In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechani...In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechanical anisotropy was investigated.The results revealed that the alloy tube contains the high content(Mg1-xZnx)11Ce phase and the low content of Mg12Ce phase.These second phases are respectively incoherent and coherent with the Mg matrix,and their influence can be ignored.Additionally,the alloy tube exhibited a weak basal fiber texture,where the c-axis was aligned along the 0°∼30°tilt from TD to ED.Such a texture made the initial deformation(at 1.0%∼1.6%strain)of the three samples controlled by comparable basalslip.As deformation progressed(1.6∼9.0%strain),larger amounts of ETWs nucleated and gradually approached saturation in the three samples,re-orienting the c-axis to a 0°∼±30°deviation with respect to the loading directions.Meanwhile,the prismatic and pyramidal<c+a>slips replaced the dominant deformation progressively until fracture.Eventually,the similar deformation mechanisms determined by the weak initial texture in the three samples contribute to the comparable strain hardening rates,resulting in the low compressive anisotropy of the alloy tube.展开更多
Solidification cracking that occurs during continuous casting of 1Cr13 stainless steel was investigated with and without final elec- tromagnetic stirring （F-EMS）. The results show that cracks initiates and propagate...Solidification cracking that occurs during continuous casting of 1Cr13 stainless steel was investigated with and without final elec- tromagnetic stirring （F-EMS）. The results show that cracks initiates and propagates along the grain boundaries where the elements of carbon and sulfur are enriched. The final stirrer should be appropriately placed at a location that is 7.5 m away from the meniscus, and the appropri- ate thickness of the liquid core in the stirring zone is 50 ram. As a stirring current of 250 A is imposed, it can promote colurnnar-equiaxed transition, decrease the secondary dendrite arm spacing, and reduce the segregation of both carbon and sulfur. F-EMS can effectively de- crease the amount of cracks in 1Cr13 stainless steel.展开更多
A comprehensive two-dimensional axisymmetric mathematical model that couples transient electromagnetic force with fluid flow,heat transfer,and solidification was established to describe the interaction of multiphysics...A comprehensive two-dimensional axisymmetric mathematical model that couples transient electromagnetic force with fluid flow,heat transfer,and solidification was established to describe the interaction of multiphysics field during DC casting.The melt flow,heat transfer,and solidification characteristics under differential phase pulse magnetic field and differential phase low-frequency electromagnetic field(DP-PMF and DP-LFEF)were numerically investigated by means of numerical simulation during electromagnetic direct-chill(DC)casting of AZ31 alloy at the same casting conditions.The effects of differential phase electromagnetic fields on Lorentz forces distributions,melt flow,heat transfer,and liquid sump shape were discussed systematically.Based on measured current waveform,the results were compared with those obtained without magnetic field(MF)and under conventional pulse magnetic field(PMF)and low-frequency electromagnetic field(LFEF)under the same conditions.The results show that the application of magnetic fields can significantly change the solidification process of DC casting.Differential phase magnetic fields(DP-LFEF and DP-PMF)can effectively reduce the temperature of the melt in the liquid sump,and the shallower liquid sump depth can be obtained under the differential phase magnetic fields.A large velocity vibration amplitude and a lower temperature are available simultaneously under DP-PMF,resulting in more uniform temperature distribution.展开更多
The influences of the low frequency electromagnetic field on the horizontal direct chill casting process were investigated experimentally. Ingots of 2024 aluminum alloy with a cross size of 40 mm× 200 mm were pro...The influences of the low frequency electromagnetic field on the horizontal direct chill casting process were investigated experimentally. Ingots of 2024 aluminum alloy with a cross size of 40 mm× 200 mm were produced by the conventional horizontal chill casting process and low frequency electromagnetic horizontal chill casting processre- spectively. The as-cast structures and the mechanical property of the ingots were examined. The results showed that the low frequency electromagnetic field could sub- stantially refine the microstructures and pronouncedly reduce the macrosegregation in the horizontal direct chill casting process. Moreover, the surface quality of the ingot was prominently improved by the low frequency electromagnetic field. The fracture strength and elongation percentage of the ingot was increased with the low frequency electromagnetic field.展开更多
The influences of low frequency electromagnetic field on cast surface, microstructures and macrosegregation in horizontal direct chill(HDC) casting process were investigated experimentally. The cast surfaces, microstr...The influences of low frequency electromagnetic field on cast surface, microstructures and macrosegregation in horizontal direct chill(HDC) casting process were investigated experimentally. The cast surfaces, microstructures and macrosegregation of the ingots manufactured by conventional HDC and low frequency electromagnetic HDC casting were compared. The results show that low frequency electromagnetic field significantly improves the surface quality, refines the microstructures and reduces macrosegregation. Further more, increasing electromagnetic intensity or decreasing frequency is beneficial to the improvement. In the range of ampere-turns and frequency employed in the experiments, the optimum ampere-turns is found to be 10 000 A·turn and the frequency to be 30 Hz.展开更多
