressure torsion(HPT)processing under a pressure of 6.0 GPa was applied to Ti29.7Ni50.3Hf20(at.%)alloy.Two types of structure were observed after HPT with 3 revolutions:first one is the mixture of amorphous phase and retained nanocrystalline;second is the alternating bands of amorphous phase and high defect density crystalline.As a result,post deformation annealing(PDA)at 500-700℃leads to the non-uniform distribution of martensite and parent phase grains.The grains of martensite are twice larger compared to that of parent phase.The nanocrystalline and ultrafine grains form after annealing at 500-600℃and 700℃,respectively.The twinning mechanism does not change with the reduction of martensitic grains up to^35 nm.The relationship between strength and grain size in Ti29.7Ni50.3Hf20 alloy obeys the classical Hall-Petch relationship with a coefficient of 10.80±0.39 GPa nm^1/2.