The hot deformation behaviours of 316LN-Mn austenitic stainless steel were investigated by uniaxial isothermal compression tests at different temperatures and strain rates.The microstructural evolutions were also stud...The hot deformation behaviours of 316LN-Mn austenitic stainless steel were investigated by uniaxial isothermal compression tests at different temperatures and strain rates.The microstructural evolutions were also studied using electron backscatter diffraction.The flow stress decreases with the increasing temperature and decreasing strain rate.A constitutive equation was established to characterize the relationship among the deformation parameters,and the deformation activation energy was calculated to be 497.92 k J/mol.Processing maps were constructed to describe the appropriate processing window,and the optimum processing parameters were determined at a temperature of 1107-1160℃ and a strain rate of 0.005-0.026 s^(-1).Experimental results showed that the main nucleation mechanism is discontinuous dynamic recrystallization(DDRX),followed by continuous dynamic recrystallization(CDRX).In addition,the formation of twin boundaries facilitated the nucleation of dynamic recrystallization.展开更多
The low frequency electromagnetic field was applied during direct chill(DC) semi-continuous casting of the ZK60 magnesium alloy billets. Effects of low frequency electromagnetic field on surface quality, microstructur...The low frequency electromagnetic field was applied during direct chill(DC) semi-continuous casting of the ZK60 magnesium alloy billets. Effects of low frequency electromagnetic field on surface quality, microstructure and hot-tearing tendency of Φ500 mm ZK60 magnesium alloy billets were investigated. The results showed that with the application of the low frequency electromagnetic field, the surface quality of the ZK60 magnesium alloy billets is markedly improved and the depth of cold fold is decreased. The microstructure of the billets is also significantly refined. Besides, the distribution of the grain size is relatively uniform from the billet surface towards its center, where the average grain size is 42 μm at surface and 50 μm at center. It also shows that the hot-tearing tendency of DC semi-continuous casting ZK60 magnesium alloy billets is significantly reduced under low frequency electromagnetic field.展开更多
High-performance magnesium alloys are moving towards a trend of being produced on a large scale and in an integrated manner.The foundational key to their successful production is the high-quality cast ingots.Magnesium...High-performance magnesium alloys are moving towards a trend of being produced on a large scale and in an integrated manner.The foundational key to their successful production is the high-quality cast ingots.Magnesium alloys produced through the conventional semi-continuous casting process inevitably contain casting defects,which makes it challenging to manufacture high-quality ingots.The integration of external field assisted controlled solidification technology,which combines physical fields such as electromagnetic and ultrasonic fields with traditional semi-continuous casting processes,enables the production of high-quality magnesium alloy ingots characterized by a homogeneous microstructure and absence of cracks.This article mainly summarizes the technical principles of those external field assisted casting process.The focus is on elaborating the refinement mechanism of different types of electromagnetic fields,ultrasonic fields,and combined physical fields during the solidification of magnesium alloys.Finally,the development prospects of producing highquality magnesium alloy ingots through semi-continuous casting under the external field were discussed.展开更多
Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during ...Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during casting,which are crucial for the quality of the ingot and can determine the success or failure of the casting operation.Numerical simulation,with the advantages of low cost,rapid execution,and visualized results,is an important method to study and optimize the DC casting process.In the present work,a simulation model of DC casting 2024 aluminum alloy was established,and the reliability of the model was verified.Then,the influence of casting parameters on flow field and temperature field was studied in detail by numerical simulation method.Results show that with the increase of casting speed,the melt flow becomes faster,the depths of slurry zone and mushy zone increase,and the variation of slurry zone depth is greater than that of mushy zone.With an increase in casting temperature,the melt flow rate increases,the depth of the slurry zone becomes shallower,and the depth of the mushy zone experiences only minor changes.The simulation results further indicate that the increase of the flow rate of the secondary cooling water slightly reduces the depths of both slurry and mushy zone.展开更多
The effects of low frequency electromagnetic (LFEC) field and ultrasonic (US) field on the microstructures, macrosegregation of alloying elements and the mechanical properties of DC cast AZ80 alloy were studied. The r...The effects of low frequency electromagnetic (LFEC) field and ultrasonic (US) field on the microstructures, macrosegregation of alloying elements and the mechanical properties of DC cast AZ80 alloy were studied. The results show that both LFEC and US fields can refine the grains of the billets, which results in the increase in mechanical properties and uniformity of alloying element distribution. The effective refinement takes place on the edge of ingots when LFEC field is applied, while in the center of billets when field US is adopted. Combined the characteristics of LFEC and US fields, a new process for direct-chilling (DC) casting of Mg-electromagnetic-ultrasonic (ECUS) casting is developed, by which the grains are refined significantly and are more uniform in the whole ingots, and the mechanical properties of the ingots are improved.展开更多
The heat treatment process has great effects on microstructure and conductivity of ingots. In this study, the ingots of high strength 7075 aluminum alloy were prepared by low frequency electromagnetic casting(LFEC), a...The heat treatment process has great effects on microstructure and conductivity of ingots. In this study, the ingots of high strength 7075 aluminum alloy were prepared by low frequency electromagnetic casting(LFEC), and the effect of different homogenization processes(single-step homogenization at 465 ℃ for different holding times and three-step homogenization) on the microstructure and conductivity of 7075 aluminum alloy were studied by means of metallographic microscopy, electrical conductivity test, differential thermal analysis and X-ray diffraction phase analysis. For comparison, the ingot by conventional direct casting(DC) under the same conditions was also prepared. Results show that the non-equilibrium eutectic phases with low melting point in the ingot dissolve continuously into the matrix as the holding time of single-step homogenization increases. The endothermic peak of non-equilibrium phases can not be completely eliminated through a 24 h single-step homogenization, but can be eliminated after a three-step homogenization(200 ℃/2 h + 460 ℃/6 h + 480 ℃/12 h). Meanwhile, the homogenization has a better effect on the LFEC ingot than the conventional DC ingot. Under the same homogenizing conditions, the grains of LFEC ingot are characterized by a lower content of low melting point phases and the ingot shows higher electrical conductivity than DC ingot.展开更多
The solidification structures of alloy 800H fabricated with and without linear electromagnetic stirring （L-EMS） were investigated. The results show that the solidification structure of the alloy can be obviously aff...The solidification structures of alloy 800H fabricated with and without linear electromagnetic stirring （L-EMS） were investigated. The results show that the solidification structure of the alloy can be obviously affected by the forced convection in melt caused with L-EMS decreases from 3.5 mm to 2.3 mm, by L-EMS. The average size of equiaxed grains of the alloy and the ratio of equiaxed grain increases from 5% to 43% compared with that without L-EMS. The microstructure of the alloy without L-EMS is composed of fine equiaxed dendrites in the outermost layer and columnar dendrites in other areas, whereas that with L-EMS contains equiaxed dendrites, columnar dendrites and cross dendrites. In addition, the mechanism of dendrite fragment drift was proved by examining the composition change of the main alloying elements in the dendrite trunks at different solidification stage using an electron probe micro-analyzer （EPMA）.展开更多
Based on multi-physical field coupling numerical simulation method,magnetic field distribution,melt flow,and heat transfer behavior of aΦ300 mm AZ80 alloy billet during differential phase electromagnetic DC casting(D...Based on multi-physical field coupling numerical simulation method,magnetic field distribution,melt flow,and heat transfer behavior of aΦ300 mm AZ80 alloy billet during differential phase electromagnetic DC casting(DP-EMC)with different electromagnetic parameters were studied.The results demonstrate that the increase in current intensity only changes the magnitude but does not change the Lorentz force's distribution characteristics.The maximum value of the Lorentz force increases linearly followed by an increase in current intensity.As the frequency increases,the Lorentz force's r component remains constant,and the z component decreases slightly.The change in current intensity correlates with the melt oscillation and convection intensity positively,as well as the liquid sump temperature uniformity.It does not mean that the higher the electric current,the better the metallurgical quality of the billet.A lower frequency is beneficial to generate a more significant melt flow and velocity fluctuation,which is helpful to create a more uniform temperature field.Appropriate DP-EMC parameters for aΦ300 mm AZ80 Mg alloy are 10-20 Hz frequency and 80-100 A current intensity.展开更多
Microstructure evolutions of an AZ80 magnesium alloy ingot with 300 mm in diameter cast with and without the electromagnetic vibration was investigated. The microstructures of the ingot cast with the conventional DC e...Microstructure evolutions of an AZ80 magnesium alloy ingot with 300 mm in diameter cast with and without the electromagnetic vibration was investigated. The microstructures of the ingot cast with the conventional DC exhibited relatively fine dendritic grains at the surface area, but coarse dendritic grains at the 1/2 radius and large equiaxed dendritic grains at the center. However, under the electromagnetic vibration casting condition, the microstructures of the ingot is significantly refined, especially those at the surface and at the center.展开更多
The combined electromagnetic fields were achieved by the application of an alternating magnetic field and a stationary magnetic field and were used during direct chill(DC) casting process to control the microstructure...The combined electromagnetic fields were achieved by the application of an alternating magnetic field and a stationary magnetic field and were used during direct chill(DC) casting process to control the microstructure and macrosegregation of an Al-Zn-Mg-Cu alloy. Ingot microstructures were analyzed under an optical microscope(Leica DMR). The composition at different locations in the ingots was measured with inductively coupled plasma mass spectrometry(ICP) method. The results showed that the grain structure is transformed from dendrite to equiaxed structure and significantly refined with the application of combined electromagnetic fields. The uniformity of microstructure is also greatly improved. The combined electromagnetic fields show a significant effect on the distribution of elements. The negative macrosegregation in the centre area of the ingot is obviously reduced.展开更多
The influences of out-phase electromagnetic field on the as-cast structure of horizontal direct chill casting aluminum alloy ingot were experimental by and numerical by studied. The results of numerical analysis show ...The influences of out-phase electromagnetic field on the as-cast structure of horizontal direct chill casting aluminum alloy ingot were experimental by and numerical by studied. The results of numerical analysis show that the interaction of the out-phase electromagnetic field and the melt can generate an electromagnetically induced forced flow in the melt, which, in turn, changes flow pattern and temperature field in the mold. The as-cast structure of the ingot can be greatly improved by the changes of flow pattern and temperature field. The results of experimental analysis show that with application of out-phase electromagnetic field, temperature distribution in the melt is more uniform, grain morphology changes from columnar grains to equiaxed grains and grain size decreases.展开更多
The influence of forging and aging treatment on mechanical properties and microstructure of large size prestretched thick plate of 7B04 aluminium alloy was investigated through tensile test, corrosion test, transmissi...The influence of forging and aging treatment on mechanical properties and microstructure of large size prestretched thick plate of 7B04 aluminium alloy was investigated through tensile test, corrosion test, transmission electronic microcopy(TEM) and energy dispersive spectrum(EDS) analysis. The results show that the properties of plate performed extra forging (FSR technology) are much higher than those of plate without forging (CSR technology). T7451 temper is preferred to resisting corrosion than T651 temper due to a wide PFZ and discontinuous grain boundary precipitates.展开更多
With the aid of ANSYS software, the effect of different mould external part materials on magnetic flux density in the aluminum melt and magnetic field interaction of four coils applied with same currents were investig...With the aid of ANSYS software, the effect of different mould external part materials on magnetic flux density in the aluminum melt and magnetic field interaction of four coils applied with same currents were investigated. Calculating results showed that magnetic flux density in the aluminum melt was greatly improved and the magnetic field interaction among different coils was decreased when external part of mould is made of soft magnetic material. Based on the finding, a four-strand low-frequency electromagnetic casting 6063 aluminum alloy experiment was carried out in the laboratory . The experiment showed that the surface of the billet was smooth and had no exudations and cold shuts, the as-cast microstructures were fine, uniform, equiaxed, net-globular or globular under low-frequency electromagnetic field. The microstructure becomes finer with increased current value.展开更多
Al-Zn-Mg-Cu-Zr ingots with diameter of 200 mm were made by low frequency electromagnetic casting (LFEC) and conventional direct chill (DC) casting process. The results show that under the low frequency electromagnetic...Al-Zn-Mg-Cu-Zr ingots with diameter of 200 mm were made by low frequency electromagnetic casting (LFEC) and conventional direct chill (DC) casting process. The results show that under the low frequency electromagnetic field (25 Hz, 32 mT) the microstructures of LFEC ingot from the border to the center on the cross section are all equiaxed grains, and the grains are much finer and more uniform than that of DC ingot. The magnetic flux density plays an important role in the microstructure formation of LFEC ingots. With increasing the magnetic flux density from 0 mT to 32 mT, grains become finer (from about 120 urn to 30 urn) and more uniform. While, with increasing the magnetic flux density from 32 mT to 46 mT, the grains change much slowly. In the range of experimental parameters, the optimum magnetic flux density for LFEC process is found to be 32 mT.展开更多
The d 120 mm ingots of 7050 aluminum alloy were made by low frequency electromagnetic casting(LFEC) and conventional DC casting process,respectively. After homogenization treatment the ingots were extruded to rods and...The d 120 mm ingots of 7050 aluminum alloy were made by low frequency electromagnetic casting(LFEC) and conventional DC casting process,respectively. After homogenization treatment the ingots were extruded to rods and the solution and aging treatment were carried out for the rods. Constituents evolution during processing and effects of LFEC on constituents and remnant constituents were studied. The results show that 7050 aluminum alloy mainly contains Al-Zn-Mg-Cu type and Al-Cu-Fe type constituents. Al-Zn-Mg-Cu type constituents dissolve during homogenization,while Al-Cu-Fe type constituents could not dissolve. After homogenization treatment,the main remnant constituent is Al7Cu2Fe which crushes and orients along the extrusion direction after extrusion. Compared with DC process,by the process of LFEC,the constituents or remnant constituents are smaller in size and less in content. The LFEC process shows significant improvement in elongation by LFEC in both as-cast state and final state.展开更多
基金supported by the National Natural Science Foundation of China(Nos.51974082,51901037)State Key Laboratory of Baiyunobo Rare Earth Resource Research and Comprehensive Utilization(No.2021H2279)Programme of Introducing Talents of Discipline Innovation to Universities 2.0(the 111 Project 2.0 of China,No.BP0719037).
文摘In this study,the extruded Mg-Zn-Mn-Ce-Ca alloy tube with a low compression anisotropy along the ED,45ED and TD was prepared.The effect of the second phases,initial texture and deformation behavior on this low mechanical anisotropy was investigated.The results revealed that the alloy tube contains the high content(Mg1-xZnx)11Ce phase and the low content of Mg12Ce phase.These second phases are respectively incoherent and coherent with the Mg matrix,and their influence can be ignored.Additionally,the alloy tube exhibited a weak basal fiber texture,where the c-axis was aligned along the 0°∼30°tilt from TD to ED.Such a texture made the initial deformation(at 1.0%∼1.6%strain)of the three samples controlled by comparable basalslip.As deformation progressed(1.6∼9.0%strain),larger amounts of ETWs nucleated and gradually approached saturation in the three samples,re-orienting the c-axis to a 0°∼±30°deviation with respect to the loading directions.Meanwhile,the prismatic and pyramidal<c+a>slips replaced the dominant deformation progressively until fracture.Eventually,the similar deformation mechanisms determined by the weak initial texture in the three samples contribute to the comparable strain hardening rates,resulting in the low compressive anisotropy of the alloy tube.
基金financially supported by the National Natural Science Foundation of China (No. 50834009)the Key Project of the Ministry of Education of China (No. 311014)the 111 Project of China (No. B07015)
文摘Solidification cracking that occurs during continuous casting of 1Cr13 stainless steel was investigated with and without final elec- tromagnetic stirring （F-EMS）. The results show that cracks initiates and propagates along the grain boundaries where the elements of carbon and sulfur are enriched. The final stirrer should be appropriately placed at a location that is 7.5 m away from the meniscus, and the appropri- ate thickness of the liquid core in the stirring zone is 50 ram. As a stirring current of 250 A is imposed, it can promote colurnnar-equiaxed transition, decrease the secondary dendrite arm spacing, and reduce the segregation of both carbon and sulfur. F-EMS can effectively de- crease the amount of cracks in 1Cr13 stainless steel.
基金the National Natural Science Foundation of China(51974082)the National Natural Science Foundation of China(51771043)the Programme of Introducing Talents of Discipline Innovation to Universities 2.0(the 111 Project 2.0 of China,No.BP0719037).
文摘A comprehensive two-dimensional axisymmetric mathematical model that couples transient electromagnetic force with fluid flow,heat transfer,and solidification was established to describe the interaction of multiphysics field during DC casting.The melt flow,heat transfer,and solidification characteristics under differential phase pulse magnetic field and differential phase low-frequency electromagnetic field(DP-PMF and DP-LFEF)were numerically investigated by means of numerical simulation during electromagnetic direct-chill(DC)casting of AZ31 alloy at the same casting conditions.The effects of differential phase electromagnetic fields on Lorentz forces distributions,melt flow,heat transfer,and liquid sump shape were discussed systematically.Based on measured current waveform,the results were compared with those obtained without magnetic field(MF)and under conventional pulse magnetic field(PMF)and low-frequency electromagnetic field(LFEF)under the same conditions.The results show that the application of magnetic fields can significantly change the solidification process of DC casting.Differential phase magnetic fields(DP-LFEF and DP-PMF)can effectively reduce the temperature of the melt in the liquid sump,and the shallower liquid sump depth can be obtained under the differential phase magnetic fields.A large velocity vibration amplitude and a lower temperature are available simultaneously under DP-PMF,resulting in more uniform temperature distribution.
文摘The influences of the low frequency electromagnetic field on the horizontal direct chill casting process were investigated experimentally. Ingots of 2024 aluminum alloy with a cross size of 40 mm× 200 mm were produced by the conventional horizontal chill casting process and low frequency electromagnetic horizontal chill casting processre- spectively. The as-cast structures and the mechanical property of the ingots were examined. The results showed that the low frequency electromagnetic field could sub- stantially refine the microstructures and pronouncedly reduce the macrosegregation in the horizontal direct chill casting process. Moreover, the surface quality of the ingot was prominently improved by the low frequency electromagnetic field. The fracture strength and elongation percentage of the ingot was increased with the low frequency electromagnetic field.
文摘The influences of low frequency electromagnetic field on cast surface, microstructures and macrosegregation in horizontal direct chill(HDC) casting process were investigated experimentally. The cast surfaces, microstructures and macrosegregation of the ingots manufactured by conventional HDC and low frequency electromagnetic HDC casting were compared. The results show that low frequency electromagnetic field significantly improves the surface quality, refines the microstructures and reduces macrosegregation. Further more, increasing electromagnetic intensity or decreasing frequency is beneficial to the improvement. In the range of ampere-turns and frequency employed in the experiments, the optimum ampere-turns is found to be 10 000 A·turn and the frequency to be 30 Hz.
基金financial support of the National Natural Science Foundation of China(Nos.52101105 and 51975263)。
文摘The hot deformation behaviours of 316LN-Mn austenitic stainless steel were investigated by uniaxial isothermal compression tests at different temperatures and strain rates.The microstructural evolutions were also studied using electron backscatter diffraction.The flow stress decreases with the increasing temperature and decreasing strain rate.A constitutive equation was established to characterize the relationship among the deformation parameters,and the deformation activation energy was calculated to be 497.92 k J/mol.Processing maps were constructed to describe the appropriate processing window,and the optimum processing parameters were determined at a temperature of 1107-1160℃ and a strain rate of 0.005-0.026 s^(-1).Experimental results showed that the main nucleation mechanism is discontinuous dynamic recrystallization(DDRX),followed by continuous dynamic recrystallization(CDRX).In addition,the formation of twin boundaries facilitated the nucleation of dynamic recrystallization.
基金financially supported by the Major State Basic Research Development Program of China(Grant No.2013CB632203)the Liaoning Provincial Natural Science Foundation of China(Grant No.201202072)+1 种基金the Program for Liaoning Excellent Talents in University(Grant No.LJQ2012023)the Fundamental Research Foundation of Central Universities(Grant Nos.N120509002 and N120309003)
文摘The low frequency electromagnetic field was applied during direct chill(DC) semi-continuous casting of the ZK60 magnesium alloy billets. Effects of low frequency electromagnetic field on surface quality, microstructure and hot-tearing tendency of Φ500 mm ZK60 magnesium alloy billets were investigated. The results showed that with the application of the low frequency electromagnetic field, the surface quality of the ZK60 magnesium alloy billets is markedly improved and the depth of cold fold is decreased. The microstructure of the billets is also significantly refined. Besides, the distribution of the grain size is relatively uniform from the billet surface towards its center, where the average grain size is 42 μm at surface and 50 μm at center. It also shows that the hot-tearing tendency of DC semi-continuous casting ZK60 magnesium alloy billets is significantly reduced under low frequency electromagnetic field.
基金supported by the National Natural Science Foundation of China(No.52274377 and No.52304391)the Natural Science Foundation of Liaoning Province(No.2023-MSBA-133)the Fundamental Research Funds for the Central Universities(No.N2402010).
文摘High-performance magnesium alloys are moving towards a trend of being produced on a large scale and in an integrated manner.The foundational key to their successful production is the high-quality cast ingots.Magnesium alloys produced through the conventional semi-continuous casting process inevitably contain casting defects,which makes it challenging to manufacture high-quality ingots.The integration of external field assisted controlled solidification technology,which combines physical fields such as electromagnetic and ultrasonic fields with traditional semi-continuous casting processes,enables the production of high-quality magnesium alloy ingots characterized by a homogeneous microstructure and absence of cracks.This article mainly summarizes the technical principles of those external field assisted casting process.The focus is on elaborating the refinement mechanism of different types of electromagnetic fields,ultrasonic fields,and combined physical fields during the solidification of magnesium alloys.Finally,the development prospects of producing highquality magnesium alloy ingots through semi-continuous casting under the external field were discussed.
基金financially supported by the National Natural Science Foundation of China(No.51674078)。
文摘Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting process.These parameters significantly influence the flow and temperature fields during casting,which are crucial for the quality of the ingot and can determine the success or failure of the casting operation.Numerical simulation,with the advantages of low cost,rapid execution,and visualized results,is an important method to study and optimize the DC casting process.In the present work,a simulation model of DC casting 2024 aluminum alloy was established,and the reliability of the model was verified.Then,the influence of casting parameters on flow field and temperature field was studied in detail by numerical simulation method.Results show that with the increase of casting speed,the melt flow becomes faster,the depths of slurry zone and mushy zone increase,and the variation of slurry zone depth is greater than that of mushy zone.With an increase in casting temperature,the melt flow rate increases,the depth of the slurry zone becomes shallower,and the depth of the mushy zone experiences only minor changes.The simulation results further indicate that the increase of the flow rate of the secondary cooling water slightly reduces the depths of both slurry and mushy zone.
基金Projects(2007CB613701, 2007CB613702) supported by the National Basic Research Program of ChinaProjects(50974037, 50904018) supported by the National Natural Science Foundation of China+1 种基金Project(NCET-08-0098) supported by New Century Excellent Talents in Chinese UniversityProject(N90209002) supported by the Special Foundation for Basic Scientific Research of Central Colleges
文摘The effects of low frequency electromagnetic (LFEC) field and ultrasonic (US) field on the microstructures, macrosegregation of alloying elements and the mechanical properties of DC cast AZ80 alloy were studied. The results show that both LFEC and US fields can refine the grains of the billets, which results in the increase in mechanical properties and uniformity of alloying element distribution. The effective refinement takes place on the edge of ingots when LFEC field is applied, while in the center of billets when field US is adopted. Combined the characteristics of LFEC and US fields, a new process for direct-chilling (DC) casting of Mg-electromagnetic-ultrasonic (ECUS) casting is developed, by which the grains are refined significantly and are more uniform in the whole ingots, and the mechanical properties of the ingots are improved.
基金financially supported by the National Natural Science Foundation of China(youth)(No.51004036)the Fundamental Research Funds(N120309002)
文摘The heat treatment process has great effects on microstructure and conductivity of ingots. In this study, the ingots of high strength 7075 aluminum alloy were prepared by low frequency electromagnetic casting(LFEC), and the effect of different homogenization processes(single-step homogenization at 465 ℃ for different holding times and three-step homogenization) on the microstructure and conductivity of 7075 aluminum alloy were studied by means of metallographic microscopy, electrical conductivity test, differential thermal analysis and X-ray diffraction phase analysis. For comparison, the ingot by conventional direct casting(DC) under the same conditions was also prepared. Results show that the non-equilibrium eutectic phases with low melting point in the ingot dissolve continuously into the matrix as the holding time of single-step homogenization increases. The endothermic peak of non-equilibrium phases can not be completely eliminated through a 24 h single-step homogenization, but can be eliminated after a three-step homogenization(200 ℃/2 h + 460 ℃/6 h + 480 ℃/12 h). Meanwhile, the homogenization has a better effect on the LFEC ingot than the conventional DC ingot. Under the same homogenizing conditions, the grains of LFEC ingot are characterized by a lower content of low melting point phases and the ingot shows higher electrical conductivity than DC ingot.
基金financially supported by the National Nature Science Foundation of China(No.50834009)the Key(Key Grant)Project of the Ministry of Education of P.R.China(No.311014)+1 种基金the Fundamental Research Funds for the Central Universities of China(No.N090609001 and No.N100409005)the Programme of Introducing Talents of Discipline to Universities(the 111 Project of China,No.B07015)
文摘The solidification structures of alloy 800H fabricated with and without linear electromagnetic stirring （L-EMS） were investigated. The results show that the solidification structure of the alloy can be obviously affected by the forced convection in melt caused with L-EMS decreases from 3.5 mm to 2.3 mm, by L-EMS. The average size of equiaxed grains of the alloy and the ratio of equiaxed grain increases from 5% to 43% compared with that without L-EMS. The microstructure of the alloy without L-EMS is composed of fine equiaxed dendrites in the outermost layer and columnar dendrites in other areas, whereas that with L-EMS contains equiaxed dendrites, columnar dendrites and cross dendrites. In addition, the mechanism of dendrite fragment drift was proved by examining the composition change of the main alloying elements in the dendrite trunks at different solidification stage using an electron probe micro-analyzer （EPMA）.
基金the Fundamental Research Funds for the Central Universities(Grant No.N2009003)the National Natural Science Foundation of China(Grant No.51904151).
文摘Based on multi-physical field coupling numerical simulation method,magnetic field distribution,melt flow,and heat transfer behavior of aΦ300 mm AZ80 alloy billet during differential phase electromagnetic DC casting(DP-EMC)with different electromagnetic parameters were studied.The results demonstrate that the increase in current intensity only changes the magnitude but does not change the Lorentz force's distribution characteristics.The maximum value of the Lorentz force increases linearly followed by an increase in current intensity.As the frequency increases,the Lorentz force's r component remains constant,and the z component decreases slightly.The change in current intensity correlates with the melt oscillation and convection intensity positively,as well as the liquid sump temperature uniformity.It does not mean that the higher the electric current,the better the metallurgical quality of the billet.A lower frequency is beneficial to generate a more significant melt flow and velocity fluctuation,which is helpful to create a more uniform temperature field.Appropriate DP-EMC parameters for aΦ300 mm AZ80 Mg alloy are 10-20 Hz frequency and 80-100 A current intensity.
文摘Microstructure evolutions of an AZ80 magnesium alloy ingot with 300 mm in diameter cast with and without the electromagnetic vibration was investigated. The microstructures of the ingot cast with the conventional DC exhibited relatively fine dendritic grains at the surface area, but coarse dendritic grains at the 1/2 radius and large equiaxed dendritic grains at the center. However, under the electromagnetic vibration casting condition, the microstructures of the ingot is significantly refined, especially those at the surface and at the center.
基金supported by the National Natural Science Foundation of China(51374067)the Outstanding Young Scholars'Growth Plan in the Colleges and Universities of Liaoning Province(LJQ2014032)the National Basic Research Program of China(2012CB619506)
文摘The combined electromagnetic fields were achieved by the application of an alternating magnetic field and a stationary magnetic field and were used during direct chill(DC) casting process to control the microstructure and macrosegregation of an Al-Zn-Mg-Cu alloy. Ingot microstructures were analyzed under an optical microscope(Leica DMR). The composition at different locations in the ingots was measured with inductively coupled plasma mass spectrometry(ICP) method. The results showed that the grain structure is transformed from dendrite to equiaxed structure and significantly refined with the application of combined electromagnetic fields. The uniformity of microstructure is also greatly improved. The combined electromagnetic fields show a significant effect on the distribution of elements. The negative macrosegregation in the centre area of the ingot is obviously reduced.
基金Supported by Postdoctor Fund of Northeastern University
文摘The influences of out-phase electromagnetic field on the as-cast structure of horizontal direct chill casting aluminum alloy ingot were experimental by and numerical by studied. The results of numerical analysis show that the interaction of the out-phase electromagnetic field and the melt can generate an electromagnetically induced forced flow in the melt, which, in turn, changes flow pattern and temperature field in the mold. The as-cast structure of the ingot can be greatly improved by the changes of flow pattern and temperature field. The results of experimental analysis show that with application of out-phase electromagnetic field, temperature distribution in the melt is more uniform, grain morphology changes from columnar grains to equiaxed grains and grain size decreases.
基金Project(2003AA331100) supported by Commission of Science Technology and Industry for National Defence
文摘The influence of forging and aging treatment on mechanical properties and microstructure of large size prestretched thick plate of 7B04 aluminium alloy was investigated through tensile test, corrosion test, transmission electronic microcopy(TEM) and energy dispersive spectrum(EDS) analysis. The results show that the properties of plate performed extra forging (FSR technology) are much higher than those of plate without forging (CSR technology). T7451 temper is preferred to resisting corrosion than T651 temper due to a wide PFZ and discontinuous grain boundary precipitates.
文摘With the aid of ANSYS software, the effect of different mould external part materials on magnetic flux density in the aluminum melt and magnetic field interaction of four coils applied with same currents were investigated. Calculating results showed that magnetic flux density in the aluminum melt was greatly improved and the magnetic field interaction among different coils was decreased when external part of mould is made of soft magnetic material. Based on the finding, a four-strand low-frequency electromagnetic casting 6063 aluminum alloy experiment was carried out in the laboratory . The experiment showed that the surface of the billet was smooth and had no exudations and cold shuts, the as-cast microstructures were fine, uniform, equiaxed, net-globular or globular under low-frequency electromagnetic field. The microstructure becomes finer with increased current value.
基金Project(2005CB623707) supported by the National Basic Research Program of China
文摘Al-Zn-Mg-Cu-Zr ingots with diameter of 200 mm were made by low frequency electromagnetic casting (LFEC) and conventional direct chill (DC) casting process. The results show that under the low frequency electromagnetic field (25 Hz, 32 mT) the microstructures of LFEC ingot from the border to the center on the cross section are all equiaxed grains, and the grains are much finer and more uniform than that of DC ingot. The magnetic flux density plays an important role in the microstructure formation of LFEC ingots. With increasing the magnetic flux density from 0 mT to 32 mT, grains become finer (from about 120 urn to 30 urn) and more uniform. While, with increasing the magnetic flux density from 32 mT to 46 mT, the grains change much slowly. In the range of experimental parameters, the optimum magnetic flux density for LFEC process is found to be 32 mT.
基金Projects (2005CB623707) supported by the National Key Basic Research Program of China
文摘The d 120 mm ingots of 7050 aluminum alloy were made by low frequency electromagnetic casting(LFEC) and conventional DC casting process,respectively. After homogenization treatment the ingots were extruded to rods and the solution and aging treatment were carried out for the rods. Constituents evolution during processing and effects of LFEC on constituents and remnant constituents were studied. The results show that 7050 aluminum alloy mainly contains Al-Zn-Mg-Cu type and Al-Cu-Fe type constituents. Al-Zn-Mg-Cu type constituents dissolve during homogenization,while Al-Cu-Fe type constituents could not dissolve. After homogenization treatment,the main remnant constituent is Al7Cu2Fe which crushes and orients along the extrusion direction after extrusion. Compared with DC process,by the process of LFEC,the constituents or remnant constituents are smaller in size and less in content. The LFEC process shows significant improvement in elongation by LFEC in both as-cast state and final state.
